Cladding absorption

To gain insight into the mechanism responsible for cladding absorption, we treat the ray as a plane wave in localized regions about a reflection or turning... 

The power attenuation coefficient for cladding absorption is found either by averaging T over the ray half-period between successive reflections or... 

When both the core and cladding materials of a fiber are absorbing, the power attenuation coefficient y for a ray is given by the sum of the core and cladding absorption coefficients. Hence... 

Eqs. (6-26b) and (6-28). Numerical evaluation of Eq. (8-39) for a fiber with V = 50, 0 =O.14 and = l(X)dB/km leads to the curves in Fig. 8-11(b) [10]. The characteristic behavior of the curves is similar to that for the step profile, but the effect of the cladding absorption is very much reduced because most ray paths have turning points well away from the interface. 

Hafnium tetrafluoride [13709-52-9] is one component in the cladding layer of a proposed zirconium fluoride glass optical waveguide fiber composition which is expected to have a lower intrinsic light absorption than fused quart2 optical fiber (see Glass Fiber optics Fluorine compounds, inorganic-zirconium). 

Off-Gas Treatment. Before the advent of the shear, the gases released from the spent fuel were mixed with the entire dissolver off-gas flow. Newer shear designs contain the fission gases and provide the opportunity for more efficient treatment. The gaseous fission products krypton and xenon are chemically inert and are released into the off-gas system as soon as the fuel cladding is breached. Efficient recovery of these isotopes requires capture at the point of release, before dilution with large quantities of air. Two processes have been developed, a cryogenic distillation and a Freon absorption. 

The fifth component is the stmcture, a material selected for weak absorption for neutrons, and having adequate strength and resistance to corrosion. In thermal reactors, uranium oxide pellets are held and supported by metal tubes, called the cladding. The cladding is composed of zirconium, in the form of an alloy called Zircaloy. Some early reactors used aluminum fast reactors use stainless steel. Additional hardware is required to hold the bundles of fuel rods within a fuel assembly and to support the assembhes that are inserted and removed from the reactor core. Stainless steel is commonly used for such hardware. If the reactor is operated at high temperature and pressure, a thick-walled steel reactor vessel is needed. 

Because of its low neutron absorption, zirconium is an attractive stmctural material and fuel cladding for nuclear power reactors, but it has low strength and highly variable corrosion behavior. However, ZircaHoy-2, with a nominal composition of 1.5 wt % tin, 0.12 wt % iron, 0.05 wt % nickel, 0.10 wt % chromium, and the remainder zirconium, can be used ia all nuclear power reactors that employ pressurized water as coolant and moderator (see... 

Properties. Most of the alloys developed to date were intended for service as fuel cladding and other stmctural components in hquid-metal-cooled fast-breeder reactors. AHoy selection was based primarily on the following criteria corrosion resistance in Hquid metals, including lithium, sodium, and NaK, and a mixture of sodium and potassium strength ductihty, including fabricabihty and neutron considerations, including low absorption of fast neutrons as well as irradiation embrittlement and dimensional-variation effects. Alloys of greatest interest include V 80, Cr 15, Ti 5... 

Hafnium-free zirconium is particularly weU-suited for these appHcations because of its ductiHty, excellent oxidation resistance in pure water at 300°C, low thermal neutron absorption, and low susceptibiHty to radiation. Nuclear fuel cladding and reactor core stmctural components are the principal uses for zirconium metal. 

Silver halide fibres (AgClxBri x) have the widest spectral range in the mid-IR, well into the fingerprint range. Due to their crystalline nature, they have a superior flexibility. Problematic is their tendency to decompose upon contact with UV radiation or base metals. Also sulphides will chemically destroy the fibre material. Other points against are the high intrinsic attenuation due to absorption by impurities or scattering at inclusions or micro-crystals and the non-availability of (applicable) core-clad fibres. 

TMM handles thin metallic films as well, as they are used in lO-sensors based on surface-plasmon-polaritons (SPP). SPPs appear at the dielectric-metal interface for TM polarization, exclusively. The sensor principle is to have a waveguide mode and the SPP close to resonance, and screen the resonance vs. angle or vs. wavelength to detect refractive index changes of the cladding. Figure 4 shows the resonance of the absorption vs. the... 

---