The Hardware

The hardware items with which the processes described in Section 10.1 are achieved are called facilities, and are designed by the facilities engineer. The previous section described the equipment items used for the main processes such as separation, drying, fractionation, compression. This section will describe some of the facilities required for the systems which support production from the reservoir, such as gas injection, gas lift, and water injection, and also the transportation facilities used for both offshore and land operations. 

Within the project box, the cashflow oi the project (or other investment opportunity) is the forecast of the funds absorbed and the money generated during the project lifetime. Take, for example, the development of an oil field as the investment opportunity. Initially the cashflow will be dominated by the capital expenditure (capex) required to design, construct and commission the hardware for the project (e.g. platform, pipeline, wells, compression facilities). 

During the design phase, facilities (the hardware items of equipment) are designed for operating conditions which are anticipated based upon the information gathered during field appraisal, and upon the outcome of studies such as the reservoir simulation. The design parameters will typically be based upon assessments of... 

Hardware problems as the instruments have rather poor processors and custom architecture, it is difficult to test new configurations and, once the new configuration is selected, it is often necessary to strongly modify the hardware in order to adapt the existing instruments. 

For the hardware, there is a flash memory on each eddy current board. The user can ask the following information ... 

The great advantage of installing an ultrasonic system in a PC is that both the hardware (processor, grafics, power supply,. .) aud the software (evaluation and documentation) are directly available for the inspections. 

It can be said that these three main strategies have been applied equally and very often in combination. Basically, the first approach implies the use of a faster computer or a parallel architecture. To some extent it sounds like a brute force approach but the exponential increase of the computer power observed since 1970 has made the hardware solution one of the most popular approaches. The Chemical Abstracts Service (CAS) [10] was among first to use the hardware solution by distributing the CAS database onto several machines. 

Xps ndAes Instrumentation. The instmmentation required to perform xps and aes analyses is generally sophisticated and expensive (19). The need for UHV conditions in order to retain surface cleanliness for a tractable period of time was mentioned above. Beyond this requirement (and the hardware that accompanies it), the most important components of an electron spectrometer system are the source, the electron energy analyzer, and the electron detector. These will be discussed in turn below. 

Ohmic Drops. Another irreversible contribution to the measured cell voltage is the ohmic or JR drop across the electrolyte, separator, and cell hardware. The JR drop across the hardware can be estimated from Ohm s law and the relationship... 

Again, irrespective of the hardware the chemistry is consistent. The partially regenerated fiber from the spinning machine is contaminated with sulfuric acid, 2inc sulfate, sodium sulfate, carbon disulfide, and the numerous incompletely decomposed by-products of the xanthation reactions. The washing and drying systems must yield a pure cellulose fiber, suitably lubricated for the end use, and dried to a moisture level of around 10%. 

Impedance. Impedance defines the relationship of voltage and current in a coaxial cable. The electrical requirements of the hardware dictate the impedance values for the interconnecting cables. Most coaxial cables are designed to match the impedances required by electronic hardware. 

AH columns, distributors, and ancHlary hardware such as piping, valves, and pumps must be constmcted of corrosion-resistant materials, or coated with an appropriate substance. AH streams that contact the hardware during each step of the cycHc operation need to be considered in this selection. 

The business activity of the organi2ation dictates quaUty requirements for the LIMS. Security and regulatory requirements for LIMS data define the level of effort expended to vahdate a LIMS and the data being stored. In addition, the quahty of the hardware and software used to implement the LIMS both play a role in determining overall system quahty. 

The hardware and software used to implement LIMS systems must be vahdated. Computers and networks need to be examined for potential impact of component failure on LIMS data. Security concerns regarding control of access to LIMS information must be addressed. Software, operating systems, and database management systems used in the implementation of LIMS systems must be vahdated to protect against data cormption and loss. Mechanisms for fault-tolerant operation and LIMS data backup and restoration should be documented and tested. One approach to vahdation of LIMS hardware and software is to choose vendors whose products are precertified however, the ultimate responsibihty for vahdation remains with the user. Vahdating the LIMS system s operation involves a substantial amount of work, and an adequate vahdation infrastmcture is a prerequisite for the constmction of a dependable and flexible LIMS system. 

A catalyst manufactured using a shaped support assumes the same general size and shape of the support, and this is an important consideration in the process design, since these properties determine packing density and the pressure drop across the reactor. Depending on the nature of the main reaction and any side reactions, the contact time of the reactants and products with the catalyst must be optimized for maximum overall efficiency. Since this is frequendy accompHshed by altering dow rates, described in terms of space velocity, the size and shape of the catalyst must be selected carehiUy to allow operation within the capabiUties of the hardware. 

Ensuring the integrity of process controls involves both hardware issues, software issues, and human issues. Of these, the hardware issues are usually the easiest to assess and the software issues the most difficult. 

Because indirect-heat calciners frequently require close-fitting gas seals, it is customaiy to support aU parts on a selFcontained frame, for sizes up to approximately 2 m in diameter. The furnace can employ elec tric heating elements or oil and/or gas burners as the heat source for the process. The hardware would be zoned down the length of the furnace to match the heat requirements of the process. Process control is normaUy by shell temperature, measured by thermocouples or radiation pyrometers. When a special gas atmosphere must be maintained inside the cyhnder, positive rotaiy gas se s, with one or more pressurized and purged annular chambers, are employed. The diaphragm-type seal ABB Raymond (Bartlett-Snow TM) is suitable for pressures up to 5 cm of water, with no detectable leakage. 

The fault ctirrents also develop electrodynamic foi ces, Fii, as in equation (28.4) due to the sub-transient d.c. component. These forces play an important role in the meehanical design of the interrupting device, the load-bearing and mounting structuies for the interrupter and the bus system, and the hardware used in a switchgear assembly. All such mechanical parts, supports and hardw-are should be adequate to withstand such forces when they arise, A procedure to arrive at the ideal size of the current-carrying components, mounting structure, type of supports and hardware cte, is discussed in detail in Example 28.12. 

Before diseussing the turbomaehinery management attributes of digital systems, it is helpful to review the hardware, software, and MACS PACK eomponents. 

Dye penetrant inspection of the hardware to determine the extent of distress in order to develop material requirements and repair techniques. 

San Diego Gas Electric s system was originally installed as a research project. The intent of the research project was to test the hardware in this application, test the feasibility of operating such a system remotely with no local operators, and to prove the economics. Similar systems had been installed within process plants where operators were present to start and stop the system and monitor its operation. However, this was the first system installed on a natural gas transmission system with completely remote operation. 

All commercially available SIMS systems have in common some type of computer automation, an ion source, a high-vacuum environment, and some type of mass spectrometer. While the specifics may vary from system to system, the basic requirements are the same. The hardware feature that tends to distii uish the various systems is the type of mass spectrometer used. These fall into three basic catego-... 

This volume is a departure from the style of technical writing that I and many of my colleagues have done in the past. What I have attempted is to discuss the subject, rather than to try and teach or summarize the technologies, the hardware, and selection criteria for different equipment. It s a subject to discuss and explore, rather than to present in a dry, strictly technical fashion. Water treatment is not... 

---