Temperature polyolefins

Depending on the starting materials (monomers) and the density (processing temperature), polyolefins may be classified according to the following principal groups ... 

Biocide Water Solubility mg/1 (ppm) Heat stable in higher temperature polyolefins Heat stable in most PVC, PU and lower temperature plastics UV stability (discoloration) Index of solubility (MIC/solubility in water)... 

There exist two obvious ways of increasing the active solids content of an adhesive effectively to 100% use of Hot melt adhesives and Reaction setting adhesives. The main constituent of hot melts is a thermoplastic polymer that may be blended with thermoplastic modifiers and extenders and inert fillers to create a system that is a load-bearing solid at the service temperature but a mobile liquid at the (higher) application temperature. Polyolefins, ionomers, polyesters and polyamides are among the polymer types that have been used as bases for Hot melt adhesives. 

Polyolefins are considered to be the best choice for blending with NR on account of their high softening temperature and low glass transition temperature, which result in a versatile end product and are applicable over a wide range of temperature. Polyolefin-based NR blend compositions (HDPE/NR, PP/NR) can... 

Because of the high melt viscosity of polyolefins, normal spinning melt temperatures are 240—310°C, which is 80—150°C above the crystalline melting point. Because of the high melt temperatures used for polyolefin fiber spinning, thermal stabilizers such as substituted hindered phenols are added. In the presence of pigments, the melt temperature must be carefully controlled to prevent color degradation and to obtain uniform color dispersion. 

Phase Separation. Microporous polymer systems consisting of essentially spherical, intercoimected voids, with a narrow range of pore and ceU-size distribution have been produced from a variety of thermoplastic resins by the phase-separation technique (127). If a polyolefin or polystyrene is insoluble in a solvent at low temperature but soluble at high temperatures, the solvent can be used to prepare a microporous polymer. When the solutions, containing 10—70% polymer, are cooled to ambient temperatures, the polymer separates as a second phase. The remaining nonsolvent can then be extracted from the solid material with common organic solvents. These microporous polymers may be useful in microfiltrations or as controlled-release carriers for a variety of chemicals. 

The TPX experimental product of Mitsubishi Petrochemical Ind. (221) is an amorphous, transparent polyolefin with very low water absorption (0.01%) and a glass-transition temperature comparable to that of BPA-PC (ca 150°C). Birefringence (<20 nm/mm), flexural modulus, and elongation at break are on the same level as PMMA (221). The vacuum time, the time in minutes to reach a pressure of 0.13 mPa (10 torr), is similarly short like that of cychc polyolefins. Typical values of TPX are fisted in Table 11. A commercial application of TPX is not known as of this writing. 

Fig. 26. Qualitative compatison of substrate materials for optical disks (187) An = birefringence IS = impact strength BM = bending modulus HDT = heat distortion temperature Met = metallizability WA = water absorption Proc = processibility. The materials are bisphenol A—polycarbonate (BPA-PC), copolymer (20 80) of BPA-PC and trimethylcyclohexane—polycarbonate (TMC-PC), poly(methyl methacrylate) (PMMA), uv-curable cross-linked polymer (uv-DM), cycHc polyolefins (CPO), and, for comparison, glass.

Above 100°C, most polyolefins dissolve in various aHphatic and aromatic hydrocarbons and their halogenated derivatives. For example, polybutene dissolves in benzene, toluene, decalin, tetralin, chloroform, and chlorobenzenes. As with other polyolefins, solubiHty of PB depends on temperature, molecular weight, and crystallinity. 

Polymorphism. Many crystalline polyolefins, particularly polymers of a-olefins with linear alkyl groups, can exist in several polymorphic modifications. The type of polymorph depends on crystallisa tion conditions. Isotactic PB can exist in five crystal forms form I (twinned hexagonal), form II (tetragonal), form III (orthorhombic), form P (untwinned hexagonal), and form IP (37—39). The crystal stmctures and thermal parameters of the first three forms are given in Table 3. Form II is formed when a PB resin crystallises from the melt. Over time, it is spontaneously transformed into the thermodynamically stable form I at room temperature, the transition takes about one week to complete. Forms P, IP, and III of PB are rare they can be formed when the polymer crystallises from solution at low temperature or under pressure (38). Syndiotactic PB exists in two crystalline forms, I and II (35). Form I comes into shape during crystallisation from the melt (very slow process) and form II is produced by stretching form-1 crystalline specimens (35). 

Electrical Properties. AH polyolefins have low dielectric constants and can be used as insulators in particular, PMP has the lowest dielectric constant among all synthetic resins. As a result, PMP has excellent dielectric properties and alow dielectric loss factor, surpassing those of other polyolefin resins and polytetrafluoroethylene (Teflon). These properties remain nearly constant over a wide temperature range. The dielectric characteristics of poly(vinylcyclohexane) are especially attractive its dielectric loss remains constant between —180 and 160°C, which makes it a prospective high frequency dielectric material of high thermal stabiUty. 

Analytical and test methods for the characterization of polyethylene and PP are also used for PB, PMP, and polymers of other higher a-olefins. The C-nmr method as well as k and Raman spectroscopic methods are all used to study the chemical stmcture and stereoregularity of polyolefin resins. In industry, polyolefin stereoregularity is usually estimated by the solvent—extraction method similar to that used for isotactic PP. Intrinsic viscosity measurements of dilute solutions in decahn and tetraHn at elevated temperatures can provide the basis for the molecular weight estimation of PB and PMP with the Mark-Houwiok equation, [rj] = KM. The constants K and d for several polyolefins are given in Table 8. 

Tables 4—6 Ust ASTM methods used for the characterization of PB and PMP. A number of specialized methods were developed for testing particular articles manufactured from polyolefins several of these determine the performance of PB and PMP film, including the measurement of the film s dart impact strength and tear strength. Dart impact strength is measured by dropping a heavy dart with a round tip on a stretched film. Tear resistance, which reflects the film s resistance to tear propagation, is measured with the Ehnendorf tear tester. Two values for the tear strength are usually reported, one in the machine dkection of the film and the other in the transverse dkection. Pipes manufactured from PB are tested by pressurizing them internally with water the time-to-burst failure is determined at various temperatures (46). The standard test method for haze and luminous transmittance (ASTM D1003) is used for the measurement of PMP optical characteristics.

---