Consistency, penetration

The key to achieving a successful injection with a needle-free system is to understand the necessary mechanics for the consistent penetration of skin and fat with a liquid jet, without causing unnecessary trauma to the tissues and to the molecule being delivered. Only recently have detailed studies of the fluid mechanics of needle-free injection appeared. The fluid mechanics conditions necessary for a consistent targeted needle-free injection are addressed in the following section. 

Once the in vivo and in vitro models utilizing compromised skin are able to yield clear and consistent penetration results with materials of assorted physical and chemical properties, researchers will have the abihty to draw rehable comparisons and correlations between the two models. 

Searching for a business niche, the Brooks introduced Barnes Solids in 1979. Designed for deep, consistent penetration on dangerous game, these lead-free bullets were constructed of a solid copper/zinc alloy. 

Another method of obtaining 3D tomographic model of object consists in use of systems with 3D configuration of penetrating emission. In NDT tomographs with conic beams are the... 

The adopted approach consists in the realization of a set of standard defects holes situated at different depths in plan pieces, tungsten inclusions, lack of penetration, etc.(Figure 1,2). 

The diffraction pattern consists of a small number of spots whose symmetry of arrangement is that of the surface grid of atoms (see Fig. IV-10). The pattern is due primarily to the first layer of atoms because of the small penetrating power of the low-energy electrons (or, in HEED, because of the grazing angle of incidence used) there may, however, be weak indications of scattering from a second or third layer. 

In glassy polymers tire interactions of tire penetrant molecules witli tire polymer matrix differ from one sorjDtion site to anotlier. A limiting description of tire interaction distribution is known under tire name of tire dual-soriDtion model [, 60]. In tliis model, tire concentration of tire penetrant molecules consists of two parts. One obeys Henry s law and tire otlier a Langmuir isotlienn ... 

The technique of mercury porosimetry consists essentially in measuring the extent of mercury penetration into an evacuated solid as a function of the applied hydrostatic pressure. The full scope of the method first became apparent in 1945 when Ritter and Drake developed a technique for ... 

Acoustical Louvers. Acoustical louvers are used in building mechanical systems when exterior walls are penetrated for fresh air intake, exhaust, or rehef air, in situations where the impact of HVAC noise is of concern in the surrounding environment. The louvers consist of a series of hoUow sheet metal blades. The bottom faces of the louver blades are perforated and the blades are filled with fibrous sound-absorbing material. Typical acoustical louvers are 20 cm (8 in.) to 30 cm (12 in.) in depth. The amount of insertion loss they provide is limited. 

Electrical trees consist of visible permanent hoUow channels, resulting from decomposition of the material, and show up clearly in polyethylene and other translucent soHd dielectrics when examined with an optical microscope. Eresh, unstained water trees appear diffuse and temporary. Water trees consist of very fine paths along which moisture has penetrated under the action of a voltage gradient. Considerable force is required to effect this... 

Filtered-Particle Inspection. Solids containing extensive inteiconnected porosity, eg, sintered metallic or fired ceramic bodies formed of particles that ate typically of 0.15-mm (100-mesh) screen size, are not inspectable by normal Hquid penetrant methods. The preferred test medium consists of a suspension of dyed soHd particles, which may be contained in a Hquid vehicle dyed with a different color. Test indications can form wherever suspensions can enter cracks and other discontinuities open to the surface and be absorbed in porous material along interior crack walls. The soHd particles that form test indications ate removed by filtration along the line of the crack at the surface where they form color or fluorescent indications visible under near-ultraviolet light (1,3). 

Nonstabilized foams are referred to as froths froth-bonded fabrics are similar in properties to some saturation-bonded nonwovens. Typical foams used as nonwoven binder solutions have a consistency similar to shaving cream. AppHcation methods include knife-edge layering onto a horizontal web surface followed by vacuum penetration, and saturation and penetration of a vertical web surface using a horizontal-nip pad. Drying and curing is carried out in ovens, dmm dryers, or steam cans. 

Penetration—Indentation. Penetration and indentation tests have long been used to characterize viscoelastic materials such as asphalt, mbber, plastics, and coatings. The basic test consists of pressing an indentor of prescribed geometry against the test surface. Most instmments have an indenting tip, eg, cone, needle, or hemisphere, attached to a short rod that is held vertically. The load is controlled at some constant value, and the time of indentation is specified the size or depth of the indentation is measured. Instmments have been built which allow loads as low as 10 N with penetration depths less than mm. The entire experiment is carried out in the vacuum chamber of a scanning electron microscope with which the penetration is monitored (248). 

Ba.lla.sted. A ballasted roof assembly consists of a membrane or membrane and substrate material (insulation, sHp sheet, etc) loosely laid over a deck with the assembly held in place using ballast. A minimum ballast weight of 48.9 kg/m or 10 pounds per square foot (PSF) is used. The ballast can consist of smooth rounded stone, cmshed stone (a separator sheet must be used between the cmshed stone and the membrane), or pavers (both standard and lightweight). Both stone and pavers come in a wide variety of colors. The membrane is affixed to the building only at the deck perimeter (roof edge) and at various penetrations. Wall and penetration flashings are typically fuUy adhered and sealed to prevent water entry into the roof assembly. The maximum slope a ballasted system should be installed over is 16.7 cm/m. 

The bitumen in the Athabasca deposit, which has a gravity on the API scale of 8°, is heavier than water and very viscous. Tar sand is a dense, soHd material, but it can be readily dug in the summer months during the winter months when the temperatures plunge to —45° C, tar sand assumes the consistency of concrete. To maintain acceptable digging rates in winter, mining must proceed faster than the rate of frost penetration if not, supplemental measures such as blasting are required. 

Float Test (ASTMD139). The consistency properties of an asphalt at a very low apphed force are indicated by this test. The test is normally used for those asphalts that are too soft for the penetration test. 

Penetration (ASTMD5). This is a commonly used consistency test. It involves the deterrnination of the extent to which a standard needle penetrates a propedy prepared sample of asphalt under definitely specified conditions of temperature, load, and time. The distance that the needle penetrates in units of mm/10 measured from 0 to 300, is the penetration value. Soft asphalts have high penetration values. 

---