Critical micelle concentration measurement

The styrene (Polysciences) was washed with 10 aqueous sodium hydroxide to remove the inhibitor and vacuum-distilled under dry nitrogen the 1-pentanol (Fisher Scientific) was dried over potassium carbonate and vacuum-distilled the potassium persulfate (Fisher Scientific) was recrystallized twice from water the 2,2 -azobls(2-methyl butyro-nltrlle) (E. I. du Pont de Nemours) was recrystallized twice from methanol the sodium dodecyl sulfate (Henkel) was used as received its critical micelle concentration measured by surface tension was 5.2 mM. Dlstllled-delonlzed water was used in all experiments. 

The concentration at which micellization commences is called the critical micelle concentration, erne. Any experimental teclmique sensitive to a solution property modified by micellization or sensitive to some probe (molecule or ion) property modified by micellization is generally adequate to quantitatively estimate the onset of micellization. The detennination of erne is usually done by plotting the experimentally measured property or response as a hmction of the logarithm of the surfactant concentration. The intersection of asymptotes fitted to the experimental data or as a breakpoint in the experimental data denotes the erne. A partial listing of experimental... 

Emulsification is the process by which a hydrophobic monomer, such as styrene, is dispersed into micelles and monomer droplets. A measure of a surfactant s abiUty to solubilize a monomer is its critical micelle concentration (CMC). Below the CMC the surfactant is dissolved ia the aqueous phase and does not serve to solubilize monomer. At and above the CMC the surfactant forms spherical micelles, usually 50 to 200 soap molecules per micelle. Many... 

An interesting change of the UV-absorbances with electrolyte concentration was observed for A18 and T18, as shown in Fig. 5. The molar extinction coefficient of A18 decreased by about 7% at 0.09 mM, and that of T18 about 10% at 0.16 mM. These concentrations may correspond to the critical micelle concentration, since the cmc observed from the surface tension measurements were about 0.1 mM for both A18 and T18. 

If the coupling component is not ionic, however, more dramatic effects occur, as found by Hashida et al. (1979) and by Tentorio et al. (1985). Hashida used N,N-bis(2-hydroxyethyl)aniline, while Tentorio and coworkers took 1-naphthylamine and l-amino-2-methylnaphthalene as coupling components. With cationic arenediazo-nium salts and addition of sodium dodecyl sulfate (SDS), rate increases up to 1100-fold were measured in cases where the surfactant concentration was higher than the critical micelle concentration (cmc). Under the same conditions the reaction... 

Table 17 shows the CMCs of sodium alcohol propoxysulfates at 20°C determined from surface tension measurements by the maximum bubble pressure [127] and Table 18 shows the critical micelle concentrations of sodium pro-poxylated octylphenol and propoxylated nonylphenol sulfates. Surface tension... 

It was mentioned previously that the narrow range of concentrations in which sudden changes are produced in the physicochemical properties in solutions of surfactants is known as critical micelle concentration. To determine the value of this parameter the change in one of these properties can be used so normally electrical conductivity, surface tension, or refraction index can be measured. Numerous cmc values have been published, most of them for surfactants that contain hydrocarbon chains of between 10 and 16 carbon atoms [1, 3, 7], The value of the cmc depends on several factors such as the length of the surfactant chain, the presence of electrolytes, temperature, and pressure [7, 14], Some of these values of cmc are shown in Table 2. 

Critical Micelle Concentration (cmc) is the surfactant concentration below which the formation of reverse micelles does not occur, while the number of surfactant molecules per micelle is referred to as the aggregation number, n. The cmc is obtained through physical measurements, and varies from 0.1-1.0 mmol dm in water or the nonpolar solvents. 

Partition coefficients of surfactants have been reported to remain constant below the critical micelle concentration (CMC), and to increase with concentration above the CMC (2,9,10). The effect of surfactant concentration in the aqueous phase (C ) on K was investigated with Makon 14 (14 mol% ethylene oxide, NPEj ), the results are given in Fig. 2. These data indicate a CMC of about O.lg/1, or 12 piM, in close agreement with the value obtained by surface tension measurements (our data and ref. 22). In subsequent determinations of Kp, C was just below the CMC to minimize the effects of micellization (15,23). 

In this experiment the degree of ionization of CTAB micelles is determined by measuring the change in slope of solution electrical conductivity (k) versus total concentration (C) as the solution goes through the critical micelle concentration (cmc). That this information is suffi-... 

