Detection response time

Leak and shock detection Response time <1 min High accuracy (<1%)... 

Analyte Sample matrix Tissue Sensing element Linear range (mol 1 1) Limit of detection Response time Lifetime Ref. 

Agent Gas detection tube Limit of detection Response time... 

As with all methods and devices for quantitative analysis, the optimization of electrochemical biosensors is directed at the following features (linear) measuring range, lower limit of detection, response time and sample frequency, precision, accuracy, stability, and selectivity for the target analyte. 

Within the IBP, many types of sampling devices both from the collection viewpoint and the subsequent assay viewpoint have been examined to improve the specificity and detection response time. 

One important electrochemical technology where diamond electrodes have made a significant impact is in the area of electroanalysis. CVD diamond offers advantages over other electrodes, especially sp carbon (e.g., glassy carbon), in terms of linear dynamic range, limit of detection, response time, response precision, and response stability. Some of the reported applications of diamond in electroanalysis are highlighted below. Unless stated otherwise, all the diamond electrodes mentioned below are boron-doped, microcrystalline thin films deposited on a conducting substrate (e.g.. Si). 

Naturally, it is difficult to characterize them, and also LOPA does not include initiating events due corrosion, etc. Detection coverage factor, related to detection effectiveness, the number of detectors, and the placement of detectors at a given elevation are very important for performance-based systems. For gas detectors, this also depends on the type of gas, gas density relative to ambient air, etc. Detection response time is very critical as the FGS must operate within its mitigation limits. Also, ESDs demand for a definite specified response time. Performance approach for FGS has two parts ... 

Direct time-dependent detection is limited by the response time of detectors, which depends on the frequency range, and the electronics used for data acquisition. In the most favourable cases, modem detector/oscilloscope combinations achieve a time resolution of up to 100 ps, but 1 ns is more typical. Again, this reaction has been of fiindamental theoretical interest for a long time [59, 60]. 

There are important figures of merit (5) that describe the performance of a photodetector. These are responsivity, noise, noise equivalent power, detectivity, and response time (2,6). However, there are several related parameters of measurement, eg, temperature of operation, bias power, spectral response, background photon flux, noise spectra, impedance, and linearity. Operational concerns include detector-element size, uniformity of response, array density, reflabiUty, cooling time, radiation tolerance, vibration and shock resistance, shelf life, availabiUty of arrays, and cost. 

The low detection limit, high sensitivity, and fast response times of chemoreceptor-based biosensors result primarily from the extremely high binding constants of the receptor R for the target substrate S. The receptor—substrate binding may be described... 

The dye is excited by light suppHed through the optical fiber (see Fiber optics), and its fluorescence monitored, also via the optical fiber. Because molecular oxygen, O2, quenches the fluorescence of the dyes employed, the iatensity of the fluorescence is related to the concentration of O2 at the surface of the optical fiber. Any glucose present ia the test solution reduces the local O2 concentration because of the immobilized enzyme resulting ia an iacrease ia fluorescence iatensity. This biosensor has a detection limit for glucose of approximately 100 ]lM , response times are on the order of a miaute. 

The most important hardware items appeared to be the detectors themselves. The gas detection system gave frequent spurious alarms, and on both platforms the ultraviolet (UV) fire detectors were also prone to spurious activation from distant hot work for example, and had a limited ability to detect real fires. The tmreliability of these systems had a general effect on response time and would, overall, lengthen the time to respond. The second aspect which was related to hardware was fimction and performance testing of the emergency blowdown systems. It is critical that the workers believe the systems will work when required, and this can only be achieved by occasional use or at least fimction testing. 

Protection is the branch of electric power engineering concerned with the principles of design and operation of equipment (called relays nr protective relays ) which detect abnormal power system conditions and initiate corrective action as quickly as possible in order to return the power system to its normal state. The quickness of response is an essential element of protective relaying systems—response times of the order of a few milliseconds are often required. Consequently, human intervention in the protection of system operation is not possible. The response must be automatic, quick, and should cause a minimum amount of disruption to the power system. 

The high specificity required for the analysis of physiological fluids often necessitates the incorporation of permselective membranes between the sample and the sensor. A typical configuration is presented in Fig. 7, where the membrane system comprises three distinct layers. The outer membrane. A, which encounters the sample solution is indicated by the dashed lines. It most commonly serves to eliminate high molecular weight interferences, such as other enzymes and proteins. The substrate, S, and other small molecules are allowed to enter the enzyme layer, B, which typically consist of a gelatinous material or a porous solid support. The immobilized enzyme catalyzes the conversion of substrate, S, to product, P. The substrate, product or a cofactor may be the species detected electrochemically. In many cases the electrochemical sensor may be prone to interferences and a permselective membrane, C, is required. The response time and sensitivity of the enzyme electrode will depend on the rate of permeation through layers A, B and C the kinetics of enzymatic conversion as well as the charac-... 

API Serial Dilution Method. The API serial dilution method is the most widely used method for the detection of microorganisms. Field test methods for estimating bacterial populations have been standardized. A standard method dealing with the dose-response (time-kill) testing for evaluating biocides has been established. Sampling methods are of special importance because effective sampling is essential to any successful analysis. 

Sol-gel-derived membranes encapsulating a bis(crown ether) derivative [bis(12-crown-4-ylmethyl) 2-dodecyl-2-methylmalonate] [28] were also fabricated with an initial DEDMS/TEOS ratio of 3 for Na -ISFETs. The Na -ISFETs showed a Nernstian response to Na+ activity changes in the activity range of 1 x 10 " to 1 M and a short response time of 2 s. Employment of a polythiophene interlayer improved the potential instability and the lower detection limit in both of the K - and Na -ISFETs based on the sol-gel-derived membranes with the initial DEDMS/TEOS ratio of 3 (Fig. 8). 

---