Boron special

Pinanediol (S)-[Chloro(phenyl)methyl]boronate Special Procedure12 ... 

It forms an ion BCI4 only under special circumstances, and never in aqueous solutions (cf. BF3). Like the trifluoride, it is an electron pair acceptor, but the adducts formed tend to decompose more readily. Unlike the corresponding aluminium chloride, boron trichloride exists only as the monomer. 

As special cases lo these ratlii, belter values are used for the elements boron to oxygen (br particular bybrifli/alion stales. 

Elemental boron and the borates are not considered to be toxic, and they do not require special care in handling. However, some of the more exotic boron hydrogen compounds are definitely toxic and do require care. 

Arsenic and Boron. Arsenic and boron form volatile fluorides which are difficult to separate from high purity HF. Special equipment and techniques must be used to remove the arsenic. 

Toluene reacts with carbon monoxide and butene-1 under pressure in the presence of hydrogen fluoride and boron trifluoride to give 4-methyl-j iYbutyrophenone which is reduced to the carbinol and dehydrated to the olefin. The latter is cycHzed and dehydrogenated over a special alumina-supported catalyst to give pure 2,6- dim ethyl n aph th a1 en e, free from isomers. It is also possible to isomerize various dim ethyl n aph th a1 en es to the... 

Boron and carbon form one compound, boron carbide [12069-32-8] B C, although excess boron may dissolve ia boron carbide, and a small amount of boron may dissolve ia graphite (5). Usually excess carbon appears as graphite, except for the special case of boron diffused iato diamonds at high pressures and temperatures, eg, 5 GPa (50 kbar) and 1500°C, where boron may occupy both iaterstitial and substitutional positions ia the diamond lattice, a property utilized ia synthetic diamonds (see Carbon, diamond, synthetic). 

Uses. Hot-pressed hBN is useful for high temperature electric or thermal insulation, vessels, etc, especially in inert or reducing atmospheres, and for special materials such as IITV semiconductors (qv). Its low thermal expansion makes it resistant to thermal shock. The powder can be used as a mold release agent or as thermal insulation. Boron nitride is also available in fiber form (19). BN deposited pyrolyticaHy on refractory substrates at 1200—1800°C has a turbostratic stmcture and low porosity it has greater chemical resistance and is impervious to helium. 

For a large number of applications involving ceramic materials, electrical conduction behavior is dorninant. In certain oxides, borides (see Boron compounds), nitrides (qv), and carbides (qv), metallic or fast ionic conduction may occur, making these materials useful in thick-film pastes, in fuel cell apphcations (see Fuel cells), or as electrodes for use over a wide temperature range. Superconductivity is also found in special ceramic oxides, and these materials are undergoing intensive research. Other classes of ceramic materials may behave as semiconductors (qv). These materials are used in many specialized apphcations including resistance heating elements and in devices such as rectifiers, photocells, varistors, and thermistors. 

Lewis acids are defined as molecules that act as electron-pair acceptors. The proton is an important special case, but many other species can play an important role in the catalysis of organic reactions. The most important in organic reactions are metal cations and covalent compounds of metals. Metal cations that play prominent roles as catalysts include the alkali-metal monocations Li+, Na+, K+, Cs+, and Rb+, divalent ions such as Mg +, Ca +, and Zn, marry of the transition-metal cations, and certain lanthanides. The most commonly employed of the covalent compounds include boron trifluoride, aluminum chloride, titanium tetrachloride, and tin tetrachloride. Various other derivatives of boron, aluminum, and titanium also are employed as Lewis acid catalysts. 

For a specially orthotropic square boron-epoxy plate with stiffness ratios 0 /022= 10 and (Di2-t-2D66) = 1, the four lowest frequencies are displayed in Table 5-3 along with the four lowest frequencies of an isotropic plate. There, the factor k is defined as... 

The second special case is an orthotropic lamina loaded at angle a to the fiber direction. Such a situation is effectively an anisotropic lamina under load. Stress concentration factors for boron-epoxy were obtained by Greszczuk [6-11] in Figure 6-7. There, the circumferential stress around the edge of the circular hole is plotted versus angular position around the hole. The circumferential stress is normalized by a , the applied stress. The results for a = 0° are, of course, identical to those in Figure 6-6. As a approaches 90°, the peak stress concentration factor decreases and shifts location around the hole. However, as shown, the combined stress state at failure, upon application of a failure criterion, always occurs near 0 = 90°. Thus, the analysis of failure due to stress concentrations around holes in a lamina is quite involved. 

The hydrides of the later main-group elements present few problems of classification and are best discussed during the detailed treatment of the individual elements. Many of these hydrides are covalent, molecular species, though association via H bonding sometimes occurs, as already noted (p. 53). Catenation flourishes in Group 14 and the complexities of the boron hydrides merit special attention (p. 151). The hydrides of aluminium, gallium, zinc (and beryllium) tend to be more extensively associated via M-H-M bonds, but their characterization and detailed structural elucidation has proved extremely difficult. 

The importance of the trihalides as industrial chemicals stems partly from their use in preparing crystalline boron (p. 141) but mainly from their ability to catalyse a wide variety of organic reactions.BF3 is the most widely used but BCI3 is employed in special cases. Thus, BF3 is manufactured on the multikilotonne scale whereas the production of BCI3 (USA, 1990) was 250 tonnes and BBr3 was about 23 tonnes. BF3 is shipped in steel cylinders containing 2.7 or 28 kg at a pressure of 10-12 atm, or in tube trailers... 

In order to get the pore system of zeolites available for adsorption and catalysis the template molecules have to be removed. This is generally done by calcination in air at temperatures up to 500 °C. A careful study (ref. 12) of the calcination of as-synthesized TPA-containing MFI-type single crystals by infrared spectroscopy and visible light microscopy showed that quat decomposition sets in around 350 °C. Sometimes special techniques are required, e.g. heating in an ammonia atmosphere (ref. 13) in the case of B-MFI (boron instead of aluminum present) to prevent loss of crystallinity of the zeolite during template quat removal. 

A special kind of oxidative addition occurs between phosphine cobalt hydride complexes and boron halides ... 

A special type of oxidative addition takes place between cobaltocene and boron halides (MeBBr2, PhBCl2, BCI3, BBr3) . Treatment of cobaltocene in hexane or... 

---