The surface tension of the aqueous solution of dode-cylaitunonium chloride (DAC) — decylairanonium chloride (DeAC) mixture was measured as a function of the total molality m of surfactants and the mole fraction X of DeAC in the total surfactant in the neighborhood of the critical micelle concentration (CMC). By use of the thermodynamic equations derived previously, the mole fraction in the mixed adsorbed film was evaluated from the y vs. X and m vs. X curves. Further, the mole fraction in the mixed micelle was evaluated from the CMC vs. X curve. By comparing these values at the CMC, it was concluded that the behavior of DAC and DeAC molecules in the mixed micelle is fairly similar to that in the mixed adsorbed film. 

The anionic surfactant, sodium dodecylsulfate, SDS, was obtained from Merck, Darmstadt, Federal Republic of Germany. It has a stated purity of 99.99% and was used without further purification. Surface tension measurements gave no minimum in the surface tension at the critical micelle concentration, indicating that the sample did not contain highly surface active impurities. 

The critical micelle concentrations (cmc) of the mixed surfactant systems were determined by measuring the surface tension as a function of total surfactant concentration on a du Noiiy ring balance at 25°C. 

Test Methods. Surface tension (y) measurements were taken by Wil-helmy method (25+0.1°C). Critical micelle concentrations (cmc) were obtained from Y logC curves. Contact angle. Type GI, Japan. Wetting test. Canvas disk method, CIS,HG-2-380-66. Foam test, Ross-Miles lather method. Emulslbillty was determined by mixing 20 ml of 2.5%... 

The enthalpy change associated with formation of a thermodynamically ideal solution is equal to zero. Therefore any heat change measured in a mixing calorimetry experiment is a direct indicator of the interactions in the system (Prigogine and Defay, 1954). For a simple biopolymer solution, calorimetric measurements can be conveniently made using titra-tion/flow calorimeter equipment. For example, from isothermal titration calorimetry of solutions of bovine P-casein, Portnaya et al. (2006) have determined the association behaviour, the critical micelle concentration (CMC), and the enthalpy of (de)micellization. 

K-casein aggregates in aqueous medium are more complicated than those of p-casein, being composed of star-like sub-micelles, where each submicelle contains nine K-casein chains and the total degree of association may reach about 140 (Thum el al., 1987a). Payens and Vreeman (1982) used sedimentation measurements to infer a critical micelle concentration for K-casein of 0.5 mg/ml. 

The electrophoretic mobility of sodium dodecyl sulfate micelles was determined by the moving-boundary method after the micelles were made visible by solubilizing dye in them. This quantity was measured at the critical micelle concentration (CMC) in the presence of various concentrations of NaCl. The radius of the micelles was determined by light scatteringj... 

By measuring fluorescence intensity as a function of [Q] at fixed [S], we can find the average number of molecules of S per micelle if we know the critical micelle concentration (which is independently measured in solutions of S). The table below gives data for 3.8 (jlM pyrene in a micellar solution with a total concentration of sodium dodecyl sulfate [S] = 20.8 mM. 

Changes in surface pressure with time or concentration can be used to measure various fundamental properties. Changes in surface pressure versus protein concentration curves can be used to determine the excess surface concentration (critical micelle concentration), defined as the amount of protein at the surface divided by the surface area. Indicates minimum amount of protein needed to form an emulsion. 

The critical micelle concentration (cmc) in block copolymer solutions can be determined by measurement of the surface tension (y) as a function of concentration. The method detects completion of the Gibbs monolayer at the air/water interface, and is a secondary indicator of the onset of micellization. The cmc for solutions of monodisperse polymers is indicated by a fairly sharp decrease in y versus log(c). 

Takahashi et al.67) prepared ionene-tetrahydrofuran-ionene (ITI) triblock copolymers and investigated their surface activities. Surface tension-concentration curves for salt-free aqueous solutions of ITI showed that the critical micelle concentration (CMC) decreased with increasing mole fraction of tetrahydrofuran units in the copolymer. This behavior is due to an increase in hydrophobicity. The adsorbance and the thickness of the adsorbed layer for various ITI at the air-water interface were measured by ellipsometry. The adsorbance was also estimated from the Gibbs adsorption equation extended to aqueous polyelectrolyte solutions. The measured and calculated adsorbances were of the same order of magnitude. The thickness of the adsorbed layer was almost equal to the contour length of the ionene blocks. The intramolecular electrostatic repulsion between charged groups in the ionene blocks is probably responsible for the full extension of the... 

---