Weak acids common

All organic and other weak acids commonly encountered in industry are satisfactorily handled by high-silicon irons. 

Values of are small for weak acids and they range very widely (Table 4.1). It is common practice to quote values as the negative logarithm to the base ten, i.e. — logjo K.. since such numbers are less cumbersome and positive when Aj < 1. The symbol for -logio is by convention "p/ fhus -logjo becomes pK,. Table 4.1 shows some typical pAg values. 

These are acids which can be regarded, in respect of their formulae (but not their properties) as hydrates of the hypothetical diiodine heptoxide, liO-j. The acid commonly called periodic acid , I2O7. 5H2O, is written HglO (since the acid is pentabasic) and should strictly be called hexaoxoiodic(VII) acid. It is a weak acid and its salts are hydrolysed in solution. It can be prepared by electrolytic oxidation of iodic(V) acid at low temperatures ... 

The benzyl group has been widely used for the protection of hydroxyl functions in carbohydrate and nucleotide chemistry (C.M. McCloskey, 1957 C.B. Reese, 1965 B.E. Griffin, 1966). A common benzylation procedure involves heating with neat benzyl chloride and strong bases. A milder procedure is the reaction in DMF solution at room temperatiue with the aid of silver oxide (E. Reinefeld, 1971). Benzyl ethers are not affected by hydroxides and are stable towards oxidants (e.g. periodate, lead tetraacetate), LiAIH, amd weak acids. They are, however, readily cleaved in neutral solution at room temperature by palladium-catalyzed bydrogenolysis (S. Tejima, 1963) or by sodium in liquid ammonia or alcohols (E.J. Rcist, 1964). 

Example A common misconception is that the conjugate base of a weak acid is strong This is sometimes but not always true It is true for example for ammo nia which is a very weak acid (pK 36) Its conjugate base amide ion (H2N ) is a much stronger base than HO It is not true however for acetic acid both acetic acid and its conjugate base acetate ion are weak The conjugate base of a weak acid will be strong only when the acid is a weaker acid than water... 

The most common strong base for titrating acidic analytes in aqueous solutions is NaOH. Sodium hydroxide is available both as a solid and as an approximately 50% w/v solution. Solutions of NaOH may be standardized against any of the primary weak acid standards listed in Table 9.7. The standardization of NaOH, however, is complicated by potential contamination from the following reaction between CO2 and OH . 

Ion-exchange resins are categorized by the nature of functional groups attached to a polymeric matrix, by the chemistry of the particular polymer in the matrix, and by the porosity of the polymeric matrix. There are four primary types of functionaHty strong acid, weak acid, strong base, and weak base. Another type consists of less common stmctures in specialty resins such as those which have chelating characteristics. 

A problem common to produced water appHcations is the tendency for oil fouling of the resin. If weak acid or chelate resins are used, a two-step regeneration process is required which uses acid to remove calcium and magnesium from the resin, foUowed by a dilute NaOH solution to convert the resin to the sodium form. 

The concentration of acid impurities is an important indication of the quality of petroleum products and the purity of organic solvents, plasticizers, mineral oils, food fats, and polymers. Methods are used to detect organic acids in such compounds have many disadvantages the alkalimetry - low sensitivity, especially in the determination of weak acids, the extraction-photometric method is laborious, instmmental methods are expensive. In addition, most of methods are commonly unsuitable for direct analysis. 

Ion-exchange resins swell in water to an extent which depends on the amount of crosslinking in the polymer, so that columns should be prepared from the wet material by adding it as a suspension in water to a tube already partially filled with water. (This also avoids trapping air bubbles.) The exchange capacity of a resin is commonly expressed as mg equiv./mL of wet resin. This quantity is pH-dependent for weak-acid or weak-base resins but is constant at about 0.6-2 for most strong-acid or strong-base types. 

The most common method of purification of inorganic species is by recrystallisation, usually from water. However, especially with salts of weak acids or of cations other than the alkaline and alkaline earth metals, care must be taken to minimise the effect of hydrolysis. This can be achieved, for example, by recrystallising acetates in the presence of dilute acetic acid. Nevertheless, there are many inorganic chemicals that are too insoluble or are hydrolysed by water so that no general purification method can be given. It is convenient that many inorganic substances have large temperature coefficients for their solubility in water, but in other cases recrystallisation is still possible by partial solvent evaporation. 

Chemical Reactivity - Reactivity with Water Dissolves with a moderate reaction Reactivity with Common Materials None Stability During Transport May become unstable and subject to explosion if stored for extended periods of time or is exposed to high temperatures and pressures Neutralizing Agerus for Acids and Caustics The weak acidity can be neutralized by slaked lime, however this does not destroy the hazardous properties of the material Polymerization Not pertinent Inhibitor of Polymerization Not pertinent. 

Chemical Reactivity - Reactivity with Water. When potassiiun cyanide dissolves in water, a mild reaction occurs and poisonous hydrogen cyanide gas is released. The gas readily dissipates, however if it collects in a confined space, then workers may be exposed to toxic levels. If the water is acidic, toxic amounts of the gas will form instantly Reactivity with Common Materials Contact with even weak acids will result in the formation of deadly hydrogen cyanide gas Stability During Transport Stable Neutralizing Agents for Acids and Caustics Not pertinent Polymerization Not pertinent Inhibitor of Polymerization Not pertinent. 

