Vinyl acetate mechanism

Sivalingam, G., Karthik, R., Madras, G. Blends of poly(e-caprolactone) and poly(vinyl acetate) mechanical properties and thermal degradation. Polym. Degrad. Stab. 84(2), 345-351 (2004)... 

When the solubility is higher, as in the case of vinyl acetate, mechanism B will prevail. In this situation, oligomer radicals may be "desorbed" from the polymer particles and grow further in the water phase. TTiey may be absorbed again or they may form new particles. Because there is a "two-way" traffic, the polymerization rate is not directly related with the number of particles. Polymerization takes place in both phases, though eventually most of the polymer is present as a separate phase. 

The time-temperature superpositioning principle was applied f to the maximum in dielectric loss factors measured on poly(vinyl acetate). Data collected at different temperatures were shifted to match at Tg = 28 C. The shift factors for the frequency (in hertz) at the maximum were found to obey the WLF equation in the following form log co + 6.9 = [ 19.6(T -28)]/[42 (T - 28)]. Estimate the fractional free volume at Tg and a. for the free volume from these data. Recalling from Chap. 3 that the loss factor for the mechanical properties occurs at cor = 1, estimate the relaxation time for poly(vinyl acetate) at 40 and 28.5 C. 

Poly(vinyl acetate). The dielectric and mechanical spectra of hybrids produced by mixing a poly(vinyl acetate)—THE solution with TEOS, followed by the addition of HCl have been investigated (45). Mixtures were made which were beheved to be 0, 5, 10, 15, and 20 wt % Si02, respectively. These composites were transparent and Eourier transform infrared spectroscopy (ftir) revealed hydrogen bonding between the siUcate network and carbonyl units of the poly(vinyl acetate) (PVAc). No shift in the T of the composites from that of the pure PVAc was observed. Similarly, the activation... 

Poly(methyl methacrylate) and poly(vinyl acetate) precipitate from the resin solution as it cures. This mechanism offsets the contraction in volume as the polyester resin cross-links, resulting in a nonshrinking thermoset. Other polymer additives such as poly(butylene adipate) provide similar shrinkage... 

The thermal glass-transition temperatures of poly(vinyl acetal)s can be determined by dynamic mechanical analysis, differential scanning calorimetry, and nmr techniques (31). The thermal glass-transition temperature of poly(vinyl acetal) resins prepared from aliphatic aldehydes can be estimated from empirical relationships such as equation 1 where OH and OAc are the weight percent of vinyl alcohol and vinyl acetate units and C is the number of carbons in the chain derived from the aldehyde. The symbols with subscripts are the corresponding values for a standard (s) resin with known parameters (32). The formula accurately predicts that resin T increases as vinyl alcohol content increases, and decreases as vinyl acetate content and aldehyde carbon chain length increases. 

Many different combinations of surfactant and protective coUoid are used in emulsion polymerizations of vinyl acetate as stabilizers. The properties of the emulsion and the polymeric film depend to a large extent on the identity and quantity of the stabilizers. The choice of stabilizer affects the mean and distribution of particle size which affects the rheology and film formation. The stabilizer system also impacts the stabiUty of the emulsion to mechanical shear, temperature change, and compounding. Characteristics of the coalesced resin affected by the stabilizer include tack, smoothness, opacity, water resistance, and film strength (41,42). 

Mechanisms. Because of its considerable industrial importance as well as its intrinsic interest, emulsion polymerization of vinyl acetate in the presence of surfactants has been extensively studied (75—77). The Smith-Ewart theory, which describes emulsion polymerization of monomers such as styrene, does not apply to vinyl acetate. Reasons for this are the substantial water solubiUty of vinyl acetate monomer, and the different reactivities of the vinyl acetate and styrene radicals the chain transfer to monomer is much higher for vinyl acetate. The kinetics of the polymerization of vinyl acetate has been studied and mechanisms have been proposed (78—82). 

Emulsion Polymerization. Poly(vinyl acetate) and poly(vinyl acetate) copolymer latexes prepared in the presence of PVA find wide appHcations in adhesives, paints, textile finishes, and coatings. The emulsions show exceUent stabiHty to mechanical shear as weU as to the addition of electrolytes, and possess exceUent machining characteristics. 

Vinyl acetate may be easily polymerised in bulk, solution, emulsion and suspension. At conversions above 30%, ehain transfer to polymer or monomer may occur. In the case of both polymer and monomer transfer two mechanisms are possible, one at the tertiary carbon, the other (illustrated in Figure 14.4) at the acetate group. 

