Surface specific applications

The maximum surface temperature must remain below the temperature class specified in Table 7.4 for a specific application. 

Condensers may be of one or two general types depending on the specific application. Contact condensers operate with the coolant, vapors, and condensate intimately mixed. In surface condensers, the coolant does not come in contact with either the vapors or the condensate. The usual shell-and-tube condenser is of the surface type. Figure 29-14 illustrates a contact condenser which might be used to clean or preclean a hot corrosive gas. 

Some of the techniques included apply more broadly than just to surfaces, interfaces, or thin films for example X-Ray Diffraction and Infrared Spectroscopy, which have been used for half a century in bulk solid and liquid analysis, respectively. They are included here because they have by now been developed to also apply to surfaces. A few techniques that are applied almost entirely to bulk materials (e.g.. Neutron Diffraction) are included because they give complementary information to other methods or because they are referred to significantly in the 10 materials volumes in the Series. Some techniques were left out because they were considered to be too restricted to specific applications or materials. 

For a number of purposes the unmodified epoxide resins may be considered to have certain disadvantages. These disadvantages include high viscosity, high cost and too great a rigidity for specific applications. The resins are therefore often modified by incorporation of diluents, fillers, and flexibilisers and sometimes, particularly for surface coating applications, blended with other resins. 

Tubing used to convey fluids at elevated temperatures and/or pressures. Suitable for head applications, it is fabricated to exact o.d. and decimal wall tliickness in sizes ranging from V2-6 in. o.d. inclusive and to ASTM specifications. Coating that is applied to a surface before application of an adhesive, enamel, etc. The purpose is to improve bonding. 

Rim exhausts are a specific application of slot hoods, which in turn are a type of exterior or capture hood. Rim exhausts are slot hoods placed along the rim or edge of an area source such as an open surface tank or vessel opening. Open surface tanks are widely used in indu.strial settings for cleaning, stripping. 

Surface resistivity is the ratio of the potential gradient parallel to the current along its surface to the current per unit width of the surface. Knowing the volume and surface resistivity of an insulating material makes it possible to design an insulator for a specific application. 

Cycloaddition reactions with the Si(lOO) surface have been investigated for the purpose of designing microelectronics, nonlinear optical materials, sensors, and biologically active surfaces. The features of the [2+2] cycloadditions characteristic of the reactions in the pseudoexcitation band [133] predicts that [2+2] cycloadditions of electron-donating alkenes with Si(100)-2 x 1 surface could proceed with retention of configurations, in agreement with the observation [134]. Such stereospecific functionalizations of surfaces are of potential use for specific applications. 

The surface actlve/surface inactive difference between p-polarlsed/ s-polarised radiation has enabled an alternative modulation technique, polarisation modulation, to be developed (15,16). In electrochemical applications, it allows surface specificity to be achieved whilst working at fixed potential and without electrochemical modulation of the interface. It can be implemented either on EMIRS or on SNIFTIRS spectrometers and can be very valuable in dealing with electrochemically irreversible systems however, the achievable sensitivity falls well short of that obtained with electrochemical modulation. It should also be noted that its "surface specificity" is not truly surface but extends out into the electrolyte with decreasing specificity to about half a wavelength. 

The number of sub-samples that must be obtained for individual speleothems depends on the specific application. When ages are to be used to constrain the periods of continuous growth or hiatuses, sub-samples from the base and outer surface may suffice. For applications based on high-resolution records of environmental change, a suite of ages must be obtained to estimate the distance-age relationship along the axis of growth. 

Carbon is inert in nature and has a high surface area, making it highly suitable as a support for catalysts. The surface characteristics and porosity of carbon may be easily tailored for different applications. Acid treatment is often applied to modify its surface chemistry for specific applications. Typically, active metal species are immobilized on carbon for catalytic applications. 

In addition to the particulate adsorbents listed in Table 16-5, some adsorbents are available in structured form for specific applications. Monoliths, papers, and paint formulations have been developed for zeolites, with these driven by the development of wheels (Fig. 16-60), adsorptive refrigeration, etc. Carbon monoliths are also available as are activated carbon fibers, created from polymeric materials, and sold in the forms of fabrics, mats, felts, and papers for use in various applications including in pleated form in filters. Zeolitic and carbon membranes are also available, with the latter developed for separation by selective surface flow [Rao and Sircar, J. Membrane Sci., 85, 253 (1993)]. 

Molecular sieves are synthetic zeolites that can be manufactured with extremely close control of pore size. Therefore, they can be tailored to suit specific applications. In addition to gas drying applications, molecular sieves are used for the separation of gases and vapors on the basis of molecular size and shape. Surface areas range from 350 to 1000 ft2/ft3. 

---