The proportion of ionized and unionized forms of a chemical compound can be readily calculated according to the above equation. It can be easily seen that pK is also a pH value at which 50% of the compound exists in ionized form. The ionization of weak acids increases as the pH increases, whereas the ionization of weak bases increases when the pH decreases. As the proportion of an ionized chemical increases, the diffusion of the chemical through the biological membranes is greatly impaired, and this attenuates toxicokinetic processes. For example, the common drug acetosalicylic acid (aspirin), a weak acid, is readily absorbed from the stomach because most of its dose is in an unionized form at the acidic pH of the stomach. 

Where do hydrocarbons lie on the acidity scale As the data in Table 8.1 show, both methane (pKa 60) and ethylene (plC, = 44) are very weak acids and thus do not react with any of the common bases. Acetylene, however, has piCa = 25 and can be deprotonated by the conjugate base of any acid whose pKa is greater than 25. Amide ion (NH2-), for example, the conjugate base of ammonia (pKa - 35), is often used to aeprotonate terminal aikynes. 

Manx- different reducing agents are effective, but the most common choice in the laboratory is sodium cyanoborohydride, NaBH3CN. Sodium cyanoboro-hydride is similar in reactivity to sodium borohydride (NaBH4) but is more stable in weak acid solution. 

The 20 common amino acids can be further classified as neutral, acidic, or basic, depending on the structure of their side chains. Fifteen of the twenty have neutral side chains, two (aspartic acid and glutamic acid) have an extra carboxylic acid function in their side chains, and three (lysine, arginine, and histidine) have basic amino groups in their side chains. Note that both cysteine (a thiol) and tyrosine (a phenol), although usually classified as neutral amino acids, nevertheless have weakly acidic side chains that can be deprotonated in strongly basic solution. 

As we have pointed out, strong acids and bases are completely ionized in water. As a result, compounds such as HC1 and NaOH are strong electrolytes like NaCl. In contrast, molecular weak acids and weak bases are poor conductors because their water solutions contain relatively few ions. Hydrofluoric acid and ammonia are commonly described as weak electrolytes. 

This is a quadratic equation in [H + ] and may be solved in the usual manner. It can, however, be simplified by introducing the following further approximations. In a mixture of a weak acid and its salt, the dissociation of the acid is repressed by the common ion effect, and [H + ] may be taken as negligibly small by... 

Discussion. The hydroxides of sodium, potassium, and barium are generally employed for the preparation of solutions of standard alkalis they are water-soluble strong bases. Solutions made from aqueous ammonia are undesirable, because they tend to lose ammonia, especially if the concentration exceeds 0.5M moreover, it is a weak base, and difficulties arise in titrations with weak acids (compare Section 10.15). Sodium hydroxide is most commonly used because of its cheapness. None of these solid hydroxides can be obtained pure, so that a standard solution cannot be prepared by dissolving a known weight in a definite volume of water. Both sodium hydroxide and potassium hydroxide are extremely hygroscopic a certain amount of alkali carbonate and water are always present. Exact results cannot be obtained in the presence of carbonate with some indicators, and it is therefore necessary to discuss methods for the preparation of carbonate-free alkali solutions. For many purposes sodium hydroxide (which contains 1-2 per cent of sodium carbonate) is sufficiently pure. 

A pre-boiler treatment process such as dealkalization (DA) to reduce the alkalinity content of a naturally high alkaline water source may also be suitable. There are various methods of dealkalizing MU water A common process is by weak acid, hydrogen-cycle cation... 

The major problem of these diazotizations is oxidation of the initial aminophenols by nitrous acid to the corresponding quinones. Easily oxidized amines, in particular aminonaphthols, are therefore commonly diazotized in a weakly acidic medium (pH 3, so-called neutral diazotization) or in the presence of zinc or copper salts. This process, which is due to Sandmeyer, is important in the manufacture of diazo components for metal complex dyes, in particular those derived from l-amino-2-naphthol-4-sulfonic acid. Kozlov and Volodarskii (1969) measured the rates of diazotization of l-amino-2-naphthol-4-sulfonic acid in the presence of one equivalent of 13 different sulfates, chlorides, and nitrates of di- and trivalent metal ions (Cu2+, Sn2+, Zn2+, Mg2+, Fe2 +, Fe3+, Al3+, etc.). The rates are first-order with respect to the added salts. The highest rate is that in the presence of Cu2+. The anions also have a catalytic effect (CuCl2 > Cu(N03)2 > CuS04). The mechanistic basis of this metal ion catalysis is not yet clear. 

The parent acids of common polyprotic acids other than sulfuric are weak and the acidity constants of successive deprotonation steps are normally widely different. As a result, except for sulfuric acid, we can treat a polyprotic acid or the salt of any anion derived from it as the only significant species in solution. This approximation leads to a major simplification to calculate the pH of a polyprotic acid, we just use Kal and take only the first deprotonation into account that is, we treat the acid as a monoprotic weak acid (see Toolbox 10.1). Subsequent deprotonations do take place, but provided Kal is less than about fCal/1000, they do not affect the pH significantly and can be ignored. 

Sodium hydrogen carbonate, NaHC03 (sodium bicarbonate), is commonly called bicarbonate of soda or baking soda. The rising action of baking soda in batter depends on the reaction of a weak acid, HA, with the hydrogen carbonate ions ... 

---