Based on diisocyanates

It was not until the 1930s tliat the work of Caruthers in the U.S. and Bayer in (Icnnany led to the development of polymers based on diisocyanates and triisocyanates. The first polymers were based on diamines the technology quickly shifted toward polyethers and polyesters. Isocyanate development after the 1930s has focused on aromatic isocyanates, more specifically on two molecules and close... 

Formulations for particleboard and plywood adhesives based on combinations of diisocyanates and compounds from renewable resources like tannins, starch, and proteins have been developed and tested at the Fraunhofer-Institute. All in all, the results of gluing tests indicated the potential for using diisocyanates combined with natural polymers for adhesive purposes where each natural product used alone will fail. More attempts will be necessary to find precise mixtures to produce successful adhesives for panel products. The development of adequate particleboard and plywood glue formulations based on diisocyanates and natural polymers has to be accompanied by more sophisticated technologies than those used in conventional production processes. The results presented here may give some hints on how these technologies can evolve. 

Figure 5. Dynamic shear modulus-temperature behavior (torsion pendulum, 1 Hz) of 50% w/w HS copolyurethanes based on diisocyanates FDI-a (F) and MDI (M). Soft segment glass transition and hard-segment melting are in the temperature regions indicated, respectively, by and Tm.

The emulsion polymerisation of vinyl acetate-ethylene copolymers using emulsion stabilisers based on diisocyanate chain extended polyethylene glycol was compared with emulsion polymerisation using conventional stabilisers. The prepared polymers were characterised by determination of glass transition temperatures and by dynamic mechanical investigations. 5 refs. 

Table 7.3. Some Physicomechanical Properties of Semi-SINs Based on Diisocyanates and Polar Monomers Prepared under Optimum Conditions ...

G. P. Belonovskaya, J. D. Chernova, L. A. Korotneva, L. S. Andriarova, L. S. Andriarova, B. A. Dolgoplosk, S. K. Zakharov, Yu. N. Sazanov, K. K. Kalninsh, L. M. Kaljuzhnaya, and M. F. Lebedeva, Interpenetrating Polymer Networks Based on Diisocyanates and Polar Monomers, Eur. Polym. J. 12(11), 817-823 (1976). Rubber, synthetic poly(propylene sulfide)-poly(tolylene diisocyanate) compatible interpenetrating networks. Polyisocyanate network, tensile, strength. 

A series of novel polyurethane (PU) thermoplastic blends based on diisocyanates of variable geometry was recently obtained. On employing the one shot technique, either in solution or in melt and using DBDI as a diisocyanate of variable geometry, by selective dissolution... 

Ak2o has been iastmmental ia developiag a new process for the stereospecific synthesis of 1,4-cyclohexane diisocyanate [7517-76-2] (21). This process, based on the conversion of poly(ethylene terephthalate) [25038-59-9] circumvents the elaborate fractional crystallisation procedures required for the existing -phenylenediamine [108-45-2] approaches. The synthesis starts with poly(ethylene terephthalate) (PET) (32) or phthaUc acid, which is converted to the dimethyl ester and hydrogenated to yield the cyclohexane-based diester (33). Subsequent reaction of the ester with ammonia provides the desired bisamide (34). The synthesis of the amide is the key... 

Interfdci l Composite Membra.nes, A method of making asymmetric membranes involving interfacial polymerization was developed in the 1960s. This technique was used to produce reverse osmosis membranes with dramatically improved salt rejections and water fluxes compared to those prepared by the Loeb-Sourirajan process (28). In the interfacial polymerization method, an aqueous solution of a reactive prepolymer, such as polyamine, is first deposited in the pores of a microporous support membrane, typically a polysulfone ultrafUtration membrane. The amine-loaded support is then immersed in a water-immiscible solvent solution containing a reactant, for example, a diacid chloride in hexane. The amine and acid chloride then react at the interface of the two solutions to form a densely cross-linked, extremely thin membrane layer. This preparation method is shown schematically in Figure 15. The first membrane made was based on polyethylenimine cross-linked with toluene-2,4-diisocyanate (28). The process was later refined at FilmTec Corporation (29,30) and at UOP (31) in the United States, and at Nitto (32) in Japan. 

Polyurethane dispersions (PUD s) are usually high-performance adhesives based on crystalline, hydrophobic polyester polyols, such as hexamethylene adipate, and aliphatic diisocyanates, such as methylene bis(cyclohexyl isocyanate) (H12MDI) or isophorone diisocyanate (IPDI). These PUD s are at the more expensive end of the waterborne adhesive market but provide excellent performance. 

Applications for blocked urethane adhesives are small. However, they may be used as flocking adhesives or as crosslinkers for solvent-borne adhesives. Blocked urethane adhesives are also used as splicing adhesives for belts. Blocked isocyanates based on TDI, IPDI, and derivatives of hexamethylene diisocyanate are most commonly commercially available. 

Adhesives based on isocyanate (especially PMDl, polymethylene diisocyanate, more exactly polymeric 4,4 -diphenylmethane diisocyanate) have been used for more than 25 years in the wood-based panel industry [88], but still have a low market value in the wood-working industry compared to systems based on UF-, MUF- or PF-resins. The main application is the production of waterproof panels, but also the production of panels from raw materials that are difficult to glue, like straw, bagasse, rice shells or sugar cane bagasse. They can be used as adhesives for wood-based products like particleboard, oriented strandboard (OSB), laminated strand lumber (LSL), medium-density fiberboard (MDF) or... 

Polyurethane networks based on triisocyante and diisocyanate connected by segments consisting of polyisobutylene are rubbery and exhibit high temperature properties, hydrolyic stability, and barrier characteristics. ... 

Singer S.M. and Allot M.T., Thermoplastic polyurethane elastomer based on a saturated hydroxyl terminated polyol, difunctional aromatic chain extender and 1,5-naphthalene diisocyanate, US Patent 5 599 874, 1997. 

---