The Vinyls

The group designated as vinyl polymers usually excludes vinyl benzene (styrene), vinyl cyanide (acrylonitrile), and vinyl fluoride (Appendix 16.F). The observation recorded by Regnault in 1838, that vinylidene chloride is converted by exposure to sunlight in a sealed glass tube to an insoluble polymer, often is cited as the beginning 

---

Figure 10.4 The oxychlorination step of the vinyl chloride process. (From Smith and Petela, Chem. Eng., 513 24, 1991 reproduced by permission of the Institution of Chemical Engineers.)...

A fiowsheet for this part of the vinyl chloride process is shown in Fig. 10.5. The reactants, ethylene and chlorine, dissolve in circulating liquid dichloroethane and react in solution to form more dichloroethane. Temperature is maintained between 45 and 65°C, and a small amount of ferric chloride is present to catalyze the reaction. The reaction generates considerable heat. 

Figure 10.5 The direct chlorination step of the vinyl chloride process using a liquid phase reactor. (From McNaughton, Chem. Engg., December 12, 1983, pp. 54-58 reproduced by permission.)...

Soret band of the macrocycle, a ti to tt transition, is excited instead. It has been found that the vinyl groups do not participate in the conjugated system [4]. This is based on the fact that the vinyl C=C stretch does not... 

Figure Bl.22.10. Carbon K-edge near-edge x-ray absorption (NEXAFS) speetra as a fiinotion of photon ineidenee angle from a submonolayer of vinyl moieties adsorbed on Ni(lOO) (prepared by dosing 0.2 1 of ethylene on that surfaee at 180 K). Several eleetronie transitions are identified in these speetra, to both the pi (284 and 286 eV) and the sigma (>292 eV) imoeeupied levels of the moleeule. The relative variations in the intensities of those peaks with ineidenee angle ean be easily eonverted into adsorption geometry data the vinyl plane was found in this ease to be at a tilt angle of about 65° from the surfaee [71], Similar geometrieal detenninations using NEXAFS have been earried out for a number of simple adsorbate systems over the past few deeades.

Stabilizing the resulting enolate of the Michael Addition product can shift the equilibrium as in the case of the vinyl silane shown below... 

Synthesis The vinyl anion synthon can either be the vinyl Grignard reagent or the acetylide arrion, in which case the synthesis becomes ... 

The vinyl anion synthon is best represented by an acetylide ion (frame 33). Synthesis ... 

C/760 mmHg) sulfur dichloride After the addition stirring v/as stopped and the flask was allowed to stand for 15 h in the ice-bath. The condenser was replaced with a drying tube containing CaCl (refluxing of the vinyl chloride had stopped completely after the addition of sulfur dichloride). 

A more eflicient and general synthetic procedure is the Masamune reaction of aldehydes with boron enolates of chiral a-silyloxy ketones. A double asymmetric induction generates two new chiral centres with enantioselectivities > 99%. It is again explained by a chair-like six-centre transition state. The repulsive interactions of the bulky cyclohexyl group with the vinylic hydrogen and the boron ligands dictate the approach of the enolate to the aldehyde (S. Masamune, 1981 A). The fi-hydroxy-x-methyl ketones obtained are pure threo products (threo = threose- or threonine-like Fischer formula also termed syn" = planar zig-zag chain with substituents on one side), and the reaction has successfully been applied to macrolide syntheses (S. Masamune, 1981 B). Optically pure threo (= syn") 8-hydroxy-a-methyl carboxylic acids are obtained by desilylation and periodate oxidation (S. Masamune, 1981 A). Chiral 0-((S)-trans-2,5-dimethyl-l-borolanyl) ketene thioketals giving pure erythro (= anti ) diastereomers have also been developed by S. Masamune (1986). 

Dibromopropene was used in an efficient thermodynamically controlled alkylation. Hydrolysis of the vinyl bromide yielded a 1,4-diketone (S.C. Welch, 1979). 

Extensive studies on the Wacker process have been carried out in industrial laboratories. Also, many papers on mechanistic and kinetic studies have been published[17-22]. Several interesting observations have been made in the oxidation of ethylene. Most important, it has been established that no incorporation of deuterium takes place by the reaction carried out in D2O, indicating that the hydride shift takes place and vinyl alcohol is not an intermediate[l,17]. The reaction is explained by oxypailadation of ethylene, / -elimination to give the vinyl alcohol 6, which complexes to H-PdCl, reinsertion of the coordinated vinyl alcohol with opposite regiochemistry to give 7, and aldehyde formation by the elimination of Pd—H. 

The stereo-defined enol ester 432 is prepared by the reaction of the vinyl-mercurial 431, obtained by acetoxymercuration of 2-butyne. with mercury(II) carboxylates using a catalytic amount of Pd(OAc)2[392]. 

