Darts

The sequences of reactions that can follow have already been discussed in reactions (8.1) through (8.9) for APCI sources. The DART ion source may also be operated in the negative ion mode when the electrons generated in reaction (8.72) attach to molecular oxygen creating negative ions 

The ions can associate with the analyte molecule A to form adducts (reaction (8.74)), imdeigo direct electron transfer (8.75), or imdergo the solvation reactions with H2O shown in reactions 8.10 through 8.12. 

---

BE-3743 On-line quality control, production process assessment and tracking system for mechanical Darts ProT. Cerloa Fernandea UnN. Pol. Madrid... 

The DART system has been qualified according to the new regulations for ISI issued by the Swedish Nuclear Power Inspectorate. 

The DART system presented in this paper will be used for inspection of welds in Swedish nuclear power plants during 1998. 

Av wt of dart sufficient to break film in 50% of tests (ASTM D4272-90, Method A). 

Blending with LLDPE is used to upgrade the properties and improve the processing of conventional LDPE. For example, by adding 25% of ethylene—1-butene LLDPE resin with I2 of 0.5 to conventional LDPE resin, the dart impact strength of 75 p.m film is increased from 490 to 560 g, the puncture strength from 41 to 49 J /mm (770-920 ft-lbf/in.), and the tear strength from 43 to 63 N /mm (246—360 ppi). CompositionaHy uniform VLDPE resins are used in blends with HDPE, commodity LLDPE, and polypropylene (PP) (70,71,89). 

Tables 4—6 Ust ASTM methods used for the characterization of PB and PMP. A number of specialized methods were developed for testing particular articles manufactured from polyolefins several of these determine the performance of PB and PMP film, including the measurement of the film s dart impact strength and tear strength. Dart impact strength is measured by dropping a heavy dart with a round tip on a stretched film. Tear resistance, which reflects the film s resistance to tear propagation, is measured with the Ehnendorf tear tester. Two values for the tear strength are usually reported, one in the machine dkection of the film and the other in the transverse dkection. Pipes manufactured from PB are tested by pressurizing them internally with water the time-to-burst failure is determined at various temperatures (46). The standard test method for haze and luminous transmittance (ASTM D1003) is used for the measurement of PMP optical characteristics.

Most commercial processes produce polypropylene by a Hquid-phase slurry process. Hexane or heptane are the most commonly used diluents. However, there are a few examples in which Hquid propylene is used as the diluent. The leading companies involved in propylene processes are Amoco Chemicals (Standard OH, Indiana), El Paso (formerly Dart Industries), Exxon Chemical, Hercules, Hoechst, ICl, Mitsubishi Chemical Industries, Mitsubishi Petrochemical, Mitsui Petrochemical, Mitsui Toatsu, Montedison, Phillips Petroleum, SheU, Solvay, and Sumimoto Chemical. Eastman Kodak has developed and commercialized a Hquid-phase solution process. BASE has developed and commercialized a gas-phase process, and Amoco has developed a vapor-phase polymerization process that has been in commercial operation since early 1980. 

For group B and D particles, nearly all the excess gas velocity (U — U,nj) flows as bubbles tnrough the bed. The flow of bubbles controls particle mixing, attrition, and elutriation. Therefore, ehitriation and attrition rates are proportional to excess gas velocity. Readers should refer to Sec. 17 for important information and correlations on Gel-dart s powder classification, minimum fluidization velocity, bubble growth and bed expansion, and elutriation. 

Selecting the core material and style for a switching power supply application is often viewed as a dart board type of selection process by a designer starting his or her first transformer design. Although almost every core material and... 

---