Stirring methods mechanical

Very recently, a dry-stir method for the mechanical activation of commercial magnesium turnings was reported16. The procedure is also excellently suited for the preparation of allylic and benzylic Grignard reagents (Table 1, method B). 

Not-Shaken-Not-Stirred Method Highly dispersible PANI-NFs ean be reprodueibly prepared from a conventional reaction simply by not mechanically agitating the reaction and carrying it out at an elevated temperature (Figure 2.6) [52]. It was shown that... 

X. H. Qin, B.L. Xiao, and S.M. Dong, et al, SiCf/SiC Composites Reinforced by Randomly Oriented Chopped Fibers Prepared by Semi-Solid Mechanical Stirring Method and Hot Pressing, / Mater. 5c/., 42(10] 3488-3494(2007). 

Actually, the following experimental conditions should be optimized to fabricate the present type weU-defined hybridized NCs, except for selected combination of 7t-conjugated polymer and a noble metal, concentration of metal-salt solution, initial pH control by adding base like ammonia, reaction temperature and time, stirring method, and VIS light intensity [53,54]. Recently, it has become apparent that ultrasonic wave irradiation is much more effective than mechanical stirring [121],... 

Method(B). Add3g. (3ml.)ofbenzonitrileto50ml.of lo-volumes hydrogen peroxide in a beaker, stir mechanically and add i ml. of 10% aqueous sodium hydroxide solution. Warm the stirred mixture at 40° until the oily suspension of the nitrile has been completely replaced by the crystalline benzamide (45-60 minutes). Cool the solution until crystallisation of the benzamide is complete, and then filter at the pump and recrystallise as above. One recrystallisation gives the pure benza-mide, m.p. 129-130° yield of purified material, 2-2-5 S ... 

Cuprous cyanide solution. The most satisfactory method is to dissolve the cuprous cyanide (1 mol) in a solution of technical sodium cyanide (2 5-2-6 mols in 600 ml. of water). If it is desired to avoid the preparation of solid cuprous cyanide, the following procedure may be adopted. Cuprous chloride, prepared from 125 g. of copper sulphate crystals as described under 1 above, is suspended in 200 ml. of water contained in a 1-litre round-bottomed flask, which is fitted with a mechanical stirrer. A solution of 65 g. of technical sodium cyanide (96-98 per cent.) in 100 ml. of water is added and the mixture is stirred. The cuprous chloride passes into solution with considerable evolution of heat. As the cuprous cyanide is usually emplo3 ed in some modification of the diazo reaction, it is usual to cool the resulting solution in ice. 

An alternative method of conducting the preparation consists in treating 100 g. of cycZohexanol with 250 ml. of concentrated hydrochloric acid, refluxing slowly whilst a stream of hydrogen chloride gas is passed into the mechanically stirred... 

In general, benzoylation of aromatic amines finds less application than acetylation in preparative work, but the process is often employed for the identification and characterisation of aromatic amines (and also of hydroxy compounds). Benzoyl chloride (Section IV, 185) is the reagent commonly used. This reagent is so slowly hydrolysed by water that benzoylation can be carried out in an aqueous medium. In the Schotten-Baumann method of benzoylation the amino compound or its salt is dissolved or suspended in a slight excess of 8-15 per cent, sodium hydroxide solution, a small excess (about 10-15 per cent, more than the theoretical quantity) of benzoyl chloride is then added and the mixture vigorously shaken in a stoppered vessel (or else the mixture is stirred mechanically). Benzoylation proceeds smoothly and the sparingly soluble benzoyl derivative usually separates as a solid. The sodium hydroxide hydrolyses the excess of benzoyl chloride, yielding sodium benzoate and sodium chloride, which remain in solution ... 

The following alternative method of preparation is recommended. Dissolve 50 g. of purified 2 4-dinitrochlorobenzene (1) in 100 ml. of triethylene glycol (gentle warming nia be necessary alternatively, 125 ml. of warm diethylene glycol may be used) in a 600 ml. beaker and cool, with mechanical stirring, in an ice bath to 15-18°. Place 15 ml. of commercial 60-65 per cent, hydrazine solution in a small separatory funnel supported over the beaker. Add the hydrazine solution to the stirred solution in the beaker at such a rate that the temperature is maintained between 15° and 20° (20-30 minutes). When... 

Method 2. Equip a 1 htre thre necked flask with a double surface reflux condenser, a mechanical stirrer and a separatory funnel, and place 12 -2 g. of dry magnesium turnings, a crystal of iodine, 50 ml. of sodium-dried ether and 7-5 g. (5 ml.) of a-bromonaphthalene (Section IV,20) in the flask. If the reaction does not start immediately, reflux gently on a water bath until it does remove the water bath. Stir the mixture, and add a solution of 96 g. (65 ml.) of a-bromonaphthalene in 250 ml. of anhydrous ether from the separatory funnel at such a rate that the reaction is vmder control (1 -5-2 hours). Place a water bath under the flask and continue the stirring and refluxing for a further 30 minutes. The Grignard reagent collects as a heavy oil in the bottom of the flask ... 

