Transmission electron microscopy diffraction techniques

The present work is part of a research program aimed at a systematic investigation of the parameters controlling the preparation of CoFe/yAlaOs catalysts. Three catalyst series were prepared using different support particle sizes, metal loadings and Co/Co+Fe atomic ratio compositions. The catalysts were characterized by BET surface area, X-ray diffraction and X-ray photoelectrons spectroscopy (XPS) techniques. The samples were tested in the catalytic reaction decomposition of ethylene at 700°C. The MW-CNT quality was determined by thermo-gravimetric (TG) and transmission electron microscopy (TEM) techniques. 

Transmission electron microscopy (TEM) can resolve features down to about 1 nm and allows the use of electron diffraction to characterize the structure. Since electrons must pass through the sample however, the technique is limited to thin films. One cryoelectron microscopic study of fatty-acid Langmuir films on vitrified water [13] showed faceted crystals. The application of TEM to Langmuir-Blodgett films is discussed in Chapter XV. 

Transmission electron microscopy (tern) is used to analyze the stmcture of crystals, such as distinguishing between amorphous siUcon dioxide and crystalline quartz. The technique is based on the phenomenon that crystalline materials are ordered arrays that scatter waves coherently. A crystalline material diffracts a beam in such a way that discrete spots can be detected on a photographic plate, whereas an amorphous substrate produces diffuse rings. Tern is also used in an imaging mode to produce images of substrate grain stmctures. Tern requires samples that are very thin (10—50 nm) sections, and is a destmctive as well as time-consuming method of analysis. 

A progressive etching technique (39,40), combined with x-ray diffraction analysis, revealed the presence of a number of a polytypes within a single crystal of sihcon carbide. Work using lattice imaging techniques via transmission electron microscopy has shown that a-siUcon carbide formed by transformation from the P-phase (cubic) can consist of a number of the a polytypes in a syntactic array (41). 

In this paper, the bulk material was obtained by impregnation of the silica host with GFP solution and nanosised by sonication, preserving the features of both the biomolecule and the mesoporous structure. An exhaustive physical chemical characterisation of the nanosized materials was performed by structural (X-Ray Diffraction, Transmission Electron Microscopy), volumetric and optical (photoluminescence spectroscopy) techniques. 

Microporous nanoparticles with ordered zeolitic structure such as Ti-Beta are used for incorporation into walls or deposition into pores of mesoporous materials to form the micro/mesoporous composite materials [1-3], Microporous particles need to be small enough to be successfully incorporated in the composite structure. This means that the zeolite synthesis has to be stopped as soon as the particles exhibit ordered zeolitic structure. To study the growth of Ti-Beta particles we used 29Si solid-state and liquid-state NMR spectroscopy combined with x-ray powder diffraction (XRPD) and high-resolution transmission electron microscopy (HRTEM). With these techniques we monitored zeolite formation from the initial precursor gel to the final Ti-Beta product. 

Ffirai and Toshima have published several reports on the synthesis of transition-metal nanoparticles by alcoholic reduction of metal salts in the presence of a polymer such as polyvinylalcohol (PVA) or polyvinylpyrrolidone (PVP). This simple and reproducible process can be applied for the preparation of monometallic [32, 33] or bimetallic [34—39] nanoparticles. In this series of articles, the nanoparticles are characterized by different techniques such as transmission electronic microscopy (TEM), UV-visible spectroscopy, electron diffraction (EDX), powder X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) or extended X-ray absorption fine structure (EXAFS, bimetallic systems). The great majority of the particles have a uniform size between 1 and 3 nm. These nanomaterials are efficient catalysts for olefin or diene hydrogenation under mild conditions (30°C, Ph2 = 1 bar)- In the case of bimetallic catalysts, the catalytic activity was seen to depend on their metal composition, and this may also have an influence on the selectivity of the partial hydrogenation of dienes. 

The main techniques employed for the characterization of clusters include UV/vis optical absorption, luminescence, mass spectrometry, X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), and Fourier transform infrared (FT-IR). Single crystal X-ray diffraction (XRD) has been used to determine the structures of a few clusters [17-19]. 

Figure 1.4 Comparison of the application ranges of techniques that are sensitive to nearsurface strains. Minimum detection limits are plotted against depth resolution of the measurement. XRD X-ray diffraction DOR differential optical reflectometry. RBS Rutherford back scattering MEIS medium energy ion scattering TEM transmission electron microscopy...

A mineral is a naturally occurring, crystalline inorganic compound with a specific chemical composition and crystal structure. Minerals are commonly named to honor a person, to indicate the geographic area where the mineral was discovered, or to highlight some distinctive chemical, crystallographic, or physical characteristic of the substance. Each mineral sample has some obvious properties color, shape, texture, and perhaps odor or taste. However, to determine the precise composition and crystal structure necessary to accurately identify the species, one or several of the following techniques must be employed optical, x-ray diffraction, transmission electron microscopy and diffraction, and chemical and spectral analyses. 

The size and morphology are characteristic parameters of metal particles. It is possible to determine them by various techniques transmission electron microscopy (TEM) [105-107], X-ray photoelectron spectroscopy (XPS) [108], X-ray diffraction (XRD), extended X-ray absorption fine structure (EXAES) [109, 110], thermoprogrammed oxidation, reduction or desorption (TPO, TPR or TPO) and chemisorption of probe molecules (H2, O2, CO, NO) are currently used. It is therefore possible to know the particles (i) size (by TEM) [105-107], extended X-ray absorption fine structure (EXAES) [109, 110]), (ii) structure (by XRD, TEM), (iii) chemical composition (by TEM-EDAX, elemental analysis), (iv) chemical state (surface and bulk metal atoms by XPS [108], TPD, TPR, TPO) and... 

TECHNIQUES OF HIGH RESOLUTION TRANSMISSION ELECTRON MICROSCOPY (HREM), TRANSMISSION EM (TEM) DIFFRACTION CONTRAST, AND ANALYTICAL EM (AEM)... 

---