Degree cellulose

Only cellulose acetobutyrate and, to a limited degree, cellulose propionate molding compounds can be effectively equipped with weathering stabiiizers. For ceiiuiose diacetate molding compounds, no climate stabiiizer has yet been found that maintains serviceability even after years of outdoor weathering. 

Lead azide is not readily dead-pressed, ie, pressed to a point where it can no longer be initiated. However, this condition is somewhat dependent on the output of the mixture used to ignite the lead azide and the degree of confinement of the system. Because lead azide is a nonconductor, it may be mixed with flaked graphite to form a conductive mix for use in low energy electric detonators. A number of different types of lead azide have been prepared to improve its handling characteristics and performance and to decrease sensitivity. In addition to the dextrinated lead azide commonly used in the United States, service lead azide, which contains a minimum of 97% lead azide and no protective colloid, is used in the United Kingdom. Other varieties include colloidal lead azide (3—4 pm), poly(vinyl alcohol)-coated lead azide, and British RE) 1333 and RE) 1343 lead azide which is precipitated in the presence of carboxymethyl cellulose (88—92). 

Cellulose triacetate is obtained by the esterification of cellulose (qv) with acetic anhydride (see Cellulose esters). Commercial triacetate is not quite the precise chemical entity depicted as (1) because acetylation does not quite reach the maximum 3.0 acetyl groups per glucose unit. Secondary cellulose acetate is obtained by hydrolysis of the triacetate to an average degree of substitution (DS) of 2.4 acetyl groups per glucose unit. There is no satisfactory commercial means to acetylate direcdy to the 2.4 acetyl level and obtain a secondary acetate that has the desired solubiUty needed for fiber preparation. 

Tables 1 and 2 Hst the important physical properties of formamide. Form amide is more highly hydrogen bonded than water at temperatures below 80°C but the degree of molecular association decreases rapidly with increa sing temperature. Because of its high dielectric constant, formamide is an excellent ionizing solvent for many inorganic salts and also for peptides, proteias (eg, keratin), polysaccharides (eg, cellulose [9004-34-6] starch [9005-25-8]) and resias.

Carboxymethylcellulose Sodium. Carboxymethyl ether of cellulose sodium salt (Citmcel) (8) is a white granular substance soluble in water depending on the degree of substitution. It is equally soluble in cold and hot water and may be prepared by treating alkaU cellulose with sodium chloroacetate. 

Sodium carboxymethyl cellulose [9004-32-4] (CMC) and hydroxyethyl cellulose [9004-62-0] (HEC) are the ceUulosics most widely used in drilling fluids (43). CMC is manufactured by carboxymethylation of cellulose which changes the water-insoluble cellulose into the water-soluble CMC (44). Hydroxyethyl cellulose and carboxymethyl hydroxyethyl cellulose (CMHEC) are made by a similar process. The viscosity grade of the material is determined by the degree of substitution and the molecular weight of the finished product. 

An important chemical finishing process for cotton fabrics is that of mercerization, which improves strength, luster, and dye receptivity. Mercerization iavolves brief exposure of the fabric under tension to concentrated (20—25 wt %) NaOH solution (14). In this treatment, the cotton fibers become more circular ia cross-section and smoother ia surface appearance, which iacreases their luster. At the molecular level, mercerization causes a decrease ia the degree of crystallinity and a transformation of the cellulose crystal form. These fine stmctural changes iacrease the moisture and dye absorption properties of the fiber. Biopolishing is a relatively new treatment of cotton fabrics, involving ceUulase enzymes, to produce special surface effects (15). 

Emulsion polymerizations of vinyl acetate in the presence of ethylene oxide- or propylene oxide-based surfactants and protective coUoids also are characterized by the formation of graft copolymers of vinyl acetate on these materials. This was also observed in mixed systems of hydroxyethyl cellulose and nonylphenol ethoxylates. The oxyethylene chain groups supply the specific site of transfer (111). The concentration of insoluble (grafted) polymer decreases with increase in surfactant ratio, and (max) is observed at an ethoxylation degree of 8 (112). 

