Thermoset matrices epoxy

Epoxy, bisphenol / /epichlorohydrin resin, thermosetting matrix Epoxy, bisphenol / /epichlorohydrin resin, toners... 

For thermoset-matrix materials, heat is usually added as a catalyst to speed the natural chemical reaction of polymerization. Two-part epoxies, such as found in your local hardware store, consist of a tube of epoxy and a tube of chemical hardener that react when mixed. Heat... 

Thermosensitive hydrogels, 13 743 THERMOSET Thermoset recycling pyramid, 13 780-781 Thermoset elastomers, 20 71 Thermoset epoxy resins, curing of, 10 421 Thermoset flexible polyurethane foams properties of, 25 461 Thermoset matrix composites, 21 456 Thermo set molding properties of diallyl isophthalate, 2 262t Thermoset polymers, 25 455 cured, 10 425... 

Epoxy resins are thermosetting matrix resins, characterized by the epoxide group [48,193], as shown in Figure 2.9. 

DMTA is a very interesting tool for characterizing heterogeneous materials in which domains of distinct Tg values coexist. The most interesting cases involve modified thermosets of different types (see Chapter 8). Examples are the use of rubbers (e.g., liquid polybutadiene and random copolymers), or thermoplastics (e.g., polyethersulphone or polyetherimide in epoxy matrices or poly(vinyl acetate) in unsaturated polyesters), as impact modifier (epoxies), or low-profile additives (polyesters). The modifier-rich phase may be characterized by the presence of a new a peak (Fig. 11.10). But on occasions there may be superposition of peaks and the presence of the modifier cannot be easily detected by these techniques. If part of the added polymer is soluble in the thermoset matrix, its eventual plasticizing effect can be determined from the corresponding matrix Tg depletion, and the... 

Several basic morphologies are observed in thermoplastic-modified epoxies and, indeed, other thermosets. Homogeneous [Fig. 6(A), in which no phase separation is observed] and particulate [Fig. 6(B), in which the modifier phase separates to produce small domains] morphologies occur at low concentrations of modifier. In these cases, the thermoplastic modifier is encapsulated within a thermoset matrix, whereas in the phase-inverted morphology, [Fig. 6(C)] the minor thermoplastic component is the continuous phase surrounding large, discontinuous domains of the major... 

Polymer composites are plastics within which fibres are embedded. The plastic is known as the matrix (resin) and the fibres dispersed witbin it are known as the reinforcement Thermosetting matrix materials include polyester, vinyl ester and epoxy resins. For higher temperature and extreme environments, bismaleimlde, polyimide and phenolic resins are used. Composites can be used to replace metal parts but care must be taken during design. Most engineering materials have similar properties in any direction (called isotropic) where composites have not This can however be offset by arranging the reinforcement layers in varying directions. 

Polymer-based composites can be divided into thermoset and thermoplastic composites, which due to their different properties show diverse fracture mechanism. Due to tight three-dimensional molecular network structure of the most of thermoset matrixes such as epoxy resins, they exhibit inherent brittle fracture behavior and poor... 

Several theories have been proposed to explain the toughening effect of rubber particles on the brittle thermoset matrix. These are based on the fractographic features and fracture properties of rubber-toughened thermoset networks. Garg and Mai [113] proposed 13 mechanisms to explain the impact behaviour of rubber-toughened epoxy... 

The APC materials typically nsed for on-site rehabilitation of timber and concrete are composed of glass, carbon or aramid fibres and a polyester, epoxy or polynrethane polymeric matrix. Glass fibres are the most frequently used due to their moderate cost and good mechanical properties when compared to carbon fibres. They are used normally in the form of pultruded profiles or strips, fabrics (tissues) or mats. Carbon fibres are mainly used in the form of pultruded profiles of solid, open or hollow cross-sectional shapes. While in timber applications both thermoplastic and thermosetting matrix types are used, in concrete applications only the latter type is used. 

One of the most important methods for controlling the yield behaviour of polymers is rubber modification, which is widely used to increase fracture resistance. The technique was first used in 1948 to modify the properties of polystyrene, and has since been extended to most of the major plastics, including polypropylene, polycarbonate, and rigid PVC, and to a number of the less highly crosslinked thermosets, notably epoxy resins. Between S and 20 % of a suitable rubber is added in the form of small particles, which are typically between 0.1 and S /im in diameter. Chemically reactive rubbers are preferred, because they form bonds with molecules of the surrounding matrix which can withstand tensile stress. The rubber particles have low moduli, and therefore act as stress concentrators. Accelerated deformation in the matrix adjacent to the rubber particles results in a lowering of the yield stress. 

Matrix Materials Polymers used for matrix materials are usually thermosets, with epoxies being the most common (35). Others are polyesters and phenolics. Sometimes thermoplastics are used, principally polyimides, polysulfones, and polyetheretherketone (PEEK). The matrix has several roles in polymer-fiber composites. These include maintaining desired fiber spacing, transmitting shear loads between layers of fiber, and reducing the tendency to transmit stress concentration from broken fibers to intact fibers. 

---