CE designation

Leren ce Limbe rs design s design s al designs ce designs situatio ns ns desig ns pages calculation s and analysis number of references leve emphas... 

HgPh2 remaining after each rnn. Cumulated amount of products at the end of each rim Ph - Ph, Ph - Chxa, Ce designate biphenyl, phenylcyclohexane and the sum of benzene/cyclohexane respectively. Hgf and Phf correspond to the mass balance in Hg and organic componnds, respectively. 

CEN-227, Summary Report on the Operability of Pressurizer Safety Relief Valves in CE Designed Plants , Combustion Engineering, Inc, December 1982. 

Small size, ruggedness, simple cabling and the ability to operate the equipment under adverse conditions in the field has also been design goals. The system should also conform with the regulations necessary for the CE-marking (i. e. standards and directives for EMC, Electrical Safety and Machine Safety). 

Technical requirements Sound engineering practice, essential requirements tarticle 3t The directive includes a particular technical requirement with respect to equipment which presents only a minor pressure hazard. For such equipment the essential requirements and the certification procedures are not applicable. Instead the so-called sound engineering practice of one of the Member States must be applied. That practice must ensure that design and manufacture takes into account all relevant factors influencing safety during the intended lifetime. The equipment must be accompanied with adequate instruetions for use and must bear the identification of the manufacturer. The CE-marking shall not be applied for such equipment. 

The design and testing of these developmental plants are well underway. The evolutionary designs have received final design approval from the U.S. NRC. As of 1995 evolutionary ALWR designs very similar to these, by the same U.S. manufacturers, are already being built in Asia the GE-Advanced BWR in Japan and the ABB-CE System 80+ PWR in South Korea. The N-4 PWR is under constmction in Prance, and the SizeweU PWR has completed constmction and has initiated operation in the U.K. 

Air-Cooled Overhead Condensers Air-cooled overhead condensers (AOC) have been designed and installed above distiUation columns as integral parts of distiUation systems. The condensers generally have incliued tubes, with air flow over the finned sur ces induced by a fan. PrevaUing wind affec ts both structural design and performance. 

The fault ctirrents also develop electrodynamic foi ces, Fii, as in equation (28.4) due to the sub-transient d.c. component. These forces play an important role in the meehanical design of the interrupting device, the load-bearing and mounting structuies for the interrupter and the bus system, and the hardware used in a switchgear assembly. All such mechanical parts, supports and hardw-are should be adequate to withstand such forces when they arise, A procedure to arrive at the ideal size of the current-carrying components, mounting structure, type of supports and hardware cte, is discussed in detail in Example 28.12. 

The CE plants use U-tube steam generators with mixed capability to establish feed-and-bleed cooling. . Several CE plants are designed without pressurizer power-operated valves. The RCPs are a By WesI ise... 

In considering the applicability of preparative classical electrophoretic methods to chiral separations, it should be noted that practitioners in the art of classical electrophoresis have been particularly inventive in designing novel separation strategies. For instance, pH, ionic strength and density gradients have all been used. Isoelectric focusing and isotachophoresis are well-established separation modes in classical electrophoresis and are also being implemented in CE separations [7, 8]. These trends are also reflected in the preparative electrophoretic approaches discussed here. 

CE Service typical of certain turbocharged or supercharged heavy-duty diesel engines operating under both low speed-high load and high speed-low load conditions. Oils designed for this service must also meet the requirements specified for CC and CD classifications. 

Ce terme designe la proportion de gaz initial en place qui peut etre r cuperee dans les conditions techniques et 6conomiques actuelles. 

Some periodic charts designate the elements Ce-Lu as the /block. In this book, the elements La-Yb are designated as the /block, because Lu matches the properties of the elements in Group 3 better than La does. 

Matthews DA, Dragovich PS, Webber SE, Fuhrman SA, Patick AK, Zalman LS, Hendrickson TF, Love RA, Prins TJ, Marakovits JT, Zhou R, Tikhe J, Ford CE, Meador JW, Ferre RA, Brown EL, Binford SL, Brothers MA, DeLisle DM, Worland ST (1999) Structure-assisted design of mechanism-based irreversible inhibitors of human rhinovirus 3C protease with potent antiviral activity against multiple rhinovirus serotypes. Proc Natl Acad Sci USA 96 11000-11007... 

In our design, divalent Ca was chosen to partially substitute the trivalent atoms, and La and Ce were selected for a trivalent element because their ionic size (rLas+ = l.SOA rce3+=l-48A) was close to that of Ca (rca2+ = T48A) [21]. Like La, the Ce element also generally shows a formal -i-3 oxidation state in in-termetallics. Erom the reactions of the elements, we have identified as major phases the electron-precise/deficient alloys, Ln5.xCaxGe4 (Ln=La, Ce x=3.37,... 

The University of Georgia College of Pharmacy designates this on-line educational series for a maximum of 170 contact hours (17.0 CEUs). A Request for CE must be made for EACH offering and continuing education credit will be awarded and statements issued on-line for successful completion of materials and assessment. 

Hyphenation in capillary electrophoresis is still in its infancy. Critical aspects of CE hyphenation include the minute volumes of sample injected (typically a few nL) and small flow-rates (in the order of nLmin-1). Interfaces are not commercially available. CZE-UV can be used for the analysis of higher polyamide oligomers in HF1P solution [859]. A solvent elimination design with nebuliser has been described for CE-FTIR and CEC-FTIR coupling absolute detection limits are hundreds of pg [860]. An advantage of CE-FTIR is that analytes may be detected and identified without derivatisation. CE(C)-NMR [861-863] is advancing rapidly. 

---