Boiling stocks

With higher boiling stocks, mild Hydrofining of kerosene effects desulfurization, color improvement, and a reduction in wick char. Hydrofining improves odor and by reducing sulfur content makes the kerosene less corrosive. 

In this study, a novel Monolith alumina structure was of interest as a base (or a carrier) material for Co-Mo-Alumina catalysts. The specific interest centered around assessing the suitability of the catalyst prepared by impregnating the novel alumina support with Co and Mo for hydrodesulfurization (HDS) and hydrodenitrogenation (HDN) of a relatively high boiling stock. The Monolith catalyst was also tested on a low boiling coal-derived liquid. 

The hydrodesulfurization (HDS) and hydrodenitrogenation (HDN) activities of two Co-Mo-alumina catalysts were tested on two coal derived liquids using a trickle bed reactor system. The two liquids used were Synthoil liquid (high-boiling stock) and Raw Anthracene Oil (low-boiling stock). One of the two catalysts was prepared in the laboratory at Oklahoma State University by... 

Their production in a refinery begins with base stocks having narrow boiling ranges and high octane numbers iso C5 cuts (used in small concentrations because of their high volatility) or alkylates are sought for such formulations. 

Temperature and pressure are not considered as primary operating variables temperature is set sufficiendy high to achieve rapid mass-transfer rates, and pressure is sufficiendy high to avoid vaporization. In Hquid-phase operation, as contrasted to vapor-phase operation, the required bed temperature bears no relation to the boiling range of the feed, an advantage when heat-sensitive stocks are being treated. 

Low temperature filtration (qv) is a common final refining step to remove paraffin wax in order to lower the pour point of the oil (14). As an alternative to traditional filtration aided by a propane or methyl ethyl ketone solvent, catalytic hydrodewaxing cracks the wax molecules which are then removed as lower boiling products. Finished lubricating oils are then made by blending these refined stocks to the desired viscosity, followed by introducing additives needed to provide the required performance. Table 3 Usts properties of typical commercial petroleum oils. Methods for measuring these properties are available from the ASTM (10). 

Rerunning is a second distillation step applied to distUlate stocks in order to remove undesirable higher boiling materials from the product. These materials may be... 

Internal reflux is induced by means of externally cooled liquid pumparounds. A pumparound simply removes hot liquid from the tower, pumps it through a heat exchanger and then introduces this cooled liquid into the tower a few trays above. Use of pumparounds allows a better distribution of tower loadings than if all the heat were removed from the VPS using an overhead condenser. Four to six trays between sidestreams and two pumparounds are normally specified for a lube VPS. The three liquid sidestream products to be used as lube plant feed stocks are steam stripped to remove lighter boiling components which condense with tire sidestreams. 

The cat products become feed to other units, such as alkylation and polymerization plants. High boiling liquid products are used to make lubes, and the gas goes into the refinery fuel systems. Cat cracking feed stocks come from atmospherie and vacuum stills, phenol extraction plants, hydrotreaters, deasphalters and cokers. 

Since cracking stocks generally do not have to meet the color specifications that lube distillates do, higher flash zone temperatures (up to 8(X)°F) can be tolerated. Fuel units are normally designed to distill material boiling up to 1100°F (at atmospheric pressure) from the feed, and some units have distilled beyond 12(X)°F at low feed rates. 

Rerunning is a second distillation step applied to distillate stocks in order to remove undesirable higher boiling materials from the product. These materials may be present because of poor fractionation in the primary distillation step more frequently they are heavy polymers formed in treating operations. Rerunning may be combined with solvent removal, as in the case of heavy lube distillates which are diluted with naphtha to lower their viscosity before being chemically treated. 

A condensible blowdown tank, designed on a similar basis to that described above for phenol, may be provided in other services where a conventional condensible blowdown drum would not be acceptable (e.g., due to effluent water pollution considerations). Examples of such cases are methyl ethyl ketone (MEK) and dimethyl formamide (DMF). A suitable absorbing material is specified (e.g., a lube oil stock for MEK water for DMF), and the design must include consideration of maximum permissible operating temperatures to prevent excessive vapor evolution or the boiling of water. 

---