Traps glass

Direct Measurement Trapped Glass Beads Trapped Sand Grains... 

Thermal cycler or other means of heating tubes to 91 C and incubating at 37 C Aspirator with fine tip and liquid trap Glass slides... 

Trapped gas in closed pores often limits densification when sintering witlr a liquid or viscous (glass) phase because rapid material transport tlirough tlie liquid often results in pore closure early in tlie sintering process. 

Method A. In a 500 ml. round-bottomed flask, fitted with a reflux condenser attached to a gas trap (Fig. II, 13, 8), place 59 g. of succinic acid and 117-5 g. (107-5 ml.) of redistilled acetyl chloride. Reflux the mixture gently upon a water bath until all the acid dissolves (1-2 hours). Allow the solution to cool undisturbed and finally cool in ice. Collect the succinic anhydride, which separates in beautiful crystals, on a Buchner or sintered glass funnel, wash it with two 40 ml. portions of anhydrous ether, and dry in a vacuum desiccator. The yield of succinic anhydride, m.p. 118-119°, is 47 g. 

Method 3. Fit up the apparatus shown in Fig. 7F, 45, 1 using a 250-ml, roimd-bottomed flask. Do not pass water through the glass jacket since the condenser wUl be employed only as an air condenser the empty filter flask is used merely as a trap to prevent the escape of vapours into... 

Dihydroxyacetophenone. Finely powder a mixture of 40 g. of dry hydroquinone diacetate (1) and 87 g. of anhydrous aluminium chloride in a glass mortar and introduce it into a 500 ml. round-bottomed flask, fitted with an air condenser protected by a calcium chloride tube and connected to a gas absorption trap (Fig. II, 8, 1). Immerse the flask in an oil bath and heat slowly so that the temperature reaches 110-120° at the end of about 30 minutes the evolution of hydrogen chloride then hegins. Raise the temperature slowly to 160-165° and maintain this temperature for 3 hours. Remove the flask from the oil bath and allow to cool. Add 280 g. of crushed ice followed by 20 ml. of concentrated hydrochloric acid in order to decompose the excess of aluminium chloride. Filter the resulting solid with suction and wash it with two 80 ml. portions of cold water. Recrystallise the crude product from 200 ml. of 95 per cent, ethanol. The 3 ield of pure 2 5-dihydroxyacetophenone, m.p. 202-203°, is 23 g. 

Photomultipliers are used to measure the intensity of the scattered light. The output is compared to that of a second photocell located in the light trap which measures the intensity of the incident beam. In this way the ratio [J q is measured directly with built-in compensation for any variations in the source. When filters are used for measuring depolarization, their effect on the sensitivity of the photomultiplier and its output must also be considered. Instrument calibration can be accomplished using well-characterized polymer solutions, dispersions of colloidal silica, or opalescent glass as standards. 

Rhenium hexafluoride [10049-17-9J, ReF, is a pale yeUow soHd at 0°C, but a Hquid at ambient temperature. In the presence of moisture it hydroly2es rapidly forming HF, Re02, and HRe04 (see Rheniumand rhenium compounds). It is not safe to store ReF in a glass trap or glass-lined container. Leaks in the system can initiate hydrolysis and produce HF. The pressure buildup causes the system to burst and an explosion may result. 

Fig. 4. The glass and vinyl "sandwich" is fed through a special de-aic machine to remove trapped air and increase the adhesion of the vinyl to the glass.

A solution of sodium cyanide [143-33-9] (ca 25%) in water is heated to 65—70°C in a stainless steel reaction vessel. An aqueous solution of sodium chloroacetate [3926-62-3] is then added slowly with stirring. The temperature must not exceed 90°C. Stirring is maintained at this temperature for one hour. Particular care must be taken to ensure that the hydrogen cyanide, which is formed continuously in small amounts, is trapped and neutrali2ed. The solution of sodium cyanoacetate [1071 -36-9] is concentrated by evaporation under vacuum and then transferred to a glass-lined reaction vessel for hydrolysis of the cyano group and esterification. The alcohol and mineral acid (weight ratio 1 2 to 1 3) are introduced in such a manner that the temperature does not rise above 60—80°C. For each mole of ester, ca 1.2 moles of alcohol are added. 

Trihalomethanes. Wherever chlorine is used as a disinfectant in drinking-water treatment, trihalomethanes (THMs) generaUy are present in the finished water. The THMs usuaUy formed are trichloromethane (chloroform), bromodichloromethane, dibromochloromethane, and tribromomethane (bromoform). There are four main techniques for the analysis of THMs headspace, Hquid— Hquid extraction (Ue), adsorption—elution (purge—trap), and direct aqueous injection. The final step in each technique involves separation by gas—Hquid chromatography with a 2 mm ID coUed glass column containing 10 wt % squalene on chromosorb-W-AW (149—177 p.m (80—100 mesh)) with detection generaUy by electron capture. 

---