Boilers power plants

The need to remove NO from stationary sources such as industrial boilers, power plants, waste and biomass incinerators and gasifiers, engines, and gas turbines was emphasized in the 1980s. 

Steam boiler (power plant) Chemical/thermal 85... 

First of all, a technical clarification is necessary in the wider sense, motor fuels are chemical compounds, liquid or gas, which are burned in the presence of air to enable thermal engines to run gasoline, diesel fuel, jet fuels. The term heating fuel is reserved for the production of heat energy in boilers, furnaces, power plants, etc. 

A circulating fluidized-bed boiler, using raw shale oil as a feedstock, is being used to supply process heat for the phosphate operations and to operate a 100-MW power plant. Scale-up in the 1990s should increase the electric power generation to 1000 MW (71). 

Emissions control systems play an important role at most coal-fired power plants. For example, PC-fired plants sited in the United States require some type of sulfur dioxide control system to meet the regulations set forth in the Clean Air Act Amendments of 1990, unless the boiler bums low sulfur coal or benefits from offsets from other highly controlled boilers within a given utiUty system. Flue-gas desulfurization (FGD) is most commonly accomphshed by the appHcation of either dry- or wet-limestone systems. Wet FGD systems, also referred to as wet scmbbers, are the most effective solution for large faciUties. Modem scmbbers can typically produce a saleable waUboard-quaUty gypsum as a by-product of the SO2 control process (see SULFURREMOVAL AND RECOVERY). 

In 1991, Goodyear began working with Cadence Environmental Energy (Indiana) to market a whole tine feed system to supplement fuel for cement kilns. The system is used by several cement manufacturers. In 1992, Goodyear furnished tines for a Tennessee Valley Authority (TVA) test bum at a Memphis power plant. The electric utiUty used tine-derived fuel (TDE) to supplement coal fuel in a cyclone boiler. These tests were successflil. 

As of the mid-1990s, many older conventional steam plants have been converted to combined cycle. The old boiler is removed and replaced by a combustion turbine and heat recovery steam generator. Although the cycle efficiency is not as high as completely new plants, substantial capital cost is avoided by the modification and reuse of existing steam turbine and auxiHary equipment. In many combined cycle power plants, steam is injected into the combustors of the combustion turbine to lower peak flame temperatures and consequendy lower NO. ... 

Constmction of new power plants in the coal region of the western United States presents serious problems in states whose laws dictate zero effluent. In these plants, cooling-tower water withdrawn from rivers cannot be returned to them. In these situations, cooling-tower effluent is purified by distillation (vapor-compression plants have predominated) and by a combination of distillation and membrane technology. The converted water then is used as boiler feedwater the plant blowdown (effluent) is evaporated from open-air lined pools, and pool sediment is periodically buried back in the coal mine with the flue ashes. 

Three demonstrations of the LIMB technology have been carried out. The first was a privately funded project in the 75 MWt Boiler 405 at the No. 4 AC Station of Inland Steel Industries, Inc. (56). By injecting 70 wt % minus 200 mesh (74 -lm) limestone, approximately 40% SO2 removal was achieved at a Ca S ratio of 3. This rose to 50% removal when the Ca S ratio was increased to 4. The second LIMB demonstration was the backup desulfurization system installed by B W as part of the relocation, repowering, and reconfiguration of the PCS power plant (46). 

The combined cycle is also appHcable to dedicated power production. When the steam from the waste heat boiler is fed to a condensing turbine, overall conversion efficiencies of fuel to electricity in excess of 50% can be achieved. A few pubHc utihty power plants use this cycle, but in general utihties have been slow to convert to gas turbines. Most electricity is generated by the cycle shown in Figures 5d and 6d. 

III. Rules for Construc tion of Nuclear Power Plant Components IV Heating Boilers V Nondestructive Examination T. Rules for Care and Operation of Heating Boilers TI. Guidelines for the Care of Power Boilers... 

Process Water Purification Boiler feed water is a major process apphcation of RO. Sealants and colloids are particularly well rejected by membranes, and TDS is reduced to a level that makes ion exchange or continuous deionization for the residual ions very economic. Even the extremely high quahty water required for nuclear power plants can be made from seawater. The iiltra-high quahty water required for production of electronic microcircuits is usually processed starting with two RO systems operating in series, followeci by many other steps. 

These heaters are avaifable with rotors up to 6 m (20 ft) in diameter. Gas temperatures up to 1255 K (1800°F) can be accommodated. Gas face velocity is usually around 2.5 m/s (500 ft/min). The rotor height depends on service, efficiency, and operating conditions but usually is between 0.2 and 0.91 m (8 and 36 in). Rotors are driven by small motors with rotor speed up to 20 r/min. Heater effectiveness can be as high as 85 to 90 percent neat recovery. Lungstrom-type heaters are used in power-plant boilers and also in the process industries for heat recoveiy and for air-conditioning and building heating. 

Thermal power plant auxiliaries such as flow control of primary air fan, ID fan and forced-draught fans, boiler feed pumps circulating water pumps and condensate pumps, coal handling plant (e.g. ball mill, wagon tippler, and stacker reclaimer)... 

The predominant air pollution problem of the nineteenth century was smoke and ash from fhe burning of coal or oil in the boiler furnaces of stationary power plants, locomotives, and marine vessels, and in home heating fireplaces and furnaces. Great Britain took the lead in addressing this problem, and, in the words of Sir Hugh Beaver (3) ... 

Utilities and industrial power plant fuel-fired boilers coal - pulverized coal - cyclone cole - stoker oil wood - bark bagasse fluid coke... 

---