Conducting polymer additives

Permanent antistats do not depend on the relative humidity and they do not lose their effectiveness in a short time. One type is exemplified by the use of polyether-polyamide block copolymers combined with an intrinsically conducting substance, and another class consists of neoalkoxytitanates or zirconates. These compounds form non-blooming, bipolar layers, producing a surface and volume electron-transfer circuit, which produces a permanent antistatic effect. They are independent of atmospheric moisture and compatible with a wide range of polymers, including polyolefins, polyesters, polystyrene and PVC. Inherently conducting polymer additives such as sulfonated polyanilines are also used. They are discussed further in Chapter 5. 

Conducting fillers for plastics (2) Conducting polymer additives Fillers ... 

In addition to conventional applications in conducting polymers and electrooptical devices, a number of recent novel applications have emerged. Switching of DNA electron transfer upon single-strand/double-strand hybridization fonns the basis for a new medical biosensor teclmology. Since the number of base pairs of length 20... 

More recently, Raman spectroscopy has been used to investigate the vibrational spectroscopy of polymer Hquid crystals (46) (see Liquid crystalline materials), the kinetics of polymerization (47) (see Kinetic measurements), synthetic polymers and mbbers (48), and stress and strain in fibers and composites (49) (see Composite materials). The relationship between Raman spectra and the stmcture of conjugated and conducting polymers has been reviewed (50,51). In addition, a general review of ft-Raman studies of polymers has been pubUshed (52). 

Practical appHcations have been reported for PVP/ceUulosics (108,119,120) and PVP/polysulfones (121,122) in membrane separation technology, eg, in the manufacture of dialysis membranes. Electrically conductive polymers of polyaruline are rendered more soluble and hence easier to process by complexation with PVP (123). Addition of small amounts of PVP to nylon 66 and 610 causes significant morphological changes, resulting in fewer but more regular spherulites (124). 

There are different concrete replacement systems available for renovating reinforced concrete structures. They range from sprayed concrete without polymer additions to systems containing conducting polymers (PCC-mortar). Since with the latter alkalinity is lower, more rapid carbonization occurs on weathering [59] and the increased electrical resistivity has to be taken into account, so that with cathodic protection only sprayed concrete should be used as a repair mortar. 

The first use of ionic liquids in free radical addition polymerization was as an extension to the doping of polymers with simple electrolytes for the preparation of ion-conducting polymers. Several groups have prepared polymers suitable for doping with ambient-temperature ionic liquids, with the aim of producing polymer electrolytes of high ionic conductance. Many of the prepared polymers are related to the ionic liquids employed for example, poly(l-butyl-4-vinylpyridinium bromide) and poly(l-ethyl-3-vinylimidazolium bis(trifluoromethanesulfonyl)imide [38 1]. 

Equations (37) and (38), along with Eqs. (29) and (30), define the electrochemical oxidation process of a conducting polymer film controlled by conformational relaxation and diffusion processes in the polymeric structure. It must be remarked that if the initial potential is more anodic than Es, then the term depending on the cathodic overpotential vanishes and the oxidation process becomes only diffusion controlled. So the most usual oxidation processes studied in conducting polymers, which are controlled by diffusion of counter-ions in the polymer, can be considered as a particular case of a more general model of oxidation under conformational relaxation control. The addition of relaxation and diffusion components provides a complete description of the shapes of chronocoulograms and chronoamperograms in any experimental condition ... 

The results from EQCM studies on conducting polymer films can be ambiguous because the measured mass change results from a combination of independent ion transport, coupled ion transport (i.e., salt transport), and solvent transport. In addition, changes in the viscoelasticity of the films can cause apparent mass changes. The latter problem can be minimized by checking the frequency response of the EQCM,174 while the various mass transport components can be separated by careful data analysis.175,176... 

Intensive research on the electrocatalytic properties of polymer-modified electrodes has been going on for many years Until recently, most known coatings were redox polymers. Combining redox polymers with conducting polymers should, in principle, further improve the electrocatalytic activity of such systems, as the conducting polymers are, in addition, electron carriers and reservoirs. One possibility of intercalating electroactive redox centres in the conducting polymer is to incorporate redoxactive anions — which act as dopants — into the polymer. Most research has been done on PPy, doped with inter alia Co 96) RyQ- 297) (--q. and Fe-phthalocyanines 298,299) Co-porphyrines Evidently, in these... 

Meanwhile, the R-R coupling (see Sect. 2.2) has evidently found general acceptance as the main reaction path for the electropolymerization of conducting polymers The ionic character of the coupling species explains why polar additives such as anions or solvents with high permittivity accelerate the rate of polymerization and function as catalysts. Thus, electropolymerization of pyrrole is catalyzed in CHjCN by bromide ions or in aqueous solution by 4,5-dihydro-1,3-benzenedisulfonic acid The electrocatalytic influence of water has been known since the work... 

For this reason, other types of electrolytes are used in addition to aqueous solutions (i.e., nonaqueous solutions of salts (Section 8.1), salt melts (Section 8.2), and a variety of solid electrolytes (Section 8.3). More recently, a new type of solid electrolyte is being employed more often (i.e., water-impregnated ionically conducting polymer films more about them in Chapter 26). 

All this, in summary, would amount to additional sections on conductive polymers and to a future chapter on semiconductive polymers, currently representing an encouraging outlook for a journey begun in serendipity. 

Principles and Characteristics A substantial percentage of chemical analyses are based on electrochemistry, although this is less evident for polymer/additive analysis. In its application to analytical chemistry, electrochemistry involves the measurement of some electrical property in relation to the concentration of a particular chemical species. The electrical properties that are most commonly measured are potential or voltage, current, resistance or conductance charge or capacity, or combinations of these. Often, a material conversion is involved and therefore so are separation processes, which take place when electrons participate on the surface of electrodes, such as in polarography. Electrochemical analysis also comprises currentless methods, such as potentiometry, including the use of ion-selective electrodes. 

Another example of ion conducting polymer/ion/solvent systems are polyelectrolytes based on ion-exchange polymers, also called ionomers. The ionic conductivity of ion-exchange polymers is usually very low in the dry state, but increases abruptly by orders of magnitude upon addition of a... 

---