Cellulose is the main component of the wood cell wall, typically 40—50% by weight of the dry wood. Pure cellulose is a polymer of glucose residues joined by 1,4-P-glucosidic bonds. The degree of polymerization (DP) is variable and may range from 700 to 10,000 DP or more. Wood cellulose is more resistant to dilute acid hydrolysis than hemiceUulose. X-ray diffraction indicates a partial crystalline stmcture for wood cellulose. The crystalline regions are more difficult to hydrolyze than the amorphous regions because removal of the easily hydrolyzed material has Htde effect on the diffraction pattern. 

Every polysaccharide contains glycosyl units with unsubstituted hydroxyl groups available for esterification or etherification. Polysaccharide derivatives are described by their degree of substitution (DS), which is the average number of substituent groups per glycosyl unit. Because each monomeric unit of cellulose molecules has free hydroxyl groups at C-2, C-3, and C-6, the maximum DS for cellulose, and all polysaccharides composed exclusively of neutral hexosyl units, the majority of polysaccharides, is 3.0. 

Cellulose acetate [9004-35-7] is the most important organic ester because of its broad appHcation in fibers and plastics it is prepared in multi-ton quantities with degrees of substitution (DS) ranging from that of hydrolyzed, water-soluble monoacetates to those of fully substituted triacetate (Table 1). Soluble cellulose acetate was first prepared in 1865 by heating cotton and acetic anhydride at 180°C (1). Using sulfuric acid as a catalyst permitted preparation at lower temperatures (2), and later, partial hydrolysis of the triacetate gave an acetone-soluble cellulose acetate (3). The solubiUty of partially hydrolyzed (secondary) cellulose acetate in less expensive and less toxic solvents such as acetone aided substantially in its subsequent commercial development. 

Cellulose dissolved in suitable solvents, however, can be acetylated in a totally homogeneous manner, and several such methods have been suggested. Treatment in dimethyl sulfoxide (DMSO) with paraformaldehyde gives a soluble methylol derivative that reacts with glacial acetic acid, acetic anhydride, or acetyl chloride to form the acetate (63). The maximum degree of substitution obtained by this method is 2.0 some oxidation also occurs. Similarly, cellulose can be acetylated in solution with dimethylacetamide—paraformaldehyde and dimethylformamide-paraformaldehyde with a potassium acetate catalyst (64) to provide an almost quantitative yield of hydroxymethylceUulose acetate. 

Ca.ta.lysts for Acetylation. Sulfuric acid is the preferred catalyst for esterifying cellulose and is the only known catalyst used commercially for this function. The role of sulfuric acid during acetylation has been discussed (77,78). In the presence of acetic anhydride, sulfuric acid rapidly and almost quantitatively forms the cellulose sulfate acid ester (77). Even in the absence of anhydride, the sulfuric acid is physically or mechanically retained (sorbed) on the cellulose. The degree of absorption is a measure of the reactivity or accessibiUty of different celluloses. 

Determining the degree of substitution using standard proton nmr refles on the integral ratio between the ceUulosic ring protons ( i 5.0-2.96) and the ester alkyl protons ( i 1.26 for butyryl and propionyl and i 2.06 for acetyl methyl groups). This simple procedure is used extensively to determine the extent of esterification and is currently the fastest, easiest way for determining the DS of mixed cellulose esters. 

Other two-dimensional techniques, such as COSY (122), DEPT (123), HOHAHA, soHd state (124) etc. give varying degrees of success when apphed to the stmcture-property relationship of cellulose triesters. The recent appHcation of multiple-bond correlation (HMBC) spectroscopy for... 

Therefore, the amount of water present determines the concentration of N02 and hence the extent of nitration. The degree of cellulose nitration is designated by the nitrogen content. The maximum commercial DS is 2.9, which corresponds to 13.8% N. Products over 14% N have been obtained by special processes (51—54). 

R wPrior to World War II, CN was produced mainly from cotton linters because of their higher degree of purity (alpha cellulose >98%). The high purity linters allowed a higher yield and better quaUty product compared to those obtained from less pure wood pulps or other cellulose sources. The development of highly purified chemical-grade wood pulps has allowed this material to be used in the same manner as are linters. 

The viscosity range of CN products can be adjusted in advance by choosing the starting cellulose with an appropriate degree of polymerization (DP). A study of the different celluloses examined the impact of various cellulose properties, such as morphological factors (percent crystallinity, fiber length, and distribution), chemical composition (DP, ash content), and hemiceUulose and lignin content, on the nitration behaviors of cellulose (55). 

---