TEGDMA dimethacrylate

Tetraethylene glycol dimethacrylate (TEGDMA), 43 733, 734 Tetraethylene glycol bis(allyl carbonate) properties of, 2 253t T etr aethylenepentamine physical properties, 8 486t... 

Compomers contain no water, but rather are mainly formulated from the same components as conventional composite resins. Typically this means macromonomers, such as bis-glycidyl ether dimethacrylate (bisGMA) or its derivatives and/or urethane dimethacrylate, blended with viscosity-reducing diluents, such as triethylene glycol dimethacrylate (TEGDMA). These polymer systems are filled with non-reactive inorganic powders, for example, quartz or a silicate glass [271]. 

The majority of resins are composed of two dimethacrylate monomers, 2,2 -bis [4(2-hydroxy-3-methacryloyloxypropyloxy)phenyl] propane (Bis-GMA) and triethylene glycol dimethacrylate (TEGDMA) [22-28]. Typically, TEGDMA or other methacrylate monomers are added as viscosity modifiers to Bis-GMA to make the solution less viscous and more appropriate for clinical use. These diluents also allow for better distribution of the components during manufacture of these composite systems. Another common monomer used to make dental composites, especially those manufactured in Europe, is urethane dimethacrylate [24,29, 30], Ethoxy bisphenol A dimethacrylate is another modification of the Bis-GMA monomer that can be used to make a more hydrophobic polymer that would better withstand the wet oral environment. Other diluents include low viscosity diacrylates and dimethacrylates. Table 1 lists some of these monomers [31-37]. 

For instance, conductometric transduction has been used for determination of an atrazine herbicide in the concentration range 4.6-231.8 mM [165]. A sintered glass frit was used as the support for the MIP film prepared by thermo-radical polymerization. However, both the response time of 30 min and the chemosensor recovery time of 12 h were long. For better performance, the MIP film was prepared by photo-radical co-polymerization of a chloroform solution, which contained tri (ethylene glycol)dimethacrylate (TEGDMA), MAA, and oligourethane acrylate, sandwiched between two quartz slides (Table 6). 

In the last generation endodontic and restorative materials molecules such as 2-hydroxyethylmethacrylate (HEMA), triethyleneglycol dimethacrylate (TEGDMA) and 2,2-bis[4-(2-hydroxy-3-methacryloxy)-phenyl]propane (Bis-GMA) are present. In the clinical use these compounds are chemically or photochemically polymerised and the degree of polymerization - which is never complete - determines the release of some quantity of uncured monomers in the pulpar cavity. Thus, the pulpal tissues can be exposed - through the dentinal diffusion - to these compounds that may cause inflammatory reactions and cellular damage, as confirmed by several reports. ... 

Diethylene glycol dimethacrylate (DEGDMA) divinyl benzene (DVB) tetraethylene glycol dimethacrylate (TEGDMA) glycidyl methacrylate (GMA) maleic anhydride (MA). 

PMMA and other methacrylate and acrylate polymers are widely used in dentistry. PMMA is used for dentures and root canal sealants. Polymers of 2,2-bis[4-(2-hydroxy-3-methacry-loyolxypropoxy)phenyl]propane (BisGMA), triethyleneglycol dimethacrylate (TEGDMA), and urethane dimethacrylate (UDMA) are used in dental composite resins, most commonly with a silica filler. Such composite resins are used for filling cavities, reshaping, and restoring teeth and for full and partial crowns. 

Bisomer SR. See 2-Hydroxyethyl methacrylate Bisomer TEGDMA. See PEG-3 dimethacrylate Bisomer TMPTMA Rubber Grade] Bisomer TMPTMA. See 1,1,1-Trimethylolpropane trimethacrylate... 

Acrylic polymers are one of the important structural adhesives (Fig. 11). These polymers can be classified as anaerobic structural acrylics (60), second generation acrylics (60,61), and aerobic acrylics (61,62). Most anaerobic adhesives are based on dimethacrylic esters, e.g., TEGDMA (triethylene glycol dimethacrylate) (Fig. 12). Anaerobic adhesives (63) containing maleimides have been reported to have improved thermal resistance. 

---