Adhesion Sensors

PtOEPK (590/760nm) Food grade PS Paper with adhesive Pre-made (Luxcel) Ethylacetate Adhesive sensor stickers30... 

Medical (coatings, adhesives, sensors and probes, prosthetics and biomedical products, and optical fibers)... 

We affixed four adhesive sensors to each participant (see Figure 4). One sensor was placed on the left side of the upper chest to measure HRV, while the other three sensors were used to measure EMG in the upper fibres of the trapezius in the right shoulder, the extensor carpi radialis in the right forearm, and the tibialis anterior in the lower right leg. 

Although insulators other than aluminum oxide have been tried, aluminum is still used almost universally because it is easy to evaporate and forms a limiting oxide layer of high uniformity. To be restricted, therefore, to adsorption of molecules on aluminum oxide might seem like a disadvantage of the technique, but aluminum oxide is very important in many technical fields. Many catalysts are supported on alumina in various forms, as are sensors, and in addition the properties of the oxide film on aluminum metal are of the greatest interest in adhesion and protection. 

Sagvolden et al. [86] also combined the use of colloids with AFM force sensors to study adhesion. In their case, instead of attaching the colloid to the end of the AFM probe and applying a normal force, they approached the free colloids from side on, with the AFM cantilevered at an angle of approximately 30° to the surface normal. Thus, they applied a predominantly lateral force to the colloid particles. The colloids were coated with protein molecules, and their adhesion was studied against three nonbiological surfaces, consisting... 

In contrast to other analytical methods, ion-selective electrodes respond to an ion activity, not concentration, which makes them especially attractive for clinical applications as health disorders are usually correlated to ion activity. While most ISEs are used in vitro, the possibility to perform measurements in vivo and continuously with implanted sensors could arm a physician with a valuable diagnostic tool. In-vivo detection is still a challenge, as sensors must meet two strict requirements first, minimally perturb the in-vivo environment, which could be problematic due to injuries and inflammation often created by an implanted sensor and also due to leaching of sensing materials second, the sensor must not be susceptible to this environment, and effects of protein adsorption, cell adhesion, and extraction of lipophilic species on a sensor response must be diminished [13], Nevertheless, direct electrolyte measurements in situ in rabbit muscles and in a porcine beating heart were successfully performed with microfabricated sensor arrays [18],... 

The first aspect of biocompatibility is a natural immune response. When a foreign object enters the blood stream, it can be attacked by the body s defense system. The first step is protein adsorption on an object surface. It is believed that the amount and type of protein adsorption is one of the most important steps determining whether the object is tolerated or rejected by the body. The next step is cell adhesion, which may cause aggregation and activation of platelets and triggering of the blood coagulation system with resulting thrombus formation. It may not only lead to sensor failure via surface blocking but directly threatens the patient s health. 

Polymer-based pH sensors are not suitable for continuous in-vivo measurements due to the poor biocompatibility of plasticizers used in the polymer membrane. To minimize such a problem, surface treatment or using a reduced amount of plasticizers has been proposed [71]. In order to improve stability and adhesion, polyurethane has been used as an alternative to PVC membranes in the construction of pH sensing membranes [72, 73],... 

Poor adhesion of membrane to metal is the leading cause of failure in solid-state potentiometric sensors [116], For glass membranes, the mismatch of thermal coefficients of expansion between thin glass membrane and metal (mostly Pt) has been attributed to premature failure due to hairline crack formations in the glass layer [60], For polymer-based membranes, water vapor penetration was reported to compromise the membrane-metal interface, therefore affecting the sensor s performance. 

Yoon el al. [112] reported an all-solid-state sensor for blood analysis. The sensor consists of a set of ion-selective membranes for the measurement of H+, K+, Na+, Ca2+, and Cl. The metal electrodes were patterned on a ceramic substrate and covered with a layer of solvent-processible polyurethane (PU) membrane. However, the pH measurement was reported to suffer severe unstable drift due to the permeation of water vapor and carbon dioxide through the membrane to the membrane-electrode interface. For conducting polymer-modified electrodes, the adhesion of conducting polymer to the membrane has been improved by introducing an adhesion layer. For example, polypyrrole (PPy) to membrane adhesion is improved by using an adhesion layer, such as Nafion [60] or a composite of PPy and Nafion [117],... 

For pH sensors used in in-vivo applications, especially those in continuous pH monitor or implantable applications, hemocompatibility is a key area of importance [150], The interaction of plasma proteins with sensor surface will affect sensor functions. Thrombus formation on the device surface due to accelerated coagulation, promoted by protein adsorption, provided platelet adhesion and activation. In addition, variation in the blood flow rate due to vasoconstriction (constriction of a blood vessel) and sensor attachment to vessel walls, known as wall effect , can cause significant errors during blood pH monitoring [50, 126],... 

In practice, some anticoagulation agents such as heparin or antiplatelet agents, e.g. nitric oxide (NO) are delivered to sensor sites in order to reduce the risk of thrombus formation. Nitric oxide (NO), which is a potent inhibitor of platelet adhesion and activation as well as a promoter of wound healing in tissue, has been incorporated in various polymer metrics including PVC (poly(vinyl-chloride)), PDMS (poly-dimethyl-siloxane) and PU (poly-urethanes). Those NO release polymers have been tested in animals as outer protection coatings and have shown promising effects for the analytical response characteristics of the sensor devices [137],... 

---