Steam distillation products

It is not practical to dry the steam-distilled product in the air, because a-hydrindone has such a high vapor pressure that the loss is appreciable. Drying can be accomplished in a vacuum desiccator, but this takes several days. The distillation... 

Chamazulene] Steam distillation product of 5-LOX (2) [inhibits LTB4... 

Methyl benzyl ketone cyanohydrin and ethyl mercaptan in anhydrous benzene or benzene-ether ice-cooled, satd. with HCl, kept 15 days in a refrigerator, the resulting crude thioimidoester hydrochloride treated with water, and steam-distilled product. Y 80.2%. F. e. s. W.E. Elias, Can. J. Chem. 48, 3662 (1970). 

If the organic compound which is being steam-distilled is freely soluble in water, an aqueous solution will ultimately collect in the receiver F, and the compound must then be isolated by ether extraction, etc. Alternatively, a water-insoluble compound, if liquid, will form a separate layer in F, or if solid, will probably ciystallise in the aqueous distillate. When steam-distilling a solid product, it is sometimes found that the distilled material crystallises in E, and may tend to choke up the condenser, in such cases, the water should be run out of the condenser for a few minutes until the solid material has melted and been carried by the steam down into the receiver. 

HjSnCl, with which the aniline forms a salt, aniline chlorostannate (C4HjNH )i,H SnCl4, similar in type to aniline chloroplatinate (p. 448). The crude product is therefore made strongly alkaline with sodium hydroxide, which liberates the base with the formation of sodium stannate, and the aniline can (C4H NH,),H,SnCl, + SNaOH = 2C,H,NH, + Na.SnO, +6NaCl + sHjO then be removed by steam-distillation. 

Prepare a mixture of 30 ml, of aniline, 8 g. of o-chloro-benzoic acid, 8 g. of anhydrous potassium carbonate and 0 4 g. of copper oxide in a 500 ml. round-bottomed flask fitted with an air-condenser, and then boil the mixture under reflux for 1 5 hours the mixture tends to foam during the earlier part of the heating owing to the evolution of carbon dioxide, and hence the large flask is used. When the heating has been completed, fit the flask with a steam-distillation head, and stcam-distil the crude product until all the excess of aniline has been removed. The residual solution now contains the potassium. V-phenylanthrani-late add ca. 2 g. of animal charcoal to this solution, boil for about 5 minutes, and filter hot. Add dilute hydrochloric acid (1 1 by volume) to the filtrate until no further precipitation occurs, and then cool in ice-water with stirring. Filter otT the. V-phcnylanthranilic acid at the pump, wash with water, drain and dry. Yield, 9-9 5 g. I he acid may be recrystallised from aqueous ethanol, or methylated spirit, with addition of charcoal if necessary, and is obtained as colourless crystals, m.p. 185-186°. 

Fit securely to the lower end of the condenser (as a receiver) a Buchner flask, the side-tube carrying a piece of rubber tubing which falls well below the level of the bench. Steam-distil the ethereal mixture for about 30 minutes discard the distillate, which contains the ether, possibly a trace of unchanged ethyl benzoate, and also any biphenyl, CeHs CgHs, which has been formed. The residue in the flask contains the triphenyl carbinol, which solidifies when the liquid is cooled. Filter this residual product at the pump, wash the triphenyl-carbinol thoroughly with water, drain, and then dry by pressing between several layers of thick drying-paper. Yield of crude dry product, 8 g. The triphenyl-carbinol can be recrystallised from methylated spirit (yield, 6 g.), or, if quite dry, from benzene, and so obtained as colourless crystals, m.p. 162. ... 

Steam-distil the ethereal solution and discard the distillate. The residue in the flask is triphenyl-carbinol and solidifies on cooling. Filter at the pump, wash with water, drain and dry. Yield of crude product 0 6 g. Recrystallise when dry from benzene to obtain colourless crystals m.p. 162°. 

When the crude reaction product is made alkaline and steam-distilled, a mixture of quinoline and some unchanged aniline passes over. Pure quinoline can be isolated from this mixture by one of the following methods ... 

The mixed bases are boiled with an acetic acid-acetic anhydride mixture to convert the aniline into acetanilide. The product is poured into water, when the acetanilide crystallises out while the quinoline remains in solution as quinoline acetate. The acetanilide is filtered off, and the filtrate made alkaline and steam-distilled. 

