Attribute-group

Indeed, by attributing group 8 to 2-pentanol the following comparative results are obtained ... 

The next step is to weight in a logical and subject-oriented way selected attribute-groups differently. For example One might be more interested in parameters than in chemicals or verse visa. 

Let nl and n2 be the numbers of attributes in two attribute groups (here parameters and chemicals, respectively), wl and w2 the weights by which the attributes of the one group and those of the other group are combined, and m the relative weight. Then, maintaining the normalization to 1 the weights can be calculated as follows in eqn. 4 and 5 ... 

Xu, Z., "Approaches for multiple attribute group decision making based on intuitionistic fuzzy power aggregation operators," Knowledge Based Systems, 24, pp. 749-760, 2011. 

Klein and co-workers have documented the remarkable lubricating attributes of polymer brushes tethered to surfaces by one end only [56], Studying zwitterionic polystyrene-X attached to mica by the zwitterion end group in a surface forces apparatus, they found /i < 0.001 for loads of 100 and speeds of 15-450 nm/sec. They attributed the low friction to strong repulsions existing between such polymer layers. At higher compression, stick-slip motion was observed. In a related study, they compared the friction between polymer brushes in toluene (ji < 0.005) to that of mica in pure toluene /t = 0.7 [57]. 

Still another type of adsorption system is that in which either a proton transfer occurs between the adsorbent site and the adsorbate or a Lewis acid-base type of reaction occurs. An important group of solids having acid sites is that of the various silica-aluminas, widely used as cracking catalysts. The sites center on surface aluminum ions but could be either proton donor (Brpnsted acid) or Lewis acid in type. The type of site can be distinguished by infrared spectroscopy, since an adsorbed base, such as ammonia or pyridine, should be either in the ammonium or pyridinium ion form or in coordinated form. The type of data obtainable is illustrated in Fig. XVIII-20, which shows a portion of the infrared spectrum of pyridine adsorbed on a Mo(IV)-Al203 catalyst. In the presence of some surface water both Lewis and Brpnsted types of adsorbed pyridine are seen, as marked in the figure. Thus the features at 1450 and 1620 cm are attributed to pyridine bound to Lewis acid sites, while those at 1540... 

Besides specifications on atoms, bonds, branches, and ring closure, SLN additionally provides information on attributes of atoms and bonds, such as charge or stereochemistry. These are also indicated in square [ ] or angle < > brackets behind the entity e.g., trans-butane CH3CH=[s=t]CHCH3). Furthermore, macro atoms allow the shorthand specification of groups of atoms such as amino adds, e.g., Ala, Protein2, etc. A detailed description of these specifications and also specifications for 2D substructure queries or combinatorial libraries can be found in the literature [26]. 

Theoretical work by the groups directed by Sustmann and, very recently, Mattay attributes the preference for the formation of endo cycloadduct in solution to the polarity of the solvent Their calculations indicate that in the gas phase the exo transition state has a lower energy than the endo counterpart and it is only upon introduction of the solvent that this situation reverses, due to the difference in polarity of both transition states (Figure 1.2). Mattay" stresses the importance of the dienophile transoid-dsoid conformational equilibrium in determining the endo-exo selectivity. The transoid conformation is favoured in solution and is shown to lead to endo product, whereas the cisoid conformation, that is favoured in the gas phase, produces the exo adduct This view is in conflict with ab initio calculations by Houk, indicating an enhanced secondary orbital interaction in the cisoid endo transition state . 

The influence of alkyl groups has been attributed to the +/ effect operating primarily at the 0- and />-positions (i), and somewhat less strongly at the m-position by relay. Alternatively, the effect is seen as stabilising the transition states for 0- and />-substitution (ii), more than... 

As illustrated in Scheme 8.1, both 2-vinylpyrroles and 3-vinylpyiroles are potential precursors of 4,5,6,7-tetrahydroindolcs via Diels-Alder cyclizations. Vinylpyrroles are relatively reactive dienes. However, they are also rather sensitive compounds and this has tended to restrict their synthetic application. While l-methyl-2-vinylpyrrole gives a good yield of an indole with dimethyl acetylenedicarboxylate, ot-substitiients on the vinyl group result in direct electrophilic attack at C5 of the pyrrole ring. This has been attributed to the stenc restriction on access to the necessary cisoid conformation of the 2-vinyl substituent[l]. 

The principal reactions of this class of compounds are summarized in Scheme 172. In most of these reactions the reactive nucleophilic center is the terminal NHj group, although the other exocyclic nitrogen may also be involved, as shown by acetylation, which yields 284 and 285. However, the structure of compound 281 is not the one proposed in a recent report (1582) that attributes the attack to the other exocyclic nitrogen. The formation of osazones (287) from sugars, 2-hydrazinothiazoles, and hydrazine has been reported (525, 531). 

At first, the dimeric nature of the base isolated from 3-ethyl-2-methyl-4-phenylthiazolium was postulated via a chemical route. Indeed the adduct of ICH, on a similar 2-ethylidene base is a 2-isopropylthiazolium salt in the case of methylene base it is an anilinovinyl compound identified by its absorption spectrum and chemical reactivity (45-47). This dimeric structure of the molecule has been definitively established by its NMR spectrum. It is very similar to the base issued from 2.3-dimethyl-benzo thiazolium (48). It corresponds to 2-(3 -ethyl-4 -phenyl-2 -methylenethiazolinilydene)2-methyl-3-ethyl-4-phenylthiazoline (13). There is only one methyl signal (62 = 2.59), and two series of signals (63= 1.36-3.90, 63= 1.12-3.78) correspond to ethyl groups. Three protons attributed to positions T,5,5 are shifted to a lower field 5.93, 6.58, and 8.36 ppm. The bulk of the ten phenyl protons is at 7.3 ppm (Scheme 22). 

In 1880, Liebermann and Voltzkow (40), and then Voltzkow (41), condensing chloroacetic acid with both ethyl N-phenylthiocarbamate and p-tolylisothiocyanate obtained homologous compounds to which they attributed formulas 40 and 41, whereas their structure probably derives from that of 38 by substituting an aryl group on the cyclic nitrogen. 

Substitution by a methyl group increases AG° and AH°, and this increase is attributed to polar effects. As can be seen from Table III-15, there is an increase in AG and AH° of roughly 1 kcal/mole for each methyl group. Similar effects have been observed with picolines and lutidines (151). There is only a slight difference for the isomeric compounds, the substituent effect being weakest for the 5-derivative. 

As m the 1 4 dimethylcyclohexanes the 6 kJ/mol (1 5 kcal/mol) energy difference between the more stable (trans) and the less stable (cis) stereoisomer is attributed to the strain associated with the presence of an axial methyl group m the cis isomer... 

---