Chloride minerals formation

The examples in the preceding section, of the flotation of lead and copper ores by xanthates, was one in which chemical forces predominated in the adsorption of the collector. Flotation processes have been applied to a number of other minerals that are either ionic in type, such as potassium chloride, or are insoluble oxides such as quartz and iron oxide, or ink pigments [needed to be removed in waste paper processing [92]]. In the case of quartz, surfactants such as alkyl amines are used, and the situation is complicated by micelle formation (see next section), which can also occur in the adsorbed layer [93, 94]. 

Phenylhydrazine is, however, frequently supplied in the form of its hydro chloride or sulphate, since these salts on exposure to light darken less rapidly than the free base. If these salts are used, however, osazone formation is unsatisfactory, partly because the mineral acid formed by hydrolysis of... 

The ore is ordinarily ground to pass through a ca 1.2-mm (14-mesh) screen, mixed with 8—10 wt % NaCl and other reactants that may be needed, and roasted under oxidising conditions in a multiple-hearth furnace or rotary kiln at 800—850°C for 1—2 h. Temperature control is critical because conversion of vanadium to vanadates slows markedly at ca 800°C, and the formation of Hquid phases at ca 850°C interferes with access of air to the mineral particles. During roasting, a reaction of sodium chloride with hydrous siUcates, which often are present in the ore feed, yields HCl gas. This is scmbbed from the roaster off-gas and neutralized for pollution control, or used in acid-leaching processes at the mill site. 

Severe concentration cell corrosion involves segregation of aggressive anions beneath deposits. Concentrations of sulfate and chloride, in particular, are deleterious. Acid conditions may be established beneath deposits as aggressive anions segregate to these shielded regions. Mineral acids, such as hydrochloric and sulfuric, form by hydrolysis. The mechanism of acid formation is discussed in Chap. 2. 

Many salts and minerals display an enhanced tendency to decompose and dissolve by processes involving complex ion formation and chloride acts as a ligand in these complexes. Lead sulfate has a poor solubility in water. However, in the presence of chloride ions, a complex chloroplumbate ion is formed and thereby solubility is enhanced. The relevant reactions are ... 

The effect of mineral and organic soil constituents on the mineralisation of LAS, AE, stearyl trimethylammonium chloride (STAC) and sodium stearate (main soap component) in soils was studied by Knaebel and co-workers [38]. The four 14C-labelled compounds were aseptically adsorbed to montmorillonite, kaolinite, illite, sand and humic acids and subsequently mixed with soil yielding surfactant concentrations of about 50 jig kg-1. The CO2 formation in the serum bottle respirometers was monitored over a period of 2 months indicating that the mineralisation extent was highest for LAS (49-75%). Somewhat lower amounts of produced CO2 were reported for AE and the stearate ranging from 34-58% and 29-47%, respectively. The mineralisation extent of the cationic surfactant did not exceed 21% (kaolinite) and achieved only 7% in the montmorillonite-modified soil. Associating the mineral type with the mineralisation kinetics showed that sand... 

Dinitrocubane (28) has been synthesized by Eaton and co-workers via two routes both starting from cubane-l,4-dicarboxylic acid (25). The first of these routes uses diphenylphos-phoryl azide in the presence of a base and tert-butyl alcohol to effect direct conversion of the carboxylic acid (25) to the tert-butylcarbamate (26). Hydrolysis of (26) with mineral acid, followed by direct oxidation of the diamine (27) with m-CPBA, yields 1,4-diiutrocubane (28). Initial attempts to convert cubane-l,4-dicarboxylic acid (25) to 1,4-diaminocubane (27) via a Curtins rearrangement of the corresponding diacylazide (29) were abandoned due to the extremely explosive nature of the latter. However, subsequent experiments showed that treatment of the acid chloride of cubane-l,4-dicarboxylic acid with trimethylsilyl azide allows the formation of the diisocyanate (30) without prior isolation of the dangerous diacylazide (29) from solution. Oxidation of the diisocyanate (30) to 1,4-dinitrocubane (28) was achieved with dimethyldioxirane in wet acetone. Dimethyldioxirane is also reported to oxidize both the diamine (27) and its hydrochloride salt to 1,4-dinitrocubane (28) in excellent yield. ... 

The usual procedure of preparing acid azides, which involves treating an acid chloride with sodium azide,8,9 suffers from the disadvantage that it is often difficult to obtain pure acid chlorides in good yields from acids which either decompose or undergo isomerization in the presence of mineral acids.7 Synthesis of the azide by way of the ester and hydrazide10 has been used to circumvent this difficulty but is much less convenient. The present procedure permits ready formation of acid azides in excellent yields from mixed carboxylic-carbonic anhydrides and sodium azide under very mild conditions. 

---