Ammonium molybdates carbonates

It is usually preferable to oxidise the compound directly as follows. Intimately mix 0 02-0 05 g. of the eompound with 3 g. of sodium peroxide and 2 g. of anhydrous sodium carbonate in a niekel erucible. Heat the crueible and its eontents with a small flame, gently at first, afterwards more strongly until the eontents are fused, and eontinue heating for a further 10 minutes. Allow to stand, extract the contents of the crucible with water, and filter. Add exeess of eoneentrated nitrie acid to the filtrate and test with ammonium molybdate reagent as above. A yellow preeipitate indicates the presenee of phosphorus. It must be borne in mind that the above treatment 1 eonvert any arsenie present into arsenate. 

AMMO 2.5 EC , cypermetlu-in, 13 Ammonia, 13 Ammonium acetate, 13 Ammonium arsenate, 13 Ammonium benzoate, 13 Ammonium bicarbonate, 13 Ammonium bifluoride, 14 Ammonium bisulfite, 14 Ammonium carbamate, 14 Ammonium carbonate, 14 Ammonium chloride, 14 Ammonium chlorplatmate, 14 Ammonium clu omate, 14 Ammonium citrate, 14 Ammonium diclu omate, 14 Ammonium fluoride, 14 Ammonium fomiate, 15 Ammonium hexafluorosilicate, 15 Ammonium hydroxide, 15 Ammonium metavanadate, 15 Ammonium molybdate, 15 Ammonium nitrate, 15 Ammonium oxalate, 15 Ammonium perfluorooctanoate, 15 Ammonium persulfate, 15 Ammonium phosphate, 15 Ammonium picrate, 16 Ammonium salicylate, 16... 

Ammonium acetate Ammonium adipate Ammonium benzoate Ammonium bicarbonate Ammonium biflluoride Ammonium binoxalate Ammonium bisulfate Ammonium bitartrate Ammonium tetraborate Ammonium bromide Ammonium carbonate Ammonium chloride Ammonium citrate Ammonium diclnomate Ammonium fluoride Ammonium fluorosilicate Ammonium gluconate Ammonium iodide Ammonium molybdate Ammonium nitrate Ammonium oxalate Ammonium perchlorate Ammonium picrate Ammonium polysulfide Ammonium salicylate Ammonium stearate Ammonium sulfate Ammonium sulfide (hydrosulfide) Ammonium tartrate Ammonium tliiocyanate Ammonium thiosulfate... 

The reaction velocity is comparatively slow, but increases with increasing concentration of acid. The addition of three drops of a neutral 20 per cent ammonium molybdate solution renders the reaction almost instantaneous, but as it also accelerates the atmospheric oxidation of the hydriodic acid, the titration is best conducted in an inert atmosphere (nitrogen or carbon dioxide). 

Better results are obtained by transferring 25.0 mL of the diluted hydrogen peroxide solution to a conical flask, and adding 100 mL 1M(1 20) sulphuric acid. Pass a slow stream of carbon dioxide or nitrogen through the flask, add 10 mL of 10 per cent potassium iodide solution, followed by three drops of 3 per cent ammonium molybdate solution. Titrate the liberated iodine immediately with standard 0.1M sodium thiosulphate in the usual way. 

Small, very thin crystals of molybdenite may be made by fusing together ammonium molybdate, sulfur and potassium carbonate.6 We have ex-... 

The reactants are phthalic anhydride, urea and copper(n) chloride, which are heated in a high-boiling aromatic solvent such as 1,2,4-trichlorobenzene, nitrobenzene or m-dinitrobenzene in the presence of a catalyst, usually ammonium molybdate. The solvent also acts as a heat-transfer medium. On heating to 120 °C an exothermic reaction begins and this temperature is maintained for about an hour. The temperature is then raised to 160-180 °C and kept constant for 6-12 hours. During this time ammonia and carbon dioxide are evolved, together with some solvent the reaction is complete when ammonia evolution ceases. The remaining solvent is then removed by either steam or vacuum distillation. The yield is 90-95%. For many years the solvent process was in almost exclusive use. 

Phthalic anhydride and urea, together with copper(I)chloride and ammonium molybdate, are heated to 200°C in trichlorobenzene. The ratios between the components are the same as in the baking process. Carbon dioxide and ammonia are released to yield Copper Phthalocyanine Blue. The reaction is complete after 2 to 3 hours, producing a yield between 85% and more than 95%. 

