Applications working electrode

Another area where controlled-potential coulometry has found application is in nuclear chemistry, in which elements such as uranium and polonium can be determined at trace levels. Eor example, microgram quantities of uranium in a medium of H2SO4 can be determined by reducing U(VI) to U(IV) at a mercury working electrode. 

One important application of amperometry is in the construction of chemical sensors. One of the first amperometric sensors to be developed was for dissolved O2 in blood, which was developed in 1956 by L. C. Clark. The design of the amperometric sensor is shown in Figure 11.38 and is similar to potentiometric membrane electrodes. A gas-permeable membrane is stretched across the end of the sensor and is separated from the working and counter electrodes by a thin solution of KCl. The working electrode is a Pt disk cathode, and an Ag ring anode is the... 

This experiment introduces hydrodynamic voltammetry using a rotating working electrode. Its application for the quantitative analysis of K4Fe(CN)6 is demonstrated. 

Fig. 19.36 Basic circuit for a poiemiostat. (a) Basic circuit for a potentiostat and electrochemical cell, (b) Equivalent circuit, (c) Circuit of a basic potentiostat. A.E. is the auxiliary electrode, R.E. the reference electrode and W.E. the working electrode (6 and c are from Polen-tiostat and its Applications by J. A. von Fraunhofer and C. H. Banks, Butlerworths (1972))...

In the common method of electro-gravimetric analysis, a potential slightly in excess of the decomposition potential of the electrolyte under investigation is applied, and the electrolysis allowed to proceed without further attention, except perhaps occasionally to increase the applied potential to keep the current at approximately the same value. This procedure, termed constant-current electrolysis, is (as explained in Section 12.4) of limited value for the separation of mixtures of metallic ions. The separation of the components of a mixture where the decomposition potentials are not widely separated may be effected by the application of controlled cathode potential electrolysis. An auxiliary standard electrode (which may be a saturated calomel electrode with the tip of the salt bridge very close to the cathode or working electrode) is inserted in the... 

Chronoamperometry is often used for measuring the diffusion coefficient of electroactive species or the surface area of the working electrode. Analytical applications of chronoamperometry (e.g., in-vivo bioanalysis) rely on pulsing of the potential of the working electrode repetitively at fixed tune intervals. Chronoamperometry can also be applied to the study of mechanisms of electrode processes. Particularly attractive for this task are reversal double-step chronoamperometric experiments (where the second step is used to probe the fate of a species generated in the first step). 

The limited anodic potential range of mercury electrodes has precluded their utility for monitoring oxidizable compounds. Accordingly, solid electrodes with extended anodic potential windows have attracted considerable analytical interest. Of the many different solid materials that can be used as working electrodes, the most often used are carbon, platinum, and gold. Silver, nickel, and copper can also be used for specific applications. A monograph by Adams (17) is highly recommended for a detailed description of solid-electrode electrochemistry. 

As already shown in Figure 6.3b the system exhibits remarkable electrophilic promotional behaviour with p values up to 20.64 This is also shown in Fig. 8.60 which depicts a galvanostatic transient. Application of a negative current between the Pt catalyst-working electrode and the Au counter electrode causes a sharp increase in all reaction rates. In the new steady state of the catalyst (achieved within lhr of current application) the catalytic rate increase of C02 and N2 production is about 700%, while lesser enhancement (250-400%) is observed in the rates of CO and N20 production. The appearance of rate maxima immediately after current application can be attributed to the reaction of NO with previously deposited carbon.64... 

The rate of ammonia production was enhanced by more than 1100% in the nitrogen rich regime (Figs 9.33 and 9.34), upon potential application of -IV between the working electrode and the Ag reference electrode. The extent of the NEMCA effect depends strongly on the kinetic regime of the reaction. Very pronounced non-faradaic behavior is observed in the regime 0.33

[Pg.470]

The most commonly used waveform for in vivo voltammetric measurements is square-wave. This involves the application of a potential pulse to the working electrode for a fixed time at fixed intervals. The current is measurai at the end of the potential pulse to minimize capacitive charging current contributions. This waveform is shown in Fig. 15 A. 

