Vacuum stress

The utilisation of laser holographic interferometry, vacuum stressing and the analysing of the interference fringes of double-exposure of tyres to evaluate tyre structural uniformity, define the type of the defects and to estimate their size is described. Photographs of reconstructed holographic interference patterns of tested tyres are given. 8 refs. 

Pyles R (2003) Aging aircraft USAF workload and material consumption life cycle patterns. RAND, Pittsburgh Rao MV, Samuel R, Ramesh K (1990) Dual vacuum stressing technique for holographic NDT of honeycomb sandwich panels. NDT Int 23 267-270 Reynolds WN (1988) Inspection of laminates and adhesive bonds by pulse-video thermography. NDT Int 21 229-232... 

The importance of low pressures has already been stressed as a criterion for surface science studies. However, it is also a limitation because real-world phenomena do not occur in a controlled vacuum. Instead, they occur at atmospheric pressures or higher, often at elevated temperatures, and in conditions of humidity or even contamination. Hence, a major tlmist in surface science has been to modify existmg techniques and equipment to pemiit detailed surface analysis under conditions that are less than ideal. The scamiing tunnelling microscope (STM) is a recent addition to the surface science arsenal and has the capability of providing atomic-scale infomiation at ambient pressures and elevated temperatures. Incredible insight into the nature of surface reactions has been achieved by means of the STM and other in situ teclmiques. 

Applications The common Heliflow apphcations are tank-vent condensers, sample coolers, pump-seal coolers, and steam-jet vacuum condensers. Instant water heaters, glycoLwater seivdces, and cryogenic vaporizers use the spiral tube s ability to reduce thermally induced stresses caused in these apphcations. 

This, then, is our final design equation. It shows how the survival probability depends on both the stress (rand the volume V of the component. In using it, the first step is to fix on an acceptable failure probability, Pp 0.3 for chalk, 10 for the cutting tool, 10 for the vacuum-chamber window. The survival probability is then given by P = 1 -. ... 

Consider the design of a glass window for a vacuum chamber (Fig. 18.6). It is a circular glass disc of radius R and thickness f, freely supported in a rubber seal around its periphery and subjected to a uniform pressure difference Ap = 0.1 MPa (1 atmosphere). The pressure bends the disc. We shall simply quote the result of the stress analysis of such a disc it is that the peak tensile stress is on the low-pressure face of... 

Silver-copper-palladium alloys with liquidus temperatures of 800-1 000°C have very low vapour pressures combined with good wetting and flow characteristics and are widely employed in vacuum work. They exhibit a lower tendency to stress corrosion than silver-copper, and do not form brittle alloys with other metals. 

The role of the stress in embrittlement and stress-corrosion processes has been examined in some detail by employing the slow strain-rate technique . Specimens of alloy 7179-T651 tested in air or in vacuum after pre-exposure to water at 70° C or in water at various potentials at ambient temperature exhibited a reversible embrittlement in excess of that arising from testing in moist air . The embrittlement was attributed to hydrogen absorption, and recovery was thought to be due to loss of hydrogen (particularly under vacuum) or to diffusion to traps. Potentiostatic tests revealed... 

Sheet forming processes, such as vacuum forming, do have effects on the product. The designer should be aware that these will affect the performance of one s product and one should learn how to modify the design to minimize any deleterious effects. Probably the most serious problem encountered in formed film or sheet products results from the fact that the materials are made from film or sheet at temperatures well below the melt softening point of the plastic, usually near the heat distortion temperature for the material. Forming under these condition when the draw down ratio is exceeded for a specific plastic can result in over stretched orientation of the material, the production of frozen-in stresses, poor product reproducibil-... 

The other effect of having a stretched area is a reduction in resistance to stress cracking. Crazing is a possibility in such areas such as in polystyrenes, and environmental stress cracking caused by solvent substances will occur in the stretched areas. This is a particularly important consideration in vacuum formed products used for packaging food that frequently has some solvent action on the plastics. 

Pyridinecarboxaldehyde (nicotinaldehyde) was supplied by Aldrich-Europe, Beerse, Belgium. The checkers purified this reagent by fractional distillation, b.p. 95-97° (15 mm.). The submitters stress that 3-pyridinecarboxaldehyde should be completely free from contamination by the acid. They stirred 150 g. of the aldehyde with 100 g. of potassium carbonate and 300 ml. of ethanol for 12 hours, filtered the suspended solid, and fractionally distilled the filtrate through a 30-cm. Vigreux column using a water aspirator. However, the checkers found that the recovery of aldehyde from this procedure was very low, and recommend vacuum distillation instead. 3-Pyridinecarboxaldehyde is a powerful skin irritant and should be handled with protective gloves. 

It should be stressed that environment conditions strongly influence the friction behavior of NFC coatings. In Erdemir s work, super-low friction coefficient was attained only in vacuum or an inert gas environment [22,51]. When oxygen and moisture are presented, friction coefficient dramatically increased [22,52,53]. 

---