Abrasive residual

FIGURE 17.8 Slurry abrasive residues. In case the particle adhesion on the oxide wafer is stronger than the cleaning scrubbing force, abrasive particles remain on the wafer surface. 

All mechanical treatments should be followed by the removal of debris and degreasing to remove any abrasion residues. 

Products are granular, free-flowing, and dust-free by nature, since no flow conditioner dust is used as with sulfur-coated fertilizers. They possess excellent abrasion resistance and handling integrity. Since the outer coating is a hard polymer, the products do not leave waxy residues on material handling and apphcation equipment. 

The solubihty characteristics of sodium acyl isethionates allow them to be used in synthetic detergent (syndet) bars. Complex blends of an isethionate and various soaps, free fatty acids, and small amounts of other surfactants reportedly are essentially nonirritant skin cleansers (66). As a rule, the more detersive surfactants, for example alkyl sulfates, a-olefin sulfonates, and alkylaryl sulfonates, are used in limited amounts in skin cleansers. Most skin cleansers are compounded to leave an emollient residue on the skin after rinsing with water. Free fatty acids, alkyl betaines, and some compatible cationic or quaternary compounds have been found to be especially useful. A mildly acidic environment on the skin helps control the growth of resident microbial species. Detergent-based skin cleansers can be formulated with abrasives to remove scaly or hard-to-remove materials from the skin. 

The addition of therapeutic or cosmetic agents to dentifrices has paralleled advances in knowledge about factors affecting the human dentition. Agents added to dentifrices can act directly on the host tooth stmcture or on specific oral accumulations, for example, the principal action of fluoride is on the tooth enamel. The primary action of an abrasive, however, is on an accumulated stained pellicle. Oral accumulations of interest to preventive dentistry are dental pellicles, dental plaque, dental calculus (tartar), microbial populations responsible for oral malodor, and oral debris (food residues, leukocytes, etc). Plaque is most important because of its potential to do harm. 

It is well known that during liquefaction there is always some amount of material which appears as insoluble, residual solids (65,71). These materials are composed of mixtures of coal-related minerals, unreacted (or partially reacted) macerals and a diverse range of solids that are formed during processing. Practical experience obtained in liquefaction pilot plant operations has frequently shown that these materials are not completely eluted out of reaction vessels. Thus, there is a net accumulation of solids within vessels and fluid transfer lines in the form of agglomerated masses and wall deposits. These materials are often referred to as reactor solids. It is important to understand the phenomena involved in reactor solids retention for several reasons. Firstly, they can be detrimental to the successful operation of a plant because extensive accumulation can lead to reduced conversion, enhanced abrasion rates, poor heat transfer and, in severe cases, reactor plugging. Secondly, some retention of minerals, especially pyrrhotites, may be desirable because of their potential catalytic activity. 

Modern pump designs also include a means for flushing the piston with solvent behind the pump seal (not shown in Figure 13.4). The solvent for this is drawn in from a separate reservoir and pumped back into this same reservoir. The purpose is to continuously rinse the piston free of mobile phase residue such that abrasive solute crystals resulting from a mobile phase that has dried out on the piston will not deposit there. These solutes, such as the salts dissolved in the buffered mobile phases used in ion exchange chromatography, may otherwise crystallize on the piston and then damage the piston or the pump seal when the piston moves back and forth. Mobile phases that contain such solutes must be flushed from the system after use so that there is also no crystallization on the front side of the seal. 

Crosslinking improves resistance to heat, stress cracking and abrasion, and also reduces permanent set after loading, residual monomers and/or oligomers and VOCs (volatile organic compounds). Irradiation is a cold sterilization process. 

LEADX was developed and is manufactured by Proactive Environmental Research and Development, Inc. (PERDI). PERDI indicates that patents are pending in the United States for processing and treatment of CRT such as those used for displays in televisions and computer monitors. Patents are also pending in the United States for the use of LEADX as an abrasive additive for sandblasting to immobilize lead from lead paint residue. LEADX is distributed by Proactive Applied Solutions Corporation (PASCO). EnviroBest Corporation markets two paint removers containing LEADX called PR-40/LEADX and PR-40AF/LEADX . 

---