Supercritical fluids critical properties

In general, the properties of supercritical fluids make them interesting media in which to conduct chemical reactions. A supercritical fluid can be defined as a substance or mixture at conditions which exceed the critical temperature (Tc) and critical pressure (Pc). One of the primary advantages of employing a supercritical fluid as the continuous phase lies in the ability to manipulate the solvent strength (dielectric constant) simply by varying the temperature and pressure of the system. Additionally, supercritical fluids have properties which are intermediate between those of a liquid and those of a gas. As an illustration, a supercritical fluid can have liquid-like density and simultaneously possess gas-like viscosity. For more information, the reader is referred to several books which have been published on supercritical fluid science and technology [1-4],... 

Supercritical fluid chromatography (SFC) is a GC method of analysis of compounds in systems where normal GC presents resolution difficulties (Lee and Markides, 1987). A supercritical fluid has properties at a critical temperature intermediate between a liquid and a gas. At and above this critical temperature, a gas cannot be compressed into a liquid, irrespective of the pressure, but it solvates solid matter as if it were a liquid. A supercritical fluid diffuses freely into and out of adsorbent pores with a minimum of resistance. A major advantage of SFC chromatography is its ability to effect separation of oligomers without derivatization. 

For safe and long-term storage, carbon dioxide must be injected more than 800 m below the Earth s surface. At that depth, the gas becomes a supercritical fluid. Such fluids have the gas-like characteristic of low viscosity and the liquidlike characteristic of high density. Supercritical behaviour exists only when temperature and pressure both reach, or exceed, their respective values at the so-called critical point . Every substance has its own critical temperature, above which the gas cannot be liquefied no matter how high the pressure. For carbon dioxide, the critical point lies at 31 °C and 7.4 MPa. Supercritical fluids have properties similar to those of liquid solvents and are employed commercially to extract soluble substances. For example, supercritical carbon dioxide is used to remove caffeine from coffee. 

Supercritical fluids have properties of both gases and liquids, when they are raised above their critical temperature and pressure points. As a solvent, they exhibit a number of special features ... 

Researchers are interested in supercritical fluids because of their unique properties. A supercritical fluid has properties of both liquids and gases—it is in some sense intermediate between the two. Supercritical fluids can act as good solvents, selectively dissolving a number of compounds. For example, supercritical carbon dioxide is used as a solvent to extract caffeine from coffee beans. The caffeine dissolves in the supercritical carbon dioxide, but other substances—such as those responsible for the flavor of coffee—do not. Consequently, the caffeine is removed without substautially altering the coffee s flavor. The supercritical carbon dioxide is easily removed from the mixture by simply lowering the pressure below the critical pressure, at which point the carbon dioxide evaporates, leaving no residue. 

Critical Point Properties for Selected Supercritical Fluids... 

Supercritical Fluid Extraction. Supercritical fluid (SCF) extraction is a process in which elevated pressure and temperature conditions are used to make a substance exceed a critical point. Once above this critical point, the gas (CO2 is commonly used) exhibits unique solvating properties. The advantages of SCF extraction in foods are that there is no solvent residue in the extracted products, the process can be performed at low temperature, oxygen is excluded, and there is minimal protein degradation (49). One area in which SCF extraction of Hpids from meats maybe appHed is in the production of low fat dried meat ingredients for further processed items. Its apphcation in fresh meat is less successful because the fresh meat contains relatively high levels of moisture (50). 

Conventional nitrocellulose lacquer finishing leads to the emission of large quantities of solvents into the atmosphere. An ingeneous approach to reducing VOC emissions is the use of supercritical carbon dioxide as a component of the solvent mixture (172). The critical temperature and pressure of CO2 are 31.3°C and 7.4 MPa (72.9 atm), respectively. Below that temperature and above that pressure, CO2 is a supercritical fluid. It has been found that under these conditions, the solvency properties of CO2 ate similar to aromatic hydrocarbons (see Supercritical fluids). The coating is shipped in a concentrated form, then metered with supercritical CO2 into a proportioning airless spray gun system in such a ratio as to reduce the viscosity to the level needed for proper atomization. VOC emission reductions of 50% or more are projected. 