Data from tests at 250,275,300, and 325 C were used to calculate pseudo-first order rate constants for the formation of H2S. These data are expressed on a standard Arriienius plot (Fig. 2) for which the linear least squares coefficient of determination, r, is 0.98. The apparent activation energy calculated from the slope is 28.5 kcal/mol. This result is in excellent agreement with the recent work of Abotsi, who studied the performance of carbon-supported hydrodesulfurization catalysts (10). Using Ambersorb XE-348 carbon lo ed with sulfided ammonium molybdate (3% Mo loading) prepared by the same procedure reported here, Abotsi hydrotreated a coal-derived recycle solvent The apparent activation energy for... 

Synonym Ammonia Water Amfbnioformaldehyde Ammonium Acetate Ammonium Acid Fluoride Ammonium Amidosulfonate Ammonium Amidosulphate Ammonium Benzoate Ammonium Bicarbonate Ammonium Bichromate Ammonium Bifluoride Ammonium Carbonate Ammonium Chloride Ammonium Citrate Ammonium Citrate, Dibasic Ammonium Decaborate Octahydrate Ammonium Dichromate Ammonium Disulfate-Nickelate (II) Ammonium Ferric Citrate Ammonium Ferric Oxalate Trihydrate Ammonium Ferrous Sulfate Ammonium Fluoride Ammonium Fluosilicate Ammonium Formate Ammonium Gluconate Ammonium Hydrogen Carbonate Ammonium Hydrogen Fluoride Ammonium Hydrogen Sulfide Solution Ammonium Hydroxide Ammonium Hypo Ammonium Hyposulfite Ammonium Iodide Ammonium Iron Sulfate Ammonium Lactate Ammonium Lactate Syrup Ammonium Lauryl Sulfate Ammonium Molybdate Ammonium Muriate Ammonium Nickel Sulfate Ammonium Nitrate Ammonium Nitrate-Urea Solution Ammonium Oleate... 

Phosphates. — To the solution of 20 gm. of sodium carbonate in 50 cc. of nitric acid add 50 cc. of a solution of ammonium molybdate in nitric acid. No yellow precipitate should form in the liquid on standing two to three hours at about 40° C. 

When a quantitative determination of the phosphoric acid and chlorine is required, a fresh quantity of ash is prepared from a weighed amount of the meat sample mixed with an alkali such as milk of lime, sodium carbonate, etc. The phosphoric acid and the chlorine are determined in the nitric acid solution of the ash, the former by the ammonium molybdate method, and the latter either volumetrically or gravimetrically as silver chloride. 

A. Place about 5 mg of sample into a platinum cmcible, mix with 200 mg of anhydrous potassium carbonate, and ignite over a burner at a red heat for about 10 min. Cool, dissolve the melt in 2 mL of freshly distilled water, warming if necessary, and slowly add 2 mL of ammonium molybdate TS. A deep yellow color appears. 

Oxidations.1 Secondary alcohols are oxidized to ketones in moderate to high yield by hydrogen peroxide (30%) in the presence of the ammonium molybdate, potassium carbonate, and tetra-/i-butylammonium chloride in THF at 20°. Epoxidation is suppressed by the presence of potassium carbonate, which also accelerates the reaction. Primary alcohols are not oxidized under these conditions. 

Several procedures for this chemoselective oxidation utilize molybdenum-based catalysts, with either hydrogen peroxide or r-butyl hydroperoxide as the stoichiometric oxidant. These include ammonium molybdate in the presence of a ph e transfer reagent and hydrogen peroxide, which with pH control (potassium carbonate) will selectively oxidize a secondary alcohol in the presence of a primary alcohol without oxidizing alkenes. In addition hindered alcohols are oxidized in preference to less hindered ones (Scheme 18). 

Preparation.—Although the purest molybdenum is obtained from wulfenite, the chief commercial source is molybdenite, which is converted into the trioxide by roasting in air either with or without the addition of sand, and, on dissolving the residue in ammonia, a solution of ammonium molybdate is obtained. This salt, freed from copper by treatment in ammoniacal solution with ammonium sulphide, and from aluminium by the addition of potassium carbonate, on ignition yields molybdenum dioxide alternatively, heating with excess of sulphur yields pure molybdenum disulphide, MoS, which on roasting, or by treatment with nitric acid, is converted into the trioxide MoOj. ... 

The blue oxide is best obtained by allowing powdered molybdenum to remain for a long time at ordinary temperatures in contact with an aqueous suspension of the trioxide, filtering, and then digesting with a further quantity of molybdenum. The solution is evaporated in vacuo. Cold water used for washing the solid should previously be rendered air-free. Another good method of preparation consists in precipitating in the cold, by means of excess of a solution of hydrated molybdenum tetrachloride, a solution of ammonium molybdate in hydrochloric acid the precipitate is w ashed with air-free w ater in an atmosphere of carbon dioxide, and is dried m vacuo. 

---