The reaction is carried out in a 2-litre long-necked round-bottomed flask, to which is fitted an efficient reflux water-condenser, capable of condensing a sudden rush of vapour without choking. For this purpose, a long bulb-condenser, similar to that shown in Fig. 3(A) (p. 9) is best, but the inner tube must be of wide bore (at least 12 mm.). Alternatively, an air-condenser of wide bore may be used, an.d a short double-surface water-condenser fitted to its top. A steam-distillation fitting for the flask should also be prepared in advance, so that the crude product can subsequently be steam-distilled directly from the flask. The glj cerol used in the preparation must be anhydrous, and should therefore be dehydrated by the method described on p. 113. 

Equation (3) indicates the great value of steam distillation, since the smaller the product the laiger Ls the value of w. Water has a... 

In practice superheated steam is generally employed for substances with a low vapour pressure (< 5-1 mm.) at 100°. Thus in the recovery of the products of nitration or aromatic compounds, the ortho derivative e.g., o-nitrophenol) can be removed by ordinary steam distillation the... 

Nitrobenzene. Nitrobenzene, of analytical reagent quality, is satisfactory for most purposes. The technical product may contain dinitrobenzene and other impurities, whilst the recovered solvent may be contaminated with aniline. Most of the impurities may be removed by steam distillation after the addition of dilute sulphuric acid the nitrobenzene in the distillate is separated, dried with calcium chloride and distilled. The pure substance has b.p. 210°/760 mm. and m.p. 5 -7°. 

Di-n-amyl ether. Use 50 g. (61 5 ml.) of n-amyl alcohol (b.p. 136-137°) and 7 g. (4 ml.) of concentrated sulphuric acid. The calculated volume of water (5 ml.) is collected when the temperature inside the flask rises to 157° (after 90 minutes). Steam distil the reaction mixture, separate the upper layer of the distillate and dry it with anhydrous potassium carbonate. Distil from a 50 ml. Claisen flask and collect the fractions of boiling point (i) 145-175° (13 g.), (ii) 175-185° (8 g.) and (iii) 185-190° (largely 185-185-5°) (13 g.). Combine fractions (i) and (u), reflux for 1 hour in a small flask with 3 g. of sodium, and distil from the sodium amyloxide and excess of sodium this yields 9 5 g. of fairly pure n-amyl ether (iv). The total yield is therefore 22 - 5 g. A perfectly pure product, b.p. 184 185°, is obtained by further distillation from a Little sodium. 

About 0-1 per cent, of hydroquinone should be added as a stabiliser since n-hexaldehyde exhibits a great tendency to polymerise. To obtain perfectly pure n-/iexaldehyde, treat the 21 g. of the product with a solution of 42 g. of sodium bisulphite in 125 ml. of water and shake much bisulphite derivative will separate. Steam distil the suspension of the bisulphite compound until about 50 ml. of distillate have been collected this will remove any non-aldehydic impurities together with a little aldehyde. Cool the residual aldehyde bisulphite solution to 40-50 , and add slowly a solution of 32 g. of sodium bicarbonate in 80 ml. of water, and remove the free aldehyde by steam distillation. Separate the upper layer of n-hexaldehyde, wash it with a little water, dry with anhydrous magnesium sulphate and distil the pure aldehyde passes over at 128-128-5°. 

If the presence of unreduced nitrobenzene is suspected (odour and/or high b.p. residue), treat all the product with excess of dilute hydrochloric acid and remove the nitrobenzene either by steam distillation or by ether extraction render the residue alkaline with sodium hydroxide solution and isolate the aniline os before. 

The ester and catalj st are usually employed in equimoleciilar amounts. With R =CjHs (phenyl propionate), the products are o- and p-propiophenol with R = CH3 (phenyl acetate), o- and p-hydroxyacetophenone are formed. The nature of the product is influenced by the structure of the ester, by the temperature, the solvent and the amount of aluminium chloride used generally, low reaction temperatures favour the formation of p-hydroxy ketones. It is usually possible to separate the two hydroxy ketones by fractional distillation under diminished pressure through an efficient fractionating column or by steam distillation the ortho compounds, being chelated, are more volatile in steam It may be mentioned that Clemmensen reduction (compare Section IV,6) of the hj droxy ketones affords an excellent route to the substituted phenols. 

---