Temperature control exothermicity

Temperature control. Let us now consider temperature control of the reactor. In the first instance, adiabatic operation of the reactor should be considered, since this leads to the simplest and cheapest reactor design. If adiabatic operation produces an unacceptable rise in temperature for exothermic reactions or an unacceptable fall in temperature for endothermic reactions, this can be dealt with in a number of ways ... 

Generally speaking, temperature control in fixed beds is difficult because heat loads vary through the bed. Also, in exothermic reactors, the temperature in the catalyst can become locally excessive. Such hot spots can cause the onset of undesired reactions or catalyst degradation. In tubular devices such as shown in Fig. 2.6a and b, the smaller the diameter of tube, the better is the temperature control. Temperature-control problems also can be overcome by using a mixture of catalyst and inert solid to effectively dilute the catalyst. Varying this mixture allows the rate of reaction in different parts of the bed to be controlled more easily. 

A typical flow diagram for pentaerythritol production is shown in Figure 2. The main concern in mixing is to avoid loss of temperature control in this exothermic reaction, which can lead to excessive by-product formation and/or reduced yields of pentaerythritol (55,58,59). The reaction time depends on the reaction temperature and may vary from about 0.5 to 4 h at final temperatures of about 65 and 35°C, respectively. The reactor product, neutralized with acetic or formic acid, is then stripped of excess formaldehyde and water to produce a highly concentrated solution of pentaerythritol reaction products. This is then cooled under carefully controlled crystallization conditions so that the crystals can be readily separated from the Hquors by subsequent filtration. 

In contrast to the silver process, all of the formaldehyde is made by the exothermic reaction (eq. 23) at essentially atmospheric pressure and at 300—400°C. By proper temperature control, a methanol conversion greater than 99% can be maintained. By-products are carbon monoxide and dimethyl ether, in addition to small amounts of carbon dioxide and formic acid. Overall plant yields are 88—92%. 

Chlorine free radicals used for the substitutioa reactioa are obtaiaed by either thermal, photochemical, or chemical means. The thermal method requites temperatures of at least 250°C to iaitiate decomposition of the diatomic chlorine molecules iato chlorine radicals. The large reaction exotherm demands close temperature control by cooling or dilution, although adiabatic reactors with an appropriate diluent are commonly used ia iadustrial processes. Thermal chlorination is iaexpeasive and less sensitive to inhibition than the photochemical process. Mercury arc lamps are the usual source of ultraviolet light for photochemical processes furnishing wavelengths from 300—500 nm. 

With batch reactors, it may be possible to add all reactants in their proper quantities initially if the reaction rate can be controlled by injection of initiator or acqustment of temperature. In semibatch operation, one key ingredient is flow-controlled into the batch at a rate that sets the production. This ingredient should not be manipiilated for temperature control of an exothermic reactor, as the loop includes two dominant lags—concentration of the reactant and heat capacity of the reaction mass—and can easily go unstable. 

Phthalic anhydride. Naphthalene is oxidized by air to phthalic anhydride in a Bubbling flmdized reaclor. Even though the naphthalene feed is in liquid form, the reaction is highly exothermic. Temperature control is achieved by removing heat through vertical tubes in the bed to raise steam [Graham and Way, Chem. Eng. Prog., 58, 96 (Januaiy 1962)]. 

Acrylonitrile. Acrylonitrile is produced by reacting propylene, ammonia, and owgeu (air) in a single flmdized bed of a complex catalyst. Known as the SOHIO process, this process was first operated commercially in 1960. In addition to acrylonitrile, significant quantities of HCN and acetonitrile are also produced. This process is also exothermic. Temperature control is achieved by raising steam inside vertical tubes immersed in the bed [Veatch, Hydrocarbon Proce.ss. Pet. Refiner, 41, 18 (November 1962)]. 

The Fischer-Tropsch reaction is highly exothermic. Therefore, adequate heat removal is critical. High temperatures residt in high yields of methane, as well as coking and sintering of the catalyst. Three types of reac tors (tubular fixed bed, fluidized bed, and slurry) provide good temperature control, and all three types are being used for synthesis gas conversion. The first plants used tubular or plate-type fixed-bed reactors. Later, SASOL, in South Africa, used fluidized-bed reactors, and most recently, slurry reactors have come into use. 

Nitration Hazards arise from the strong oxidizing nature of the nitrating agents used (e.g. mixture of nitric and sulphuric acids) and from the explosive characteristics of some end products Reactions and side reactions involving oxidation are highly exothermic and may occur rapidly Sensitive temperature control is essential to avoid run-away... 

Older cook styles called for addition of phenol, formaldehyde, and water followed by alkali. Once the alkali was added, strict temperature control was the only barrier to a runaway reaction. A power or equipment failure at this point was likely to lead to disaster. Every batch made involved a struggle between the skill of the operator and capability of the equipment to control the exotherm versus the exothermic nature of the reactants. Most of the disasters that have occurred were due to utilization of this cooking method. 

Commercial Fischer-Tropsch processes have been based exclusively on gas-particle operations, mainly in fixed beds (P2). The chemical reactions are highly exothermic, however, and accurate temperature control is therefore difficult to achieve in a fixed bed. Good temperature control is important because of the temperature sensitivity of the chemical reactions taking place, and several attempts have therefore been made to develop processes based on other types of operation. 

From these general characteristics a number of criteria for sulfonation configurations can be derived. The combination of an instantaneous reaction, with considerable exothermic heat effect and a factor 50-100 increase in viscosity in the organic phase, makes it clear that proper temperature control in the organic phase is the main problem in practice. 

Temperature control of a large, highly exothermic semi-batch chemical or polymer reactor can be an involved problem. The reaction may be auto-acceleratlng. Heat transfer rates can vary during the process. Random disturbances can enter the process from many sources. Changes In... 

Exothermic reactions require control strategies which may involve temperature control, dilution of reagents, controlled addition of one reagent, containment/venting and provision for emergencies. Refer to p. 248. 

Another industrially important reaction of propylene, related to the one above, is its partial oxidation in the presence of ammonia, resulting in acrylonitrile, H2C=CHCN. This ammoxidation reaction is also catalyzed by mixed metal oxide catalysts, such as bismuth-molybdate or iron antimonate, to which a large number of promoters is added (Fig. 9.19). Being strongly exothermic, ammoxidation is carried out in a fluidized-bed reactor to enable sufficient heat transfer and temperature control (400-500 °C). 

We have also constructed a cell that permits close temperature control, even for exothermic reactions. In it, a sample can be heated to as high as 800 K, treated and then cooled to as low as 140 K, all in situ on the diffractometer (9). 

P 9] DL-l-Phenylethylamine and 4-amino-l-benzylpiperidine were dissolved in 0.1 M NaOH aqueous solution [23]. 3-Nitrobenzoyl chloride and 3,5-dinitrobenzoyl chloride were used as ethyl acetate solutions. The concentration of all reactants was set to 0.01 M. Syringe pumps served for liquid feed. The flow rate was 50 plmin and room-temperature processing was applied. No further temperature control was exerted as the reaction is only mildly exothermic. After having passed the micro reactor, the phases were settled in test-tubes and the organic phase was withdrawn for analysis. 

---