Surface area/volume

A number of properties can be computed from various chemical descriptors. These include physical properties, such as surface area, volume, molecular weight, ovality, and moments of inertia. Chemical properties available include boiling point, melting point, critical variables, Henry s law constant, heat capacity, log P, refractivity, and solubility. 

E] Gas absorption aud desorption from water aud organics plus vaporization of pure liquids for Raschig riugs, saddles, spheres, aud rods, dp = nominal pacldug size, Cp = dry pacldug surface area/volume, = wetted pacldug surface area/volume. Equations are dimensionally consistent, so any set of consistent units can be used. <3 = surface tension, dynes/cm. 

Direct bonding. In many high-volume production applications (i.e., the automotive and appliance industries), elaborate surface preparation of steel ad-herends is undesirable or impossible. Thus, there has been widespread interest in bonding directly to steel coil surfaces that contain various protective oils [55,56,113-116], Debski et al. proposed that epoxy adhesives, particularly those curing at high temperatures, could form suitable bonds to oily steel surfaces by two mechanisms (1) thermodynamic displacement of the oil from the steel surface, and (2) absorption of the oil into the bulk adhesives [55,56]. The relative importance of these two mechanisms depends on the polarity of the oil and the surface area/volume ratio of the adhesive (which can be affected by adherend surface roughness). 

In vivo biocompatibility was assessed through subcutaneous implantation in Sprague-Dawley rats. PLGA was used as a control polymer. PGS and PLGA implants with the same surface area/volume ratio were implanted in dorsal subcutaneous pockets. A fibrous capsule around PGS (45 pm thick after 35 days implantation) appeared later than that around PLGA (140 pm thick after 14 days implantation). After 60 days of implantation, the implant was completely absorbed with no signs of granulation or scar formation. ... 

There are surprisingly few studies of the retention mechanism for open tubular columns but the theory presented for packed columns should be equally applicable. For normal film thicknesses open tubular columns have a large surface area/volume ratio and the contribution of interfacial adsorption to retention should be significant for those solutes that exhibit adsorption tendencies. Interfacial adsorption has been shown to affect the reproducibility of retention for columns prepared with nonpolar phases of different film thicknesses [322-324]. The poor reproducibility of retention index values for columns prepared from polar phases was demonstrated to be c(ue to interfacial... 

Newport In terms of physical limits, we tend to think of DNA, but on the other hand there is RNA degradation and protein turnover. This is how an egg is made. Even though it is only a tetraploid organism, RNA degradation is slowed down significantly, so less DNA is needed. The other physical limitation is the surface area volume relationship. How many receptors or growth factors can be inserted into a membrane ... 

The most common use of protein microarrays is in immunoassays. In particular, antibody-based immunoassays are the main stream of diagnostic assays due to their specificity. The assay usually runs in a multiplexed mode where the antibodies or other capture agents are immobilized and then exposed to a biological sample. There are four immunoassay formats direct binding, sandwich (ELISA), competitive, and displacement. Direct-binding and sandwich assays are the most common. There are some reports on the use of competitive assays and displacement assays, which are usually associated with high surface area/volume systems [72-76],... 

Surface area controlled reactivity, of silver carboxylate, 19 340—342 Surface area measurement, 19 379 Surface area/volume (SAV) ratio in microfluidics, 26 961—962 Surface cartridges, for cartridge filters, 11 369... 

When mixtures of substances are investigated, e.g. in solid state reactions, the mixture should be completely homogeneous and of uniform particle size. Smaller particle size, i.e. higher ratio surface area/volume, are important for such types of reaction ... 

Frank in dogs. The most likely explanation is that the model does not account for chemical reactions of ozone in the mucus and epithelial tissue. Another problem is that the nose is believed to behave more like a scrubbing tower with fresh liquid at each level, inasmuch as the blood supply is not continuous for the entire length of the nose, as assumed in the model. Neglecting the surface area, volume, flow, and thickness of the mucus layer in the nose will probably also give erroneous results for soluble gases with a small diffusion coefficient in mucus and for singlebreath inhalations of a low concentration of any gas. 

Rate-limiting process Order energy Surface area volume... 

Fig. 5. The r2 correlation coefficients for linear models of traditional descriptors as a function of the 32 VSA descriptors. Notes (a) connectivity and kappa shape indices (4) (b) van der Waals surface area, volume, and density ...

The pore size of the membrane could also be controlled independently of the porosity by altering the size of the salt particles (Fig. 5a). Membranes with high surface area/volume ratios were produced and the ratio was dependent on both salt weight fraction and particle size (Fig. 5b). In addition, the crystallinity of PLLA membranes can be tailored to that desired for each application. These characteristics are all desirable properties of a scaffold for organ regeneration. The major disadvantage of this technique is that it can only be used to produce thin wafers or membranes (up to 2 mm in thickness). A three-dimensional scaffold cannot be directly constructed. This problem may be circumvented however, by membrane lamination. 

---