Vacancy point defects surface vacancies

A block model of defects on a single-crystal surface is depicted in Figure 2.4.17 The surface itself in reality is a two-dimensional defect of the bulk material. In addition, one-dimensional defects in the form of steps which have zero-dimensional defects in the form of kink sites. Terraces, which are also shown in the figure, have a variety of surface sites and may also exhibit vacancies, adatoms, and point defects. Surface boundaries may be formed as a result of surface reconstruction of several equivalent orientations on terraces. 

Let us refer to Figure 5-7 and start with a homogeneous sample of a transition-metal oxide, the state of which is defined by T,P, and the oxygen partial pressure p0. At time t = 0, one (or more) of these intensive state variables is changed instantaneously. We assume that the subsequent equilibration process is controlled by the transport of point defects (cation vacancies and compensating electron holes) and not by chemical reactions at the surface. Thus, the new equilibrium state corresponding to the changed variables is immediately established at the surface, where it remains constant in time. We therefore have to solve a fixed boundary diffusion problem. 

Fig. 8.16. Model of the (110) surface of rutile showing two kinds of anion vacancy point defects (after Henrich, 1983 reproduced with the publisher s permission).

Fig 4 Model of the corundum (1012) surface, including a [0221 ] step to another (1012) terrace, and an 0-vacancy point defect... 

Fig. 5. Model of the rutile (110) surface. Two types of O-vacancy point defect are shown.

An obvious example of the strong effect that chemisorbed molecules can have on surface properties can be seen in Figs. 6 and 7 above for O-vacancy point defects on Ti02. In Fig. 7, the band of electron emission just below Ep originates from electrons trapped in d-orbitals on Ti cations adjacent to the defect. When the reduced surface is exposed to O2 at room temperature, the defect bandgap emission band almost completely vanishes the photoemission spectra look very similar to those from the stoichiometric surface in Fig. 6. In this simple case, it is believed that O2 dissociates at O-vacancy defect sites, removing electrons from the adjacent cations in order to become 0 ions. 

The threshold behavior seen in Fig. 8 suggests that CO does not react readily with the nearly defect-free stoichiometric surface, but that some O ions must be removed, forming 0-vacancy point defects, before a significant reaction can... 

The long and narrow microfibrils are bundled into fibrils their ends, located mainly on the outer surface of fibrils, act as point defects (point vacancies) of the microfibrillar lattice... 

Dislocation theory as a portion of the subject of solid-state physics is somewhat beyond the scope of this book, but it is desirable to examine the subject briefly in terms of its implications in surface chemistry. Perhaps the most elementary type of defect is that of an extra or interstitial atom—Frenkel defect [110]—or a missing atom or vacancy—Schottky defect [111]. Such point defects play an important role in the treatment of diffusion and electrical conductivities in solids and the solubility of a salt in the host lattice of another or different valence type [112]. Point defects have a thermodynamic basis for their existence in terms of the energy and entropy of their formation, the situation is similar to the formation of isolated holes and erratic atoms on a surface. Dislocations, on the other hand, may be viewed as an organized concentration of point defects they are lattice defects and play an important role in the mechanism of the plastic deformation of solids. Lattice defects or dislocations are not thermodynamic in the sense of the point defects their formation is intimately connected with the mechanism of nucleation and crystal growth (see Section IX-4), and they constitute an important source of surface imperfection. 

Materials that contain defects and impurities can exhibit some of the most scientifically interesting and economically important phenomena known. The nature of disorder in solids is a vast subject and so our discussion will necessarily be limited. The smallest degree of disorder that can be introduced into a perfect crystal is a point defect. Three common types of point defect are vacancies, interstitials and substitutionals. Vacancies form when an atom is missing from its expected lattice site. A common example is the Schottky defect, which is typically formed when one cation and one anion are removed from fhe bulk and placed on the surface. Schottky defects are common in the alkali halides. Interstitials are due to the presence of an atom in a location that is usually unoccupied. A... 

Fig. 9. Schematic of a two-dimensional cross section of an AgBr emulsion grain showing the surface and formation of various point defects A, processes forming negative kink sites and interstitial silver ions B, positive kink site and C, process forming a silver ion vacancy at a lattice position and positive kink...

An effect which is frequently encountered in oxide catalysts is that of promoters on the activity. An example of this is the small addition of lidrium oxide, Li20 which promotes, or increases, the catalytic activity of dre alkaline earth oxide BaO. Although little is known about the exact role of lithium on the surface structure of BaO, it would seem plausible that this effect is due to the introduction of more oxygen vacancies on the surface. This effect is well known in the chemistry of solid oxides. For example, the addition of lithium oxide to nickel oxide, in which a solid solution is formed, causes an increase in the concentration of dre major point defect which is the Ni + ion. Since the valency of dre cation in dre alkaline earth oxides can only take the value two the incorporation of lithium oxide in solid solution can only lead to oxygen vacaircy formation. Schematic equations for the two processes are... 

Thermodynamic considerations imply that all crystals must contain a certain number of defects at nonzero temperatures (0 K). Defects are important because they are much more abundant at surfaces than in bulk, and in oxides they are usually responsible for many of the catalytic and chemical properties.15 Bulk defects may be classified either as point defects or as extended defects such as line defects and planar defects. Examples of point defects in crystals are Frenkel (vacancy plus interstitial of the same type) and Schottky (balancing pairs of vacancies) types of defects. On oxide surfaces, the point defects can be cation or anion vacancies or adatoms. Measurements of the electronic structure of a variety of oxide surfaces have shown that the predominant type of defect formed when samples are heated are oxygen vacancies.16 Hence, most of the surface models of... 

The notion of point defects in an otherwise perfect crystal dates from the classical papers by Frenkel88 and by Schottky and Wagner.75 86 The perfect lattice is thermodynamically unstable with respect to a lattice in which a certain number of atoms are removed from normal lattice sites to the surface (vacancy disorder) or in which a certain number of atoms are transferred from the surface to interstitial positions inside the crystal (interstitial disorder). These forms of disorder can occur in many elemental solids and compounds. The formation of equal numbers of vacant lattice sites in both M and X sublattices of a compound M0Xft is called Schottky disorder. In compounds in which M and X occupy different sublattices in the perfect crystal there is also the possibility of antistructure disorder in which small numbers of M and X atoms are interchanged. These three sorts of disorder can be combined to give three hybrid types of disorder in crystalline compounds. The most important of these is Frenkel disorder, in which equal numbers of vacancies and interstitials of the same kind of atom are formed in a compound. The possibility of Schottky-antistructure disorder (in which a vacancy is formed by... 

---