Carbon nanotubes ratio

It is widely perceived that carbon nanotubes will allow construction of composites with extraordinary strength weight ratios, due to the inherent strength of the nanotubes. Several rules of thumb have been developed in the study of fiber/matrix composites. Close inspection of these shows that carbon nanotubes satisfy several criteria, but that others remain untested (and therefore unsatisfied to date). High-strength com-... 

Fillers with extremely high aspect ratios (1000-10,000) such as carbon nanotubes (Figure 32.5) have a much lower percolation threshold (lower amount is required for equivalent reinforcement). 

Xin and co-workers modified the alkaline EG synthesis method by heating the metal hydroxides or oxides colloidal particles in EG or EG/water mixture in the presence of carbon supports, for preparing various metal and alloy nanoclusters supported on carbon [20-24]. It was found that the ratio of water to EG in the reaction media was a key factor influencing the average size and size distribution of metal nanoparticles supported on the carbon supports. As shown in Table 2, in the preparation of multiwalled carbon nanotube-supported Pt catalysts... 

The future remains bright for the use of carbon materials in batteries. In the past several years, several new carbon materials have appeared mesophase pitch fibers, expanded graphite and carbon nanotubes. New electrolyte additives for Li-Ion permit the use of low cost PC based electrolytes with natural graphite anodes. Carbon nanotubes are attractive new materials and it appears that they will be available in quantity in the near future. They have a high ratio of the base plane to edge plain found in HOPG. The ultracapacitor application to deposit an electronically conductive polymer on the surface of a carbon nanotube may be the wave of the future. 

Multiwall carbon nanotubes (MWCNTs) have been synthesized by catalytic chemical vapor deposition (CCVD) of ethylene on several mesoporous aluminosilicates impregnated with iron. The aluminosilicates were synthesized by sol-gel method optimizing the Si/Al ratios from 6 to 80. The catalysts are characterized by nitrogen adsorption, X-ray diffraction, 27A1 NMR, thermogravimetric analysis (TGA) and infrared. The MWCNTs are characterized by TGA and transmission and scanning electron microscope. 

The mechanical properties of the inorganic nanotubes have only been investigated to a relatively small extent. The Young s modulus of multiwall BN nanotubes was measured using the vibrational method within a TEM (17) and was found to be 1.2 TPa, which is comparable to the values measured for carbon nanotubes. The Young s modulus of the b-P nanotubes was calculated (88a). The observed value, 300 GPa, is some 25% of the Young s modulus of carbon nanotubes. The Poisson ratio of b-P nanotubes was calculated to be 0.25 in this work. 

CNTs may consist of just one layer (i.e. single-walled carbon nanotubes, SWCNTs), two layers (DWCNTs) or many layers (MWCNTs) and per definition exhibit diameters in the range of 0.7 < d < 2 nm, 1 < d < 3 nm, and 1. 4 < d < 150 nm, respectively. The length of CNTs depends on the synthesis technique used (Section 1.1.4) and can vary from a few microns to a current world record of a few cm [16]. This amounts to aspect ratios (i.e. length/diameter) of up to 107, which are considerably larger than those of high-performance polyethylene (PE, Dyneema). The aspect ratio is a crucial parameter, since it affects, for example, the electrical and mechanical properties of CNT-containing nanocomposites. 

Thus, carbon nanotubes are naturally of interest due to their very large aspect ratio, h/r. 

Nanocarbon emitters behave like variants of carbon nanotube emitters. The nanocarbons can be made by a range of techniques. Often this is a form of plasma deposition which is forming nanocrystalline diamond with very small grain sizes. Or it can be deposition on pyrolytic carbon or DLC run on the borderline of forming diamond grains. A third way is to run a vacuum arc system with ballast gas so that it deposits a porous sp2 rich material. In each case, the material has a moderate to high fraction of sp2 carbon, but is structurally very inhomogeneous [29]. The material is moderately conductive. The result is that the field emission is determined by the field enhancement distribution, and not by the sp2/sp3 ratio. The enhancement distribution is broad due to the disorder, so that it follows the Nilsson model [26] of emission site distributions. The disorder on nanocarbons makes the distribution broader. Effectively, this means that emission site density tends to be lower than for a CNT array, and is less controllable. Thus, while it is lower cost to produce nanocarbon films, they tend to have lower performance. 

Carbon nanotubes are hollow carbon cylinders with hemispherical endcaps of less than 1 nm to a few nanometres in diameter and several microns in length. The aspect ratios are of the order of 1000 and more. The elementary nanotubes agglomerate in bundles or ropes that are difficult to disperse. 

While carbon fiber (thickness on the order of 1000 nm) composites offer very strong materials, carbon nanotubes make even stronger composites. These carbon nanotubes have aspect ratios of over 1000 (ratio of length to diameter). Further, because some carbon nanotubes are electrically conductive, composites containing them can be made to be conductive. A number of carbon nanotube matrixes have been made including using a number of engineering resins, such as polyesters, nylons, polycarbonates, and PPE. 

---