Alkenylation of cyclopentenone with the alkenylstannane 719 has been used for the introduction of an a,>-chain into a prostaglandin derivative[590]. Even the vinyl mesylate (methanesulfonate) 720 can be used for coupling with alkenylstannanes[59l]. 

No intennolecular reaction of malonate or /3-keto esters with halides has been reported, but the intramolecular reaction of /3-diketones such as 790 and malonates proceeds smoothly[652,653]. Even the simple ketone 791 can be arylated or alkenylated intramolecularly. In this reaction, slow addition of a base is important to prevent alkyne formation from the vinyl iodide by elim-ination[654]. 

The cis thioboration of terminal alkynes with 9-(arylthio)-9-BBN is catalyzed by Pd(Pli3P)4 in the presence of styrene. The product 136 is converted into the vinyl sulfides 137 and 138 by the treatment with MeOH or by Pd-catalyzed cross-coupling with aryl or alkenyl halides using K3PO4 in DMF[68]. No thioboration takes place with internal alkynes. 

Hydrometallation is catalyzed by Pd. Hydroboration of l-buten-2-methyl-3-yne (197) with catecholborane (198) gives the 1,4-adduct 199 with 84% selectivity. The ratio of Pd to phosphine (1 1.5) is important[l 10]. The vinyl sulfide 201 is prepared by a one-pot reaction of the thioalkyne 200 via a Pd-catalyzed hydroborution-coupling sequence using dppf as a ligand[l 11]. 

Addition of nucleophiles to both activated and unactivated alkenes is catalyzed by Pd(II). Addition of alcohols or AcOH to alkenes bearing EWGs is catalyzed by PdCl2(PhCN)2 to give the corresponding ethers and esters. The addition of an alcohol to the cyclic acetal of acrolein 82 to give the ether 83 is also possible with the same catalyst[64]. Amines add to the vinylic ether 84 to give 85, but not to simple alkenes[65]. 

Intramolecular palladium-catalysed cyclizations can also be applied to N-vinylanilines. Usually the vinyl group carries an EW substituent which serves... 

The photocyclization of iV-vinylanilines is an e.xarnple of a general class of photocyclizations[l]. If the vinyl substituent has a potential leaving group or the reaction is carried out so that oxidation occurs, the cyclization intermediate can aromatize to an indole. 

As illustrated in Scheme 8.1, both 2-vinylpyrroles and 3-vinylpyiroles are potential precursors of 4,5,6,7-tetrahydroindolcs via Diels-Alder cyclizations. Vinylpyrroles are relatively reactive dienes. However, they are also rather sensitive compounds and this has tended to restrict their synthetic application. While l-methyl-2-vinylpyrrole gives a good yield of an indole with dimethyl acetylenedicarboxylate, ot-substitiients on the vinyl group result in direct electrophilic attack at C5 of the pyrrole ring. This has been attributed to the stenc restriction on access to the necessary cisoid conformation of the 2-vinyl substituent[l]. 

Donor substituents on the vinyl group further enhance reactivity towards electrophilic dienophiles. Equations 8.6 and 8.7 illustrate the use of such functionalized vinylpyrroles in indole synthesis[2,3]. In both of these examples, the use of acetyleneic dienophiles leads to fully aromatic products. Evidently this must occur as the result of oxidation by atmospheric oxygen. With vinylpyrrole 8.6A, adducts were also isolated from dienophiles such as methyl acrylate, dimethyl maleate, dimethyl fumarate, acrolein, acrylonitrile, maleic anhydride, W-methylmaleimide and naphthoquinone. These tetrahydroindole adducts could be aromatized with DDQ, although the overall yields were modest[3]. 

The monomer bearing the vinyl group is synthesized and then polymerized. The most common monomers are of the type shown in Scheme 9 (312, 313). 

Any discussion based on reactivity ratios is kinetic in origin and therefore reflects the mechanism or, more specifically, the transition state of a reaction The transition state for the addition of a vinyl monomer to a growing radical involves the formation of a partial bond between the two species, with a corre sponding reduction of the double-bond character of the vinyl group in the monomer ... 

It is proposed to polymerize the vinyl group of the hemin molecule with other vinyl comonomers to prepare model compounds to be used in hemoglobin research. Considering hemin and styrene to be species 1 and 2, respectively, use the resonance concept to rank the reactivity ratios rj and X2. 

Other fairly recent commercial products, poly(vinyl amine) and poly(vinyl amine vinyl alcohol), have addressed the need for primary amines and their selective reactivity. Prior efforts to synthesize poly(vinyl amine) have been limited because of the difficulty hydrolyzing the intermediate polymers. The current product is prepared from /V-ethenylformamide (20) formed from the reaction of acetaldehyde and formamide. The vinyl amide is polymerized with a free-radical initiator, then hydrolyzed (eq. 7). 

---