Surface analysis by laser ablation

In conclusion, GD-OE S is a very versatile analytical technique which is still in a state of rapid technical development. In particular, the introduction of rf sources for non-conductive materials has opened up new areas of application. Further development of more advanced techniques, e. g. pulsed glow discharge operation combined with time-gated detection [4.217], is likely to improve the analytical capabilities of GD-OE S in the near future. 

The advantages of LA are now well-known - no sample preparation is needed, conducting and non-conducting samples of arbitrary structure can be analyzed directly, spatial resolution up to a few microns can be obtained, high vacuum conditions are not required, rapid simultaneous multi-element analysis is possible, and it is possible to obtain complete analytical information with a single laser pulse. A brief overview of the potential and limitations of LA will be given in this chapter. 

---

Some solid materials are very intractable to analysis by standard methods and cannot be easily vaporized or dissolved in common solvents. Glass, bone, dried paint, and archaeological samples are common examples. These materials would now be examined by laser ablation, a technique that produces an aerosol of particulate matter. The laser can be used in its defocused mode for surface profiling or in its focused mode for depth profiling. Interestingly, lasers can be used to vaporize even thermally labile materials through use of the matrix-assisted laser desorption ionization (MALDI) method variant. 

In laser ablation, a solid sample is irradiated with a laser pulse that ablates the point of laser-solid contact to produce a plume of ions and neutrals in the vapor space just above the point of laser-solid contact with the sample surface. If this plume is swept into an ionization source or if reactant ions are electrically focused into the ablated sample plume, product ions are formed. These ions can be electrically focused into an IMS for ion mobility analysis. Direct laser ablation followed by ionization from... 

Neff, H. (2003) Analysis of Plumbate pottery surfaces by laser ablation-inductively coupled plasma-mass spectrometry LA-ICP-MS. Journal of Archaeological Science, 30, 21-35. 

Initial results prove the high potential of LA-based hyphenated techniques for depth profiling of coatings and multilayer samples. These techniques can be used as complementary methods to other surface-analysis techniques. Probably the most reasonable application of laser ablation for depth profiling would be the range from a few tens of nanometers to a few tens of microns, a range which is difficult to analyze by other techniques, e. g. SIMS, SNMS,TXRE, GD-OES-MS, etc. The lateral and depth resolution of LA can both be improved by use of femtosecond lasers. 

Laser microprobe MS (LMMS) can be used for direct analysis of normal-phase HPTLC plates [802,837]. Kubis et al. [802] used polyamide TLC plates polyamide does not interfere with compound identification by the mass spectrum, owing to its low-mass fragment-ions (m/z < 150). LMMS is essentially a surface analysis technique, in which the sample is ablated using a Nd-YAG laser. The UV irradiation desorbs and ionises a microvolume of the sample the positive and negative ions can be analysed by using a ToF mass spectrometer. The main characteristics of TLC-LMMS are indicated in Table 7.84 [838],... 

Gonzalez et al. 2008). Laser ablation is a direct sampling technique by which a high energy laser is focused on the surface of a material and atoms, ions, and particles are ejected. The particles, which are chemically representative of the bulk sample, are then transported into an ICPMS for analysis. In LIBS, a luminous, short-lived plasma is created on the sample surface by the focused laser beam and its emission spectra are analyzed to provide both qualitative and quantitative chemical compositional analysis (Cremers... 

Mass spectrometric measurements of ions desorbed/ionized from a surface by a laser beam was first performed in 1963 by Honig and Woolston [151], who utilized a pulsed mby laser with 50 p,s pulse length. Hillenkamp et al. used microscope optics to focus the laser beam diameter to 0.5 p,m [152], allowing for surface analysis with high spatial resolution. In 1978 Posthumus et al. [153] demonstrated that laser desorption /ionization (LDI, also commonly referred to as laser ionization or laser ablation) could produce spectra of nonvolatile compounds with mass > 1 kDa. For a detailed review of the early development of LDI, see Reference 154. There is no principal difference between an LDI source and a MALDI source, which is described in detail in Section 2.1.22 In LDI no particular sample preparation is required (contrary to... 

---