These adhesives differ from normal hot-melt adhesives, such as the standard ethylene vinyl acetate hot melts. Standard hot-melt adhesives like EVA have no curing mechanism. They are heated above the crystalline melting point and applied as a low-viscosity liquid in the same manner as is the curing hot melt. The bond is closed in the same manner and strength is developed upon crystallization. 

Coran and Patel [33] selected a series of TPEs based on different rubbers and thermoplastics. Three types of rubbers EPDM, ethylene vinyl acetate (EVA), and nitrile (NBR) were selected and the plastics include PP, PS, styrene acrylonitrile (SAN), and PA. It was shown that the ultimate mechanical properties such as stress at break, elongation, and the elastic recovery of these dynamically cured blends increased with the similarity of the rubber and plastic in respect to the critical surface tension for wetting and with the crystallinity of the plastic phase. Critical chain length of the rubber molecule, crystallinity of the hard phase (plastic), and the surface energy are a few of the parameters used in the analysis. Better results are obtained with a crystalline plastic material when the entanglement molecular length of the... 

For composites with polymerization-modified filler it is typical that the physico-mechanical characteristics should increase symbatically with the quantity of polymer which becomes attached to the filler in the polymerization process. This effect has been observed for polyethylene [293, 321], poly(vinyl chloride) coats [316], and in [336, 337] for kaolin coated with poly(vinyl acetate) and introduced into the copolymer of ethylene and vinyl acetate. 

In a very recent development, Debuigne et at. of vinyl acetate at 30 °C mediated by Co"(acac)2 (121). They obtained predictable molecular weights up to Mn 100000 and dispersities < 1.3 and proposed a polymerization mechanism analogous to that shown in Scheme 9.27. The complex... 

Cooper(I) carboxylates give esters with primary (including neopentyl without rearrangement), secondary, and tertiary alkyl, allylic, and vinylic halides. A simple Sn mechanism is obviously precluded in this case. Vinylic halides can be converted to vinylic acetates by treatment with sodium acetate if palladium(II) chloride is present. ... 

Chemical pretreatments with amines, silanes, or addition of dispersants improve physical disaggregation of CNTs and help in better dispersion of the same in rubber matrices. Natural rubber (NR), ethylene-propylene-diene-methylene rubber, butyl rubber, EVA, etc. have been used as the rubber matrices so far. The resultant nanocomposites exhibit superiority in mechanical, thermal, flame retardancy, and processibility. George et al. [26] studied the effect of functionalized and unfunctionalized MWNT on various properties of high vinyl acetate (50 wt%) containing EVA-MWNT composites. Figure 4.5 displays the TEM image of functionalized nanombe-reinforced EVA nanocomposite. 

Chattopadhyay S., Chaki T.K., and Bhowmick A.K., New thermoplastic elastomers from poly(ethyle-neoctene) (engage), poly(ethylene-vinyl acetate) and low-density polyethylene by electron beam technology structural characterization and mechanical properties. Rubber Chem. TechnoL, 74, 815, 2001. Roy Choudhury N. and Dutta N.K., Thermoplastic elastomeric natural rubber-polypropylene blends with reference to interaction between the components. Advances in Polymer Blends and Alloys Technology, Vol. 5 (K. Finlayson, ed.), Technomic Publishers, Pensylvania, 1994, 161. 

Release of tetracycUne hydrochloride from PCL fibers was evaluated as a means of controlled administration to periodontal pockets (69). Only small amounts of the drug were released rapidly in vitro or in vivo, and poly(ethylene-co-vinyl acetate) gave superior results. Because Fickian diffusion of an ionic hydrochloride salt in a UpophiUc polymer is unlikely, and because PCL and EVA have essentially identical Fickian permeabilities, we attribute this result to leaching of the charged salt by a mechanism similar to release of proteins from EVA (73). Poly-e-caprolactone pellets have been found unsuitable for the release of methylene blue, another ionic species (74,75). In this case, blending PCL with polyvinyl alcohol (75% hydrolyzed) increased the release rate. 

Moiseev et al., who proposed initially that ethylidene diacetate was produced from addition of acetic acid to vinyl acetate, later showed this to be impossible from the result of reaction in CH3CO2D, preferring the following mechanism ... 

Under certain conditions a combination of Pd(II) and Cu(II) in acetic acid oxidises olefins to saturated products which neither reagent produces alone. Although Cu(II) continues to catalyse the production of vinyl acetate through step (46) by a redox mechanism, the following new reaction can be effected... 

The hydrodynamic volume separation mechanism of SEC, along with the different molecular size/weight relationships of branched and linear polymers of identical chemical composition, can be exploited with the SEC/LALLS method to gain information about polymer branching. In the studies described in this paper both conventional SEC and SEC/LALLS are used to obtain data about branching in samples of poly(vinyl acetate) (PVA) and polychloro-prene (PCP). 

---