Specific gravity calculated

This correlation was tested with gases with nonhydrocarbon contents up to 43 percent. Reservoir gas specific gravities calculated with Equation 7-9, using Equations B-31 and B-32 for VEQ and AGP, were within one percent of laboratory measurements when nonhydrocarbon content was below five percent and within six percent of laboratory measurements when nonhydrocarbon content was between five percent... 

The results are summarized in the table below. Using a volume basis of 1 of sample, the masses of the pseudocomponents are also calculated from their specific gravities. The overall specific gravity calculated from the component gravities is 0.801, in close agreement with the measured value hence no normalization of the component specific gravities is necessary. 

The authors wish to thank Mr, A. Bissonnet and R. Ripon for the adaptation of the logarithmic converter and the construction of the electronic device for the specific gravity calculation. 

It is common that a mixture of hydrocarbons whose boiling points are far enough apart petroleum cut) is characterized by a distillation curve and an average standard specific gravity. It is then necessary to calculate the standard specific gravity of each fraction composing the cut by using the relation below [4.8] ... 

For petroleum fractions, the values should be calculated starting with the standard specific gravity accor( ing to the relation ... 

Maxwell and Bonnel (1955) proposed a method to calculate the vapor pressure of pure hydrocarbons or petroleum fractions whose normal boiling point and specific gravity are known. It is iterative if the boiling point is greater than 366.5 K ... 

Calculation of the atmospheric TBP is rapid if it can be assumed that this distillation is ideal (which is not always the case in reality). It is only necessary to arrange the components in order of increasing boiling points and to accumulate the volumes determined by using the standard specific gravity. 

It is possible to calculate the properties of wider cuts given the characteristics of the smaller fractions when these properties are additive in volume, weight or moles. Only the specific gravity, vapor pressure, sulfur content, and aromatics content give this advantage. All others, such as viscosity, flash point, pour point, need to be measured. In this case it is preferable to proceed with a TBP distillation of the wider cuts that correspond with those in an actual refinery whose properties have been measured. 

Density is the most commonly measured property of a gas, and is obtained experimentally by measuring the specific gravity of the gas (density of the gas relative to air = 1). As pressure increases, so does gas density, but the relationship is non-linear since the dimensionless gas compressibility (z-factor) also varies with pressure. The gas density (pg) can be calculated at any pressure and temperature using the real gas law ... 

Iridium is not attacked by any of the acids nor by aqua regia, but is attacked by molten salts, such as NaCl and NaCN. The specific gravity of iridium is only very slightly lower than osmium, which is generally credited as the heaviest known element. Calculations of the densities of iridium and osmium from the space lattices give values of 22.65 and 22.61 g/cm 3, respectively. These values may be more reliable than actual physical measurements. At present, therefore, we know that either iridium or osmium is the densest known element, but the data do not yet allow selection between the two. 

Calculated equivalent for avaerage specific gravity gasoline (0.737 specific gravity at 16°C, NIPER Gasoline Report). Calculated equivalent depends on the specific gravity of the gasoline. 

A typical slag (specific gravity 3.6) contains complex siUcates of iron, calcium, 2iac, magnesium, and aluminum oxides. The quantity of fluxes (compounds added to lower the melting poiat) added depends on the feed composition, and is calculated to ensure a fluid slag at the operating temperature. 

Sulfuric Acid. Sulfuric acid is a dense, colorless Hquid at room temperature, having specific gravity as shown in Figure 3 (50). Historically, the concentration of sulfuric acid has been reported as specific gravity (sp gr) in degrees Baumn. In the United States, the Baumn scale is calculated by the following formula ... 

When criticals cannot he estimated with reasonable accuracy, the method of Maxwell and BonnelP is recommended. The normal boiling point and the specific gravity at 60 F (15.5 C) are required inputs. According to what vapor pressure range is expected, the vapor pressure is calculated from Eqs. (2-34), (2-35), or (2-36). If the wrong range is selected, the procedure will need to be repeated. 

The specific gravity, SG, is the ratio of the density of a given gas to the density of dry air at the same temperature and pressure. It can be calculated from the ratio of molecular weights if the given gas is a perfect gas. 

The following analysis enables one to calculate the diameter of a pipeline transporting any compressible fluid. The required inputs are volumetric flow rate, the specific gravity of the gas relative to air, flow conditions, compressibility factor Z where Z is defined by nZRT = PV, the pressure at the point of origin and the destination, the pipe length, and pipe constants such as effective roughness. The working equations have been obtained from the literature. Since the friction factor... 

To 10 c.c. of the oil (otto of rose or rose-geranium oil) 10 c.c. of formic acid 100 per cent, (specific gravity 1 22) is added, and the mixture gently boiled under a reflux condenser for one hour. The mixture is cooled, 100 c.c. of water added, and the whole transferred to a separator. The aqueous layer is rejected, and the oil washed with successive quantities of water as in the acetylation process. The formylated oil is dried with anhydrous sodium sulphate, and about 2 grams neutralised and saponified with alcoholic potash in the usual manner. The percentage of citronellol is then calculated from the following formula —... 

---