Big Chemical Encyclopedia

Chemical substances, components, reactions, process design ...

Articles Figures Tables About

Wire harness connectors

Well mutually plug the PAB module airbag wiring harness connector clip and safety airbag wiring harness PAB side connector clip it is the end of PAB module installation. [Pg.394]

Check clock spring wiring harness connector clip Place the ignition switch in LOCK position Release accumulator negative wire and wait for 1 minute plus Remove steering pillar shell Release the clock spring connector clip, is it in normal condition Normal Next step... [Pg.402]

In addition to wire harness connectors, printed circuit board-attached connectors, for automotive or electronic applications, also benefit from many of SPS s performance characteristics, including low viscosity, which helps to fill thin walls and heat resistance to maintain dimensional stability through lead-free reflow soldering operations (see Table 15.2). The trend toward miniaturization in automotive electronic control modules has increased the need for compact surface mount connector technology, as opposed to bulkier through-hole and wave-soldered alternatives. [Pg.330]

Both board-attached and wire harness connectors benefit from SPS s excellent thermal diffusivity, defined as the ratio of thermal conductivity to volumetric heat capacity. As a result, cycle time models show that injection-molded parts cool quickly in the mold, helping to minimize cycle time and improve dimensional stability of their complex, molded features such as the terminal snap fit features on harness connectors. Tool designers typically cannot place cooling lines in close proximity to these features and the cooling characteristics of SPS are essential to minimizing the cycle time during manufacturing. [Pg.330]

Dropdown slide rails for circuit breaker withdrawal 16 SF6 circuit breaker chamber 17 Auxiliary wiring harness multi-pin plug and socket 18 Integral skid underbase 19 Voltage transformer 20 Earth terminal 21 Fuses 22 Split clamp connectors 23 Earth fault current transformer 24 Incoming adaptor and half coupler. [Pg.274]

Several stress factors affect an exhaust-gas sensor during its lifetime (Fig. 17.15.12, Tab. 7.15.2). Inside the exhaust pipe at gas velocities up to 80 m/s, high temperature, catalyst poisons, particles, and water are assaulting the sensor. From outside thermal, mechanical, and chemical impacts attack the housing, cable outlet, wire harness, and connector depending on the installation position... [Pg.496]

The resistance between the SRS safety airbag system connector clips connectors not within the designated scope SRS safety airbag system driver s side airbag relative wiring harness shorting or shutoff... [Pg.385]

PIT Trichosporum Arthrobacter, Aspergillus niger, Rhizopus delemar Huang and Byrne (1980), Witt et td. (1995), Nagata et al. (1997), Muller et al. (2001) Carpet fiber, textiles, films, engineering thermoplastics, electronic connectors, wire harnesses Yang et eil. (2002), Chen et eil. (2(X)4), Chuah et al. (2001)... [Pg.8]

As the name suggests, these are combinations of flexible PCBs and rigid PCBs in a single nnit. The flexible portion of the circuit is made first and inclnded in the lamination process of the rigid portion of the assembly. This process eliminates wiring harnesses and the associated connectors. Applications include avionics and portable eqnipment snch as laptop compnters. As a rule, a flex-rigid assembly is more expensive than an eqnivalent combination of PCBs and cables. [Pg.290]

As it has become necessary to design more automotive features into the same or smaller package areas, automotive designers have responded by reducing the size of the wiring used for signal transmissions in harness connectors, which allows an increase in electrical connections per unit area. This... [Pg.329]

Lanyard means a flexible line of rope, wire rope, or strap which generally has a connector at each end for connecting the body belt or body harness to a deceleration device, lifeline, or anchorage. [Pg.537]

In spite of indifferent electrical properties, PA 6.6 is used by British Rail to insulate rails from concrete sleepers, as part of the track circuitry for signalling. It finds wide application in switch components in telephone exchanges, and in connector harnesses in car wiring. A radiator header tank (Figure 7.4) uses PA 6.6, chosen in respect of its high heat distortion temperature, since the component frequently experiences temperatures above 100°C and pressures of 90 kNm . ... [Pg.106]

Snap hooks connect the harness to one end of lanyards or lifelines. Effective January 1, 1998, only double-locking snap hooks can be used. Traditional single locking snap hooks cannot be connected to each other because of the possibility of an employee roll-out. A lanyard is a flexible line of rope, wire rope, or strap that has a connector at each end. Lifelines use a flexible line that connects to an anchorage point in the fall arrest system. [Pg.253]


See other pages where Wire harness connectors is mentioned: [Pg.393]    [Pg.393]    [Pg.330]    [Pg.393]    [Pg.393]    [Pg.330]    [Pg.217]    [Pg.416]    [Pg.385]    [Pg.387]    [Pg.402]    [Pg.404]    [Pg.678]    [Pg.3958]    [Pg.3719]    [Pg.170]    [Pg.49]   
See also in sourсe #XX -- [ Pg.330 ]




SEARCH



Connectors

© 2024 chempedia.info