Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Adhesion Bond properties

The bulk physical properties of the polymers of the 2-cyanoacryhc esters appear in Table 2. AH of these polymers are soluble in /V-methy1pyrro1idinone, /V,/V-dimethy1foTm amide, and nitromethane. The adhesive bonding properties of typical formulated adhesives are Hsted in Table 3. [Pg.177]

Table 3. Adhesive Bond Properties of 2-Cyanoacrylic Esters with Metals and Various Polymeric Materials... Table 3. Adhesive Bond Properties of 2-Cyanoacrylic Esters with Metals and Various Polymeric Materials...
TABLE 3. ADHESIVE BOND PROPERTIES OF 2-CYANOACRYLIC ESTERS WITH METALS AND VARIOUS POLYMERIC MATERIALS... [Pg.19]

Eickner, H. W., Adhesive Bonding Properties of Various Metals as Affected by Chemical and Anodizing Treatments of die Surfaces, Forest Products Laboratory Reports 1842 and 1842-A, February 1955 and August 1960, Forest Products Laboratory, Madison, WI. [Pg.388]

These surface modifications were performed in "pure" micro-wave (2.45 GHz, "single-mode") or in combined microwave/ radio frequency (2.45 GHz/13.56 MHz, "dual-frequency") plasma. Important systematic changes of the surface composition, wettability, and adhesion of thin metal films were observed for different substrate bias values, and for the different gases. The modified surface-chemical structure is correlated with contact angle hysteresis of water drops this helps to identify which surface characteristics are connected with the wettability heterogeneity and with adhesive bonding properties, and how they are influenced by plasma-surface interactions. [Pg.147]

Heller, K., L.J. Jacobs, and J. Qu, Characterisation of adhesive bond properties using Lamb waves. NDT E International, 33 555-563, 2000. [Pg.312]

H. W. Eickner, Adhesive bonding properties of various metals as affected by chemical and anodizing treatments of the surface, Forest Products Lab Report No. 1842A (1955). [Pg.287]

Brinson, H. F., Dickie, R. A., and Debolt, M. A., Measurement of Adhesive Bond Properties Inclnding Damage by Dynamic Thermal Analysis of a Beam Specimen, J. Adhesion, 55 17-30 (1995)... [Pg.608]

The interphase is the volume of material ia which the properties of one substance gradually change iato the properties of another. The iaterphase is useful for describiag the properties of an adhesive bond. The interface contained within the iaterphase, is the plane of contact between the surface of one material and the surface of another. Except ia certain special cases, the iaterface is imaginary. It is useful ia describiag surface eaergetics. [Pg.229]

Emulsion Adhesives. The most widely used emulsion-based adhesive is that based upon poly(vinyl acetate)—poly(vinyl alcohol) copolymers formed by free-radical polymerization in an emulsion system. Poly(vinyl alcohol) is typically formed by hydrolysis of the poly(vinyl acetate). The properties of the emulsion are derived from the polymer employed in the polymerization as weU as from the system used to emulsify the polymer in water. The emulsion is stabilized by a combination of a surfactant plus a coUoid protection system. The protective coUoids are similar to those used paint (qv) to stabilize latex. For poly(vinyl acetate), the protective coUoids are isolated from natural gums and ceUulosic resins (carboxymethylceUulose or hydroxyethjdceUulose). The hydroHzed polymer may also be used. The physical properties of the poly(vinyl acetate) polymer can be modified by changing the co-monomer used in the polymerization. Any material which is free-radically active and participates in an emulsion polymerization can be employed. Plasticizers (qv), tackifiers, viscosity modifiers, solvents (added to coalesce the emulsion particles), fillers, humectants, and other materials are often added to the adhesive to meet specifications for the intended appHcation. Because the presence of foam in the bond line could decrease performance of the adhesion joint, agents that control the amount of air entrapped in an adhesive bond must be added. Biocides are also necessary many of the materials that are used to stabilize poly(vinyl acetate) emulsions are natural products. Poly(vinyl acetate) adhesives known as "white glue" or "carpenter s glue" are available under a number of different trade names. AppHcations are found mosdy in the area of adhesion to paper and wood (see Vinyl polymers). [Pg.235]

Bonding properties of water-based contact adhesives are similar to those of solvent-based systems, but are free of flammabihty ha2ards. However, drying times are longer and the bond is sensitive to moisture. [Pg.304]

The choice of initiator system depends on the polymerization temperature, which is an important factor in determining final product properties. Cold polymers are generally easier to process than hot polymers and in conventional cured mbber parts have superior properties. The hot polymers are more highly branched and have some advantages in solution appHcations such as adhesives, where the branching results in lower solution viscosity and better cohesion in the final adhesive bond. [Pg.520]

The van der Waals and other non-covalent interactions are universally present in any adhesive bond, and the contribution of these forces is quantified in terms of two material properties, namely, the surface and interfacial energies. The surface and interfacial energies are macroscopic intrinsic material properties. The surface energy of a material, y, is the energy required to create a unit area of the surface of a material in a thermodynamically reversible manner. As per the definition of Dupre [14], the surface and interfacial properties determine the intrinsic or thermodynamic work of adhesion, W, of an interface. For two identical surfaces in contact ... [Pg.77]

Although the acrylate adhesives are readily available and studies have shown that they can produce reasonable bonding properties, they have the disadvantages of having high shrinkage, high fluid absorption, and low service temperatures. Acrylate adhesive applications would be limited. The development of EB-curable epoxy adhesives would have applications in the aerospace and automotive industry and potential wider uses. The most immediate application for these resin systems is composite repair of commercial and military aircraft. [Pg.1010]


See other pages where Adhesion Bond properties is mentioned: [Pg.701]    [Pg.111]    [Pg.352]    [Pg.701]    [Pg.498]    [Pg.715]    [Pg.701]    [Pg.111]    [Pg.352]    [Pg.701]    [Pg.498]    [Pg.715]    [Pg.61]    [Pg.3]    [Pg.178]    [Pg.178]    [Pg.229]    [Pg.231]    [Pg.234]    [Pg.234]    [Pg.224]    [Pg.102]    [Pg.488]    [Pg.308]    [Pg.526]    [Pg.183]    [Pg.76]    [Pg.77]    [Pg.143]    [Pg.433]    [Pg.436]    [Pg.438]    [Pg.455]    [Pg.460]    [Pg.576]    [Pg.774]    [Pg.977]   
See also in sourсe #XX -- [ Pg.352 ]




SEARCH



Adhesion properties

Adhesive bond

Adhesive bonding

Adhesive bonding properties, contaminants

Adhesive properties

Bond properties, adhesives, sources

Bond property

Bonding properties

Mechanically bonding adhesives general properties

© 2024 chempedia.info