Synthetic polymers phosphoric acid

Depressants are used to make materials less floatable, and again have been used for some time.4,18 A recent example is the use of phosphoric acid to depress the flotation of a sedimentary phosphate ore, enhancing the selectivity of recovery of calcite and silica.24 Natural and synthetic polymers have also been used as depressants.20... 

Direct copolymerization of sulfonated monomers has been used to synthesize sulfonated poly (benzimidazoles), poly(benzoxazole)s, and poly(benzothia-zole)s. As an example, Kim et al. synthesized poly-(benzthiazole)s from 2,5-diamino-1,4-benzenedithiol dihydrochloride and either 2-sulfoterethphthalic acid sodium salt, 5-sulfoisophthalic acid sodium salt, or 2,4-disulfoisophthalic acid potassium salt in poly-phosphoric acid (PPA), as shown in Figure 34. Similar sulfonated poly(benzimidazole) and sulfonated poly(benzoxazole) ° structures have also been synthesized. A general synthetic scheme for each is shown in Figure 35. The stability of these polymers in aqueous acidic environments appears... 

Dutton and Unrau188 studied synthetic polymers obtained by the technique of heating the sugar with phosphorous acid.188 These products... 

Abstract. Several series of pyrocarbon/silica adsorbents were prepared using fumed oxides of different specific surface areas, and mesoporous silica gel Si-100, as inorganic matrices. Different synthetic and natural polymers as well as glucose were used as carbon precursors. Solutions of phosphoric acid at various concentrations were utilized to prepare functionalized hybrid carbon-silica adsorbents. Nitrogen, p-nitrophenol and Cd(II) adsorption isotherms as well as AFM, XRD and XRF methods were used to estimate the structural and adsorption characteristics of the adsorbents. 

Polymerization of cyclic esters of phosphoric acid (cyclic phosphates) is interesting from the synthetic point of view, because the resulting polymers have the sequence of atoms of the chain identical with this, which appears in important biopolymers such as nucleic or teichoic acids. Both 5- and 6-membered cyclic phosphates undergo polymerization. 

The results of these studies and others reported previously demonstrate that the 1-oxypyridinyl group is an effective catalyst for the transacylation reactions of derivatives of carboxylic and phosphoric acids when incorporated in small molecules and polymers. Furthermore, this catalytic site exhibits high selectivity for acid chlorides in the presence of acid anhydrides, amides, and esters. Therefore, catalysts bearing this group as the catalytic site can be used successfully in synthetic applications that require such specificity. The results of this work suggest that functionalized polysiloxanes should be excellent candidates as catalysts for a wide variety of chemical reactions, because they combine the unique collection of chemical, physical, and dynamic-mechanical properties of siloxanes with the chemical properties of the functional group. Finally, functionalized siloxanes appear to mimic effectively enzyme-lipophilic substrate associations that contribute to the widely acknowledged selectivity and efficiency observed in enzymic catalysis. 

Fire-resistant water polymer solutions containing minimum 35% mass water Fire-resistant synthetic fluids based on phosphoric acid esters Fire-resistant synthetic fluids of other types... 

The in situ construction of the inorganic component within a cast polymer solution is not limited to metal oxides and in practice a range of other inorganic materials can be formed depending on the choice of precursor(s) incorporated in the polymer solution, and the nature of post-treatment following solvent removal. Roziere and Jones and co-workers have developed nano composite membranes in which zirconium phosphate is formed from zirconyl propionate introduced into a DMAc solution of sPEEK, by immersion of the cast film, after solvent removal, into phosphoric acid. This approach provides a robust synthetic route that can be generalised to other ionomers, and allows the amount of ZrP to be readily varied, even up to ca. 40-50 wt. %. 

Butyl alcohol Dimethyl amine Ethylene n-Heptadecanol Phosphoric acid detergent mfg., dry cleaning Diceteareth-10 phosphate detergent mfg., powder Ceteareth-18 PEG-2 tallate PEG-7 tallate detergent mfg., synthetic Pentylamine detergent polymer Acrylates copolymer... 

Various phosphates are produced from phosphoric acid which is made either by adding sulphuric acid to phosphate rock (wet process) or by burning phosphorus in air to give phosphorus pentoxide, which is then hydrated. Major uses of phosphoric acid are the production of phosphate and compound fertilizers, formation of sodium tripolyphosphate (which is used as a builder in detergents where it forms stable water-soluble complexes with calcium and magnesium ions) and the production of organic derivatives like triphenyl and tricresyl phosphate. These are used as plasticizers for synthetic polymers and plastics. 

Several materials have been proposed and commercialized as electrolytes for HT-PEFCs. As introduced before, the main polymers used materials from the PBI family and the Advent tetramethyl pyridine sulfone (TPS) family, both being basic polymers allowing chemical interaction with mineral acids (e.g., phosphoric acid) see Fig. 1. Differences can be fotmd both in the chemistry and in the synthetic process especially among the different PBIs, yielding different physicochemical properties such as glass transition temperatures, mechanical stabilities, proton conductivities, and achievable phosphoric acid doping levels (defined as either the ratio of phosphoric acid molecules per polymer repeat unit or the weight ratio of polymer and included phosphoric acid) for a summary, see Table 1. 

There are many polymers that are suitable for the production of nanoparticles employed for drug delivery, which can generally be divided into two groups natural polymers, e.g., polysaccharides (chitosan), proteins (albumin, gelatin), as well as synthetic polymers, e.g., polyesters (poly(lactic add), poly(glycolic add), poly(hydroxy butyrate), poly-e-caprolactone, poly-p-malic add, poly(dioxanones)) polyanhydrides (poly(adipic add)) polyamides (poly(amino acids)) phosphorous-based polymers (polyphosphate) poly(cyano acrylates) polyurethanes polyortho esters and polyacetals. Extreme attention has to be paid to the biodegradability and biocompatibility of the polymers. It is essential that polymers used for medical applications are not detrimental for the tissue or cells and that they can be easily decomposed into simple harmless molecules and eliminated by the human body [ 18-22]. 

---