Method 1. Equip a 1 litre three-necked flask (or bolt-head flask) with a separatory funnel, a mechanical stirrer (Fig. II, 7, 10), a thermometer (with bulb within 2 cm. of the bottom) and an exit tube leading to a gas absorption device (Fig. II, 8, 1, c). Place 700 g. (400 ml.) of chloro-sulphonic acid in the flask and add slowly, with stirring, 156 g. (176 ml.) of pure benzene (1) maintain the temperature between 20° and 25° by immersing the flask in cold water, if necessary. After the addition is complete (about 2 5 hours), stir the mixture for 1 hour, and then pour it on to 1500 g. of crushed ice. Add 200 ml. of carbon tetrachloride, stir, and separate the oil as soon as possible (otherwise appreciable hydrolysis occurs) extract the aqueous layer with 100 ml. of carbon tetrachloride. Wash the combined extracts with dilute sodium carbonate solution, distil off most of the solvent under atmospheric pressure (2), and distil the residue under reduced pressure. Collect the benzenesulphonyl chloride at 118-120°/15 mm. it solidifies to a colourless sohd, m.p. 13-14°, when cooled in ice. The yield is 270 g. A small amount (10-20 g.) of diphen3 lsulphone, b.p. 225°/10 mm., m.p. 128°, remains in the flask. 

Method A. Cool a solution of the nitrate-free dichloride, prepared from or equivalent to 5 0 g. of palladium or platinum, in 50 ml. of water and 5 ml. of concentrated hydrochloric acid in a freezing mixture, and treat it with 50 ml. of formahn (40 per cent, formaldehyde) and 11 g. of the carrier (charcoal or asbestos). Stir the mixture mechanically and add a solution of 50 g. of potassium hydroxide in 50 ml. of water, keeping the temperature below 5°. When the addition is complete, raise the temperature to 60° for 15 minutes. Wash the catalyst thoroughly by decantation with water and finally with dilute acetic acid, collect on a suction filter, and wash with hot water until free from chloride or alkali. Dry at 100° and store in a desiccator. 

Meihylamine hydrochloride method. Place 100 g. of 24 per cent, methyl-amine solution (6) in a tared 500 ml. flask and add concentrated hydrochloric acid (about 78 ml.) until the solution is acid to methyl red. Add water to bring the total weight to 250 g., then introduce lSO g. of urea, and boil the solution gently under reflux for two and three-quarter hours, and then vigorously for 15 minutes. Cool the solution to room temperature, dissolve 55 g. of 95 per cent, sodium nitrite in it, and cool to 0°. Prepare a mixture of 300 g. of crushed ice and 50 g. of concentrated sulphuric acid in a 1500 ml. beaker surrounded by a bath of ice and salt, and add the cold methylurea - nitrite solution slowly and with mechanical stirring and at such a rate (about 1 hour) that the temperature does not rise above 0°. It is recommended that the stem of the funnel containii the methylurea - nitrite solution dip below the surface of the acid solution. The nitrosomethylurea rises to the surface as a crystalline foamy precipitate. Filter at once at the pump, and drain well. Stir the crystals into a paste with about 50 ml. of cold water, suck as dry as possible, and dry in a vacuum desiccator to constant weight. The yield is 55 g. (5). 

Convection occurs when a mechanical means is used to carry reactants toward the electrode and to remove products from the electrode. The most common means of convection is to stir the solution using a stir bar. Other methods include rotating the electrode and incorporating the electrode into a flow cell. 

The procedure which had originally been used by Lehn et al. involved slow addition (over a period of ca. 8 h) of ca. 0.1 M solutions of diamine and diacyl halide in benzene. Dye et al. found that the reactions could be conducted more rapidly as long as stirring was kept efficient. This observation suggested the use of a mixing chamber of the type normally used for stopped-flow kinetic studies. Utilizing this type of set-up, the latter authors were able to obtain a 70% yield for 1, slightly inferior to the yield reported by Lehn, but a similar yield of 3 which is better than that previously ob-tained. Note that the chemical features of this synthetic method are essentially identical to the approach shown in Eq. (8.1) and differ primarily in the mechanics. 

Hydroxy-B-homo-5a-cholestan-7-one acetate (54b) A solution of 3/3-hydroxy-5a-cholestan-7-one acetate (51b 5 g mp 146-148°) in dioxane-ethanol (100 ml, 1 1) is placed in a 250 ml three-necked flask equipped with a mechanical stirrer and thermometer and is cooled to 0° (iee-salt bath). Powdered potassium cyanide (7.3 g) is added portionwise with stirring. Acetic acid (8 ml) is then added dropwise with constant stirring over 30 min. The resultant mixture is stirred for 1 hr at 0° C and for an additional 2 hr at room temperature. It is then poured into ice water (200 g ice, 100 ml water) and after standing for 1 hr the precipitate is collected by filtration. The product is dissolved in ether (100 ml), the ether solution is washed with 5% sodium bicarbonate, water and dried over anhydrous sodium sulfate. The filtrate is evaporated at reduced pressure and the solid residue (5.1 g) is crystallized from ethyl acetate (30 ml) to yield 2.8 g of cyanohydrin (52b) mp 160-164° repeated crystallization from the same solvent gives a product mp 164-167°. An alternative method of isolation of the cyanohydrin is used when 100 g or larger quantities are worked up. The reaction mixture is poured directly into a mixture of ice water and sodium bicarbonate, the precipitate (mp 155-156°) is washed well with water, dried and used directly for the next step. 

When the physical modification method is used, PS is modified by mechanical stirring with various synthetic rubbers such as polybutadiene, polybutadiene styrene, polyisopropene, polychloropropene, polybutadiene styrene-acrylonitrile copolymers. In the chemical modification, PS is modified with polyfunctional modificators in the presence of cationic catalysis. 

---