Calcium sulfate Density

The formulation of calcium chelate materials is based upon the formation of a low-solubiUty chelate between calcium hydroxide and a sahcylate. Dycal utilizes the reaction product of a polyhydric compound and sahcyhc acid. Other sahcyhc acid esters can be similarly used. Vehicles used to carry the calcium hydroxide, extenders, and fillers may include mineral oil, A/-ethyl- -toluenesulfonamide [80-39-7] and polymeric fluids. The filler additions may include titanium dioxide [13463-67-7] zinc oxide, sihca [7631-86-9], calcium sulfate, and barium sulfate [7727-43-7]. Zinc oxide and barium sulfate are useflil as x-ray opacifying agents to ensure a density greater than that of normal tooth stmcture. Resins, rosin, limed rosins, and modified rosins may serve as modifiers of the physical characteristics in both the unset and set states. 

Anhydrous calcium sulfate is a crystalline substance orthorhombic the color may vary as white, gray, blue or brick-red occurs as insoluble anhydrite or porous soluble anhydrite density 2.96 g/cm hardness 3.5 Mohs insoluble anhydrite is practically insoluble in water (0.21% at 20°C) soluble anhydrite readily absorbs moisture and is soluble in water. 

The degree to which FGD scrubber material is treated influences its physical properties. Basic physical properties include solids content, moisture content, specific gravity, and wet and dry density [67]. When dewatered, the calcium sulfite FGD sludges become a soft filter cake with a solids content typically in the 40-65% range. Calcium sulfate FGD sludges can be dewatered much more easily and may achieve solid contents as high as 70-75% after dewatering [67]. 

Liver starch. See Glycogen Liver of sulfur. See Sulfurated potash LLDPE. See Polyethylene, linear low density LMB. See Lauryl betaine LMS-152. See (Chloropropyl) methylsiloxane-dimethylsiloxane copolymer LNG. See Methane gas Lobase C-4501. See Calcium sulfate Lobra 70. See Hydrogenated canola oil Lobra RBD. See Canola oil Lobra. See Hydrogenated canola oil Locron L, P, S. See Aluminum chlorohydrate Locust bean (Ceratonia siliqua) gum CAS 9000-40-2 EINECS/ELINCS 232-541-5 FEMA 2648 INS410 E410 Synonyms Algaroba Carob bean gum Carob flour Carob gum Ceratonia Ceratonia siliqua Ceratonia siliqua gum ... 

FIGURE 6.6 The differential distribution of the contact strength for the contact between two gypsum dehydrate crystals brought into edge-to-edge contact with a force,/=10 dyn, in solutions of calcium sulfate the various degrees of supersaturation, a, for the contact time t = 100 s (a) the various contact times, t, for supersaturation, a = 1.8 (b). The ordinate depicts the density of the distribution, p. 

If an adhesive contains a large amount of fillers (such as calcium carbonate, calcium sulfate, sand that are dense) its specific gravity will be high, probably higher than 1.2 or 1.3, and consequently the consumption will be higher. Manufacturers TDS should always indicate the density of A and S. 

Fused sodium chloride is electrolyzed at hath temperature varying between 565 to 600°C at a cell voltage of 5.7 to 7 V and the cell current varying from 25 to 35 kA. The cathode current density is mostly about 9.8 kA/m. Often calcium chloride is added to sodium chloride in the cell bath to lower its melting point. Calcium is largely removed from sodium by filtration at about 110°C. Other electrolyte compositions have heen used in which calcium is partially or fully replaced. The cell feed must he free of sulfate and other impurities. 

---