Supercriticalfluid solvents are those formed by operating a system above the critical conditions of the solvent. SolubiHties of many solutes ia such fluids often is much greater than those found for the same solutes but with the fluid at sub atmospheric conditions. Recently, there has been considerable iaterest ia usiag supercritical fluids as solvents ia the production of certain crystalline materials because of the special properties of the product crystals. Rapid expansion of a supercritical system rapidly reduces the solubiHty of a solute throughout the entire mixture. The resulting high supersaturation produces fine crystals of relatively uniform size. Moreover, the solvent poses no purification problems because it simply becomes a gas as the system conditions are reduced below critical. 

A variety of equations-of-state have been applied to supercritical fluids, ranging from simple cubic equations like the Peng-Robinson equation-of-state to the Statistical Associating Fluid Theoiy. All are able to model nonpolar systems fairly successfully, but most are increasingly chaUenged as the polarity of the components increases. The key is to calculate the solute-fluid molecular interaction parameter from the pure-component properties. Often the standard approach (i.e. corresponding states based on critical properties) is of limited accuracy due to the vastly different critical temperatures of the solutes (if known) and the solvents other properties of the solute... 

Supercritical fluid chromatography (SFC) refers to the use of mobile phases at temperatures and pressures above the critical point (supercritical) or just below (sub-critical). SFC shows several features that can be advantageous for its application to large-scale separations [132-135]. One of the most interesting properties of this technique is the low viscosity of the solvents used that, combined with high diffusion coefficients for solutes, leads to a higher efficiency and a shorter analysis time than in HPLC. 

Above the critical temperature and pressure, a substance is referred to as a supercritical fluid. Such fluids have unusual solvent properties that have led to many practical applications. Supercritical carbon dioxide is used most commonly because it is cheap, nontoxic, and relatively easy to liquefy (critical T = 31°C, P = 73 atm). It was first used more than 20 years ago to extract caffeine from coffee dichloromethane, CH2C12, long used for this purpose, is both a narcotic and a potential carcinogen. Today more than 10s metric tons of decaf coffee are made annually using supercritical C02. It is also used on a large scale to extract nicotine from tobacco and various objectionable impurities from the hops used to make beer. 

Above 30.9 °C, CO2 cannot be liquefied by compression it exists in a supercritical fluid phase (SC-CO2) that behaves like a gas that is denser than liquid CO2. Below 30.9 °C, CO2 can be maintained as a liquid under relatively modest pressure generally SC-CO2 has better solvent properties than CO2 in the sub-critical liquid phase. 

Supercritical fluids (SCFs) are compounds that exist at a temperature and pressure that are above their corresponding critical values [70,71]. They exhibit the properties of both gases and Hquids. With gases, they share the properties of low surface tension, low viscosity, and high diffusivity. Their main Hquid-like feature is the density, which results in enhanced solubility of solutes compared with the solubility of gases. Furthermore, the solubility of solutes can be manipulated by changes in pressure and temperature near the critical point [72]. 

A supercritical fluid exhibits physical-chemical properties intermediate between those of liquids and gases. Mass transfer is rapid with supercritical fluids. Their dynamic viscosities are nearer to those in normal gaseous states. In the vicinity of the critical point the diffusion coefficient is more than 10 times that of a liquid. Carbon dioxide can be compressed readily to form a liquid. Under typical borehole conditions, carbon dioxide is a supercritical fluid. 

SEE is an instrumental approach not unlike PLE except that a supercritical fluid rather than a liquid is used as the extraction solvent. SFE and PLE employ the same procedures for preparing samples and loading extraction vessels, and the same concepts of static and dynamic extractions are also pertinent. SFE typically requires higher pressure than PLE to maintain supercritical conditions and, for this reason, SFE usually requires a restrictor to control better the flow and pressure of the extraction fluid. CO2 is by far the most common solvent used in SFE owing to its relatively low critical point (78 atm and 31 °C), extraction properties, availability, gaseous natural state, and safety. 

---