Argon plasma flame

Gases and volatile materials can be swept into the center of an argon plasma flame, where they are fragmented into ions of their constituent elements. The m/z values of ions give important information for identification of the elemental composition of a sample, and precise measurement of ion abundances is used to provide accurate isotope ratios. 

The most commonly used technique of sample introduction is aspiration of the solution into the argon plasma flame. Because of the high temperatures in the flame, many of the problems associated with atomic absorption are eliminated. However, matrix effects such as significant differences in viscosity between sample and standard solutions can still have an effect. When needed, most of the techniques of sample introduction used in atomic absorption spectrophotometry can also be used for sample introduction in emission spectrophotometry [see the review articles " listed in the references]. 

Praseodymium oxide powder of 99.999% purity, obtained from the American Potash Company (Lindsay Division), was reduced to the sesqui-oxide in an evacuated platinum container at 850°C. Pressed pellets of the sesquioxide were sintered in vacuum by rf-induced radiative heating by a tantalum susceptor for 3 hr at 1800°C. The sintered oxide was crushed and dropped through an rf-induced argon plasma flame into a platinum crucible... 

Therefore, if a large quantity of sample is introduced into the flame over a short period of time, the flame temperature will fall, thus interfering with the basic processes leading to the formation and operation of the plasma. Consequently introduction of samples into a plasma flame needs to be controlled, and there is a need for special sample-introduction techniques to deal with different kinds of samples. The major problem with introducing material other than argon into the plasma flame is that the additives can interfere with the process of electron formation, a basic factor in keeping the flame self-sustaining. If electrons are removed from the plasma by... 

Fundamentally, introduction of a gaseous sample is the easiest option for ICP/MS because all of the sample can be passed efficiently along the inlet tube and into the center of the flame. Unfortunately, gases are mainly confined to low-molecular-mass compounds, and many of the samples that need to be examined cannot be vaporized easily. Nevertheless, there are some key analyses that are carried out in this fashion the major one i.s the generation of volatile hydrides. Other methods for volatiles are discussed below. An important method of analysis uses lasers to vaporize nonvolatile samples such as bone or ceramics. With a laser, ablated (vaporized) sample material is swept into the plasma flame before it can condense out again. Similarly, electrically heated filaments or ovens are also used to volatilize solids, the vapor of which is then swept by argon makeup gas into the plasma torch. However, for convenience, the methods of introducing solid samples are discussed fully in Part C (Chapter 17). 

The volatile hydride (arsine in Equation 15.1) is swept by a. stream of argon gas into the inlet of the plasma torch. The plasma flame decomposes the hydride to give elemental ions. For example, arsine gives arsenic ions at m/z 75. The other elements listed in Figure 15.2 also yield volatile hydrides, except for mercury salts which are reduced to the element (Fig), which is volatile. In the plasma flame, the arsine of Equation 15.1 is transformed into As ions. The other elements of Figure 15.2 are converted similarly into their elemental ions. 

Suffice it to say at this stage that the surfaces of most solids subjected to such laser heating will be heated rapidly to very high temperatures and will vaporize as a mix of gas, molten droplets, and small particulate matter. For ICP/MS, it is then only necessary to sweep the ablated aerosol into the plasma flame using a flow of argon gas this is the basis of an ablation cell. It is usual to include a TV monitor and small camera to view the sample and to help direct the laser beam to where it is needed on the surface of the sample. 

Figure 19.7 shows a typical construction of a concentric-tube nebulizer. The sample (analyte) solution is placed in the innermost of two concentric capillary tubes and a flow of argon is forced down the annular space between the two tubes. As it emerges, the fast-flowing gas stream causes a partial vacuum at the end of the inner tube (Figure 19.4), and the sample solution lifts out (Figure 19.5). Where the emerging solution meets the fast-flowing gas, it is broken into an aerosol (Figure 19.7), which is swept along with the gas and eventually reaches the plasma flame. Uptake of sample solution is commonly a few milliliters per minute.

In a concentric-tube nebulizer, the sample solution is drawn through the inner capillary by the vacuum created when the argon gas stream flows over the end (nozzle) at high linear velocity. As the solution is drawn out, the edges of the liquid forming a film over the end of the inner capillary are blown away as a spray of droplets and solvent vapor. This aerosol may pass through spray and desolvation chambers before reaching the plasma flame. 

The aim of breaking up a thin film of liquid into an aerosol by a cross flow of gas has been developed with frits, which are essentially a means of supporting a film of liquid on a porous surface. As the liquid flows onto one surface of the frit (frequently made from glass), argon gas is forced through from the undersurface (Figure 19.16). Where the gas meets the liquid film, the latter is dispersed into an aerosol and is carried as usual toward the plasma flame. There have been several designs of frit nebulizers, but all work in a similar fashion. Mean droplet diameters are approximately 100 nm, and over 90% of the liquid sample can be transported to the flame. 

For a longitudinal disturbance of wavelength 12 pm, the droplets have a mean diameter of about 3-4 pm. These very fine droplets are ideal for ICP/MS and can be swept into the plasma flame by a flow of argon gas. Unlike pneumatic forms of nebulizer in which the relative velocities of the liquid and gas are most important in determining droplet size, the flow of gas in the ultrasonic nebulizer plays no part in the formation of the aerosol and serves merely as the droplet carrier. 

The sample solution is pumped (e.g., from the end of a liquid chromatographic column) through a capillary tube, near the end of which it is heated strongly. Over a short length of tube, some of the solvent is vaporized and expands rapidly. The remaining liquid and the expanding vapor mix and spray out the end of the tube as an aerosol. A flow of argon carries the aerosol into the plasma flame. 

---