The development of hydrodynamic techniques which allow the direct measurement of interfacial fluxes and interfacial concentrations is likely to be a key trend of future work in this area. Suitable detectors for local interfacial or near-interfacial measurements include spectroscopic probes, such as total internal reflection fluorometry [88-90], surface second-harmonic generation [91], probe beam deflection [92], and spatially resolved UV-visible absorption spectroscopy [93]. Additionally, building on the ideas in MEMED, submicrometer or nanometer scale electrodes may prove to be relatively noninvasive probes of interfacial concentrations in other hydrodynamic systems. The construction and application of electrodes of this size is now becoming more widespread and general [94-96]. 

Polarisation titrations are often referred to as amper-ometric or biamperometric titrations. It is necessary that one of the substances involved in the titration reaction be oxidisable or reducible at the working electrode surface. In general, the polarisation titration method is applicable to oxidation-reduction, precipitation and complex-ation titrations. Relatively few applications involving acid/base titration are found. Amperometric titrations can be applied in the determination of analyte solutions as low as ICE5 M to 10-6 M in concentration. 

The working electrodes, 15 mm diameter discs of poly-crystalline platinum fixed in an araldite body were mechanically polished down to 0.05 nm, dipped in diluted HN03, followed by rinsing with an ultrasonic application. 

Potentiostatic current sources, which allow application of a controlled overpotential to the working electrode, are used widely by electrochemists in surface kinetic studies and find increasing use in limiting-current measurements. A decrease in the reactant concentration at the electrode is directly related to the concentration overpotential, rj0 (Eq. 6), which, in principle, can be established directly by means of a potentiostat. However, the controlled overpotential is made up of several contributions, as indicated in Section III,C, and hence, the concentration overpotential is by no means defined when a given overpotential is applied its fraction of the total overpotential varies with the current in a complicated way. Only if the surface overpotential and ohmic potential drop are known to be negligible at the limiting current density can one assume that the reactant concentration at the electrode is controlled by the applied potential according to Eq. (6). 

The first application of the quartz crystal microbalance in electrochemistry came with the work of Bruckenstein and Shay (1985) who proved that the Sauerbrey equation could still be applied to a quartz wafer one side of which was covered with electrolyte. Although they were able to establish that an electrolyte layer several hundred angstroms thick moved essentially with the quartz surface, they also showed that the thickness of this layer remained constant with potential so any change in frequency could be attributed to surface film formation. The authors showed that it was possible to take simultaneous measurements of the in situ frequency change accompanying electrolysis at a working electrode (comprising one of the electrical contacts to the crystal) as a function of the applied potential or current. They coined the acronym EQCM (electrochemical quartz crystal microbalance) for the technique. 

Chong et al. [742] have described a multielement analysis of multicomponent metallic electrode deposits, based on scanning electron microscopy with energy dispersive X-ray fluorescence detection, followed by dissolution and ICP-MS detection. Application of the method is described for determination of trace elements in seawater, including the above elements. These elements are simultaneously electrodeposited onto a niobium-wire working electrode at -1.40 V relative to an Ag/AgCl reference electrode, and subjected to energy dispersive X-ray fluorescence spectroscopy analysis. Internal standardisation... 

For reductive detection, however, and for some special oxidative applications, other materials perform better with respect to point 1, and usually a few experiments with different electrode materials are necessary to determine the optimum choice of working electrode material, see note in section Background Current in Chapter 2. 

Lithography With the STM Electrochemical Techniques. The nonuniform current density distribution generated by an STM tip has also been exploited for electrochemical surface modification schemes. These applications are treated in this paper as distinct from true in situ STM imaging because the electrochemical modification of a substrate does not a priori necessitate subsequent imaging with the STM. To date, all electrochemical modification experiments in which the tip has served as the counter electrode, the STM has been operated in a two-electrode mode, with the substrate surface acting as the working electrode. The tip-sample bias is typically adjusted to drive electrochemical reactions at both the sample surface and the STM tip. Because it has as yet been impossible to maintain feedback control of the z-piezo (tip-substrate distance) in the presence of significant faradaic current (vide infra), all electrochemical STM modification experiments to date have been performed in the absence of such feedback control. 

We have already briefly described a popular application of amperometry in Chapter 13. This was the electrochemical detector used in HPLC methods. In this application, the eluting mobile phase flows across the working electrode embedded in the wall of the detector flow cell. With a constant potential applied to the electrode (one sufficient to cause oxidation or reduction of mixture components), a current is detected when a mixture component elutes. This current translates into the chromatography peak... 

---