Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Considerations when applying device

An alternative to the rotating disk method in a quiescent fluid is a stationary disk placed in a rotating fluid. This method, like the rotating disk, is based on fluid mechanics principles and has been studied using benzoic acid dissolving into water [30], Khoury et al. [31] applied the stationary disk method to the study of the mass transport of steroids into dilute polymer solutions. Since this method assumes that the rotating fluid near the disk obeys solid body rotation, the stirring device and the distance of the stirrer from the disk become important considerations when it is used. A similar device was developed by Braun and Parrott [32], who used stationary spherical tablets in a stirred liquid to study the effect of various parameters on the mass transport of benzoic acid. [Pg.114]

The optical detection methods applied to microchip-based analysis are, for the most part, similar to those employed in capillary electrophoresis (CE). The main differences, however, are that UV absorbance is not as common and that the microchip format creates the possibility of incorporating additional functionality during the fabrication steps (especially in plastic devices). Each of the optical methods described here includes specific requirements, such as the nature of the analyte and the microchip substrate, and these must be taken into consideration when choosing and implementing a system. [Pg.1254]

The detrimental effect of stresses induced by an applied load substantially increases with the loading configuration (other than single wheel load), at rest or during movement. The impact may also be considerable when the adjacent slabs that make up the pavement are non-flushed with each other. To handle this impact, the transverse joints provided have effective load transfer devices such as dowels. [Pg.594]

Table A. 2 in lEC 60079-11 for cable parameters may be referred to. Special calculations and considerations are applied for system analysis because of cable faults—especially when multicore cables (see lEC 60079-14 for type A and B cables in connection with multicore cables) are used in the installations [33]. Other important issues here are that (1) voltage drop across the resistor under normal operating conditions has to be taken into account in the design so that there is sufficient voltage at the field device and (2) Zener barriers are properly earthed as shown because without an IS earth they are not safe. To obtain independence from... Table A. 2 in lEC 60079-11 for cable parameters may be referred to. Special calculations and considerations are applied for system analysis because of cable faults—especially when multicore cables (see lEC 60079-14 for type A and B cables in connection with multicore cables) are used in the installations [33]. Other important issues here are that (1) voltage drop across the resistor under normal operating conditions has to be taken into account in the design so that there is sufficient voltage at the field device and (2) Zener barriers are properly earthed as shown because without an IS earth they are not safe. To obtain independence from...
The ideal variable to measure is one that can be monitored easily, inexpensively, quickly, and accurately. The variables that usually meet these qualifications are pressure, temperature, level, voltage, speed, and weight. When possible the values of other variables are obtained from measurements of these variables. For example, the flow rate of a stream is often determined by measuring the pressure difference across a constriction in a pipeline. However, the correlation between pressure drop and flow is also affected by changes in fluid density, pressure, and composition. If a more accurate measurement is desired the temperature, pressure, and composition may also be measured and a correction applied to the value obtained solely from the pressure difference. To do this would require the addition of an analog or digital computer to control scheme, as well as additional sensing devices. This would mean a considerable increase in cost and complexity, which is unwarranted unless the increase in accuracy is demanded. [Pg.162]

When the commercial OMA (Model 1205, Princeton Applied Research Corporation, Princeton, NJ) became available, we recognized its potential as a replacement for the photomultiplier detector. The vidicon detector surface was divided into 500 channels, the image could be seen on a cathode ray tube (CRT) monitor in real time, the intensity profile was available in digital form, the profile could be time-averaged for any desired number of video scans, and the final profile was stored in internal memory for transfer to an external output device. Not only had a considerable amount of work gone into its development and the verification of performance, but its potential for use for a variety of physical techniques would ensure the construction of enough units to support further development of the system. Moreover the need for low-light-level detectors for other purposes would lead to further improvements in detector devices. [Pg.322]

The photochemistry of small molecule LC materials has been an active area of research for many years and has been reviewed recently [9]. The photochemistry of LC polymers, per se, has received much less attention although two brief reviews have appeared [5,10], and there has been a considerable effort to apply some simple photochemical transformations such as trans-cis photoisomerization, to the development of practical devices [1-6]. This section is divided into three parts. In Part A, chromophore aggregation, which seems to be important in almost all the cases in which careful UV-Vis and/or fluorescence studies of films of pure LC polymers have been made, is explicitly discussed. Part B is devoted to a thorough review, organized by chromophore type, of the photochemistry and related photophysics of LC polymers. No attempt has been made to extensively cross-reference the work on LC polymers to the hundreds of papers and reviews on analogous non-LC compounds. However, when it seemed particularly appropriate or interesting, experiments related to optical applications of the photochemistry of LC polymers are briefly described. In Part C, a few experiments are described in which a classical photophysical method, fluorescence spectroscopy, is used to probe the microstructures of some LC polymers. [Pg.136]


See other pages where Considerations when applying device is mentioned: [Pg.427]    [Pg.321]    [Pg.202]    [Pg.567]    [Pg.235]    [Pg.344]    [Pg.237]    [Pg.172]    [Pg.142]    [Pg.386]    [Pg.493]    [Pg.926]    [Pg.865]    [Pg.215]    [Pg.145]    [Pg.221]    [Pg.20]    [Pg.354]    [Pg.519]    [Pg.474]    [Pg.109]    [Pg.2]    [Pg.98]    [Pg.130]    [Pg.83]    [Pg.107]    [Pg.511]    [Pg.97]    [Pg.205]    [Pg.1017]    [Pg.1467]    [Pg.244]    [Pg.128]    [Pg.624]    [Pg.56]    [Pg.167]    [Pg.247]    [Pg.293]    [Pg.385]    [Pg.47]    [Pg.109]    [Pg.333]    [Pg.80]   
See also in sourсe #XX -- [ Pg.216 ]




SEARCH



Considerations when applying

Devices considerations

© 2024 chempedia.info