Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Thermal aqueous liquid chromatography

With an increased interest and awareness of the impact of society and industry on the environment, there has been a significant attempt in recent years to reduce or replace the usage of organic solvents. Much early work in this area concentrated on the application of supercritical and subcritical carbon dioxide, but in recent years superheated (or subcritical/pressurized hot) water (SHW) has become of interest for both chromatography and extraction [43,54], The earliest work was reported by GuUlemin et al. [55], who used the term thermal aqueous liquid chromatography. As well as using SHW for the separation of... [Pg.821]

C. L. Guillemin, J. L. Miller, and J. Dubois, Thermal Aqueous liquid chromatography—The TALC Technique, JHRC and CC 4 (1981), 280-286. [Pg.833]

C30 oil, homopolymer of 1-decene, Ethyl Corp., Inc.) served as the start-up solvent for the experiments. The catalyst (ca. 5-8 g) was added to start-up solvent (ca. 300 g) in the CSTR. The reactor temperature was then raised to 270°C at a rate of l°C/min. The catalyst was activated using CO at a space velocity of 3.0 sl/h/g Fe at 270°C and 175 psig for 24 h. FTS was then started by adding synthesis gas mixture (H2 CO ratio of 0.7) to the reactor at a space velocity of either 3.1 or 5.0 sl/h/g Fe. The conversions of CO and H2 were obtained by gas chromatography (GC) analysis (HP Quad Series Micro-GC equipped with thermal conductivity detectors) of the product gas mixture. The reaction products were collected in three traps maintained at different temperatures—a hot trap (200°C), a warm trap (100°C), and a cold trap (0°C). The products were separated into different fractions (rewax, wax, oil, and aqueous) for quantification by GC analysis. However, the oil and the wax (liquid at room temperature) fractions were mixed prior to GC analysis. [Pg.122]

Leeuwenkamp OR, van der Mark EJ, van Bennekom WP, Bult A. Investigation of the photochemical and thermal degradation of aqueous nitroprusside solution using liquid chromatography. Int J Pharm 1985 24 27 H. [Pg.357]

Solid-phase microextraction (SPME) — is a procedure originally developed for sample preconcentration in gas chromatography (GC). In this procedure a small-diameter fused silica optical fiber, coated with a liquid polymer phase such as poly(dimethylsiloxane), is immersed in an aqueous sample solution. The -> analytes partition into the polymer phase and are then thermally desorbed in the GC injector on the column. The same polymer coating is used as a stationary phase of capillary GC columns. The extraction is a non-exhaustive liquid-liquid extraction with the convenience that the organic phase is attached to the fiber. This fiber is contained in a syringe, which protects it and simplifies introduction of the fiber into a GC injector. Both uncoated and coated fibers with films of different GC stationary phases can be used. SPME can be successfully applied to the analysis of volatile chlorinated organic compounds, such as chlorinated organic solvents and substituted benzenes as well as nonvolatile chlorinated biphenyls. [Pg.617]

Solid-phase microextraction (SPME) is a technique that was first reported by Louch et al. in 1991 (35). This is a sample preparation technique that has been applied to trace analysis methods such as the analysis of flavor components, residual solvents, pesticides, leaching packaging components, or any other volatile organic compounds. It is limited to gas chromatography methods because the sample must be desorbed by thermal means. A fused silica fiber that was previously coated with a liquid polymer film is exposed to an aqueous sample. After adsorption of the analyte onto the coated fiber is allowed to come to equilibrium, the fiber is withdrawn from the sample and placed directly into the heated injection port of a gas chromatograph. The heat causes desorption of the analyte and other components from the fiber and the mixture is quantitatively or qualitatively analyzed by GC. This preparation technique allows for selective and solventless GC injections. Selectivity and time to equilibration can be altered by changing the characteristics of the film coat. [Pg.91]


See other pages where Thermal aqueous liquid chromatography is mentioned: [Pg.336]    [Pg.791]    [Pg.915]    [Pg.46]    [Pg.4]    [Pg.102]    [Pg.473]    [Pg.27]    [Pg.291]    [Pg.48]    [Pg.944]    [Pg.80]    [Pg.280]    [Pg.374]    [Pg.239]    [Pg.78]    [Pg.529]    [Pg.621]    [Pg.507]    [Pg.131]    [Pg.3]    [Pg.492]    [Pg.251]    [Pg.510]    [Pg.1300]    [Pg.280]    [Pg.196]    [Pg.318]    [Pg.319]    [Pg.95]    [Pg.875]    [Pg.10]    [Pg.130]    [Pg.223]   
See also in sourсe #XX -- [ Pg.821 ]




SEARCH



Aqueous Chromatography

Aqueous liquids

Chromatography, thermal

Thermal aqueous liquid

© 2024 chempedia.info