Titanium precipitation

Titanium oxide (Ti02). This is produced from dmenite ore by mixing ore with carbon and heating in a rotary kiln. Also, the rotary lain is used in the process of recovery of titanium oxide from hydrated titanium precipitate at about 1250 K. 

If the normal carbonate is used, the basic carbonate or white lead, Pb(OH),. 2PbCO,. is precipitated. The basic carbonate was used extensively as a base in paints but is now less common, having been largely replaced by either titanium dioxide or zinc oxide. Paints made with white lead are not only poisonous but blacken in urban atmospheres due to the formation of lead sulphide and it is hardly surprising that their use is declining. 

AISI 321 and 347 are stainless steels that contain titanium and niobium iu order to stabilize the carbides (qv). These metals prevent iatergranular precipitation of carbides during service above 480°C, which can otherwise render the stainless steels susceptible to iatergranular corrosion. Grades such as AISI 316 and 317 contain 2—4% of molybdenum, which iacreases their creep—mpture strength appreciably. In the AISI 200 series, chromium—manganese austenitic stainless steels the nickel content is reduced iu comparison to the AISI 300 series. 

Preparation and Manufacture. Magnesium chloride can be produced in large quantities from (/) camalhte or the end brines of the potash industry (see Potassium compounds) (2) magnesium hydroxide precipitated from seawater (7) by chlorination of magnesium oxide from various sources in the presence of carbon or carbonaceous materials and (4) as a by-product in the manufacture of titanium (see Titaniumand titanium alloys). 

Aluminum. All primary aluminum as of 1995 is produced by molten salt electrolysis, which requires a feed of high purity alumina to the reduction cell. The Bayer process is a chemical purification of the bauxite ore by selective leaching of aluminum according to equation 35. Other oxide constituents of the ore, namely siUca, iron oxide, and titanium oxide remain in the residue, known as red mud. No solution purification is required and pure aluminum hydroxide is obtained by precipitation after reversing reaction 35 through a change in temperature or hydroxide concentration the precipitate is calcined to yield pure alumina. 

Metals can be precipitated from the Hquid or gas phase. For example, nickel ammonium carbonate gives nickel powder when subjected to hydrogen in an autoclave. Copper, cobalt, molybdenum, and titanium powders can also be formed by precipitation. 

Nickel—Copper. In the soHd state, nickel and copper form a continuous soHd solution. The nickel-rich, nickel—copper alloys are characterized by a good compromise of strength and ductihty and are resistant to corrosion and stress corrosion ia many environments, ia particular water and seawater, nonoxidizing acids, neutral and alkaline salts, and alkaUes. These alloys are weldable and are characterized by elevated and high temperature mechanical properties for certain appHcations. The copper content ia these alloys also easure improved thermal coaductivity for heat exchange. MONEL alloy 400 is a typical nickel-rich, nickel—copper alloy ia which the nickel content is ca 66 wt %. MONEL alloy K-500 is essentially alloy 400 with small additions of aluminum and titanium. Aging of alloy K-500 results in very fine y -precipitates and increased strength (see also Copper alloys). 

In addition to these principal alloying elements, which provide soHd solution strengthening and/or precipitation strengthening, wrought alloys may contain small amounts of titanium and boron [7440-42-8J, B, for control of ingot grain size, and ancillary additions of chromium, manganese, and zirconium to provide dispersoids. AH commercial alloys also contain iron and siUcon. 

Hydrated Titanium Oxides. Hydroxides of Ti(Il) (black) and Ti(Ill) (brown) are precipitated when an alkaU metal hydroxide is added to a solution of the corresponding salt. These precipitates, though difficult to purify (45), are powerful reduciag agents and readily oxidize ia air to form a hydrated titanium dioxide. 

Hydrolysis of solutions of Ti(IV) salts leads to precipitation of a hydrated titanium dioxide. The composition and properties of this product depend critically on the precipitation conditions, including the reactant concentration, temperature, pH, and choice of the salt (46—49). At room temperature, a voluminous and gelatinous precipitate forms. This has been referred to as orthotitanic acid [20338-08-3] and has been represented by the nominal formula Ti02 2H20 (Ti(OH). The gelatinous precipitate either redissolves or peptizes to a colloidal suspension ia dilute hydrochloric or nitric acids. If the suspension is boiled, or if precipitation is from hot solutions, a less-hydrated oxide forms. This has been referred to as metatitanic acid [12026-28-7] nominal formula Ti02 H2O (TiO(OH)2). The latter precipitate is more difficult to dissolve ia acid and is only soluble ia concentrated sulfuric acid or hydrofluoric acid. 

Precipitation of a hydrated titanium oxide by mixing aqueous solutions of titanium chloride with alkaU forms the precipitation seeds, which are used to initiate precipitation in the Mecklenburg (50) variant of the sulfate process for the production of pigmentary titanium dioxide. Hydrolysis of aqueous solutions of titanium chloride is also used for the preparation of high purity (>99.999%) titanium dioxide for electroceramic appHcations (see Ceramics). In addition, hydrated titanium dioxide is used as a pure starting material for the manufacture of other titanium compounds. 

The reactivity of titanium dioxide toward acid is dependent on the temperature to which it has been heated. Freshly precipitated titanium dioxide is soluble iu concentrated hydrochloric acid. However, titanium dioxide that has been heated to 900°C is almost iusoluble iu acids except hot concentrated sulfuric, iu which the solubiUty may be further iucreased by the addition of ammonium sulfate to raise the boiling poiut of the acid, and hydrofluoric acid. Similarly, titanium dioxide that has been calciued at 900°C is almost iusoluble iu aqueous alkahes but dissolves iu molten sodium or potassium hydroxide, carbouates, or borates. 

---