Solvents dimethyl formamide

Materials. Reagent grade solvents, dimethyl formamide (DMF), dimethyl acetamide (DMAC), dimethyl sulfoxide (DMSO) and methanol were purchased from Baker, stored over molecular sieves once opened, and used without further purification. Aminoethane thiosulfuric acid (AETSA) purchased from Kodak, and Taurine, purchased from Alfa were purified by recrystallization. Each was thrice recrystallized from hot, deionized water. The crystalline precipitate was dried (48 hours at 40 °C) in-vacuo and subsequently stored in a desiccator. Benzophenone (BP) was purchased from Aldrich Chemical Company. QUANTACURE BTC (BTC), (4-benzolybenzyl) trimethylammonium chloride, was used as supplied by Aceto, Inc., Flushing, New York. Phenyl glycidyl ether (PGE) was purchased from MCB, distilled in-vacuo. and stored at -15 °C. Epon 828 was used as supplied bv Shell Chemical Company. The epoxy equivalent weight (EEW) for Epon 828 determined by an appropriate titration, was found to be 187.7. 

It is remarkable that thermal decomposition in polar solvents (dimethyl formamide, tetrahydrofuran) gives pentyl cyanide whereas in a nonpolar solvent (decane, 150°) pentyl cyanide is formed together with pentyl isothiocyanate in a 4 1 molar ratio. The same ratio is obtained on injecting 5-pentylthiatriazole into glass wool heated at 350° in an evacuated flask. 

Solvents dimethyl formamide, dimethyl acdimide, n-methyl pyrrolidone, dimethyl sulfoxide, etc. 

Formamide is reported to be a minor metabolite from demethylation of the solvent dimethyl formamide. The molecule is relatively difficult to metabolize with the amide group hydrolyzed to a slight extent by liver extracts at pH 7.4. The dog, cat, and rat excrete a large proportion of an oral dose of formamide unchanged in the urine. 

Studies of X-ray diffraction patterns, specific volume, and mechanical properties of PBLG films led us to intuit that some of these solid films cast from certain solvents such as chloroform and methylene chloride retained the local structure of the liquid crystalline phase. On the other hand, conventionally crystalline films of PBLG were obtained from the solvent dimethyl formamide. ... 

Camarasa IG (1987) Contact dermatitis from dimethylformamide. Contact Dermatitis 16 234 Cox NH, Mustchin CP (1991) Prolonged spontaneous and alcohol-induced flushing due to the solvent dimethyl formamide. Contact Dermatitis 24 69-70... 

Price et a/. have reported C Ti and NOE measurements on narrow fractions of poly(y-benzyl-L-glutamate) in the helix-supporting solvent dimethyl formamide. The strong molecular weight dependence of Tx and was satisfactorily interpreted on the basis of anisotropic rotational diffusion of a rigid helix. 

Dimeihylamine, C2H7N, (CH3)2NH. Colourless, inflammable liquid with an ammoniacal odour, mp -96" C, b.p. 7°C. Occurs naturally in herring brine. Prepared in the laboratory by treating nitrosodimetbyl-aniline with a hot solution of sodium hydroxide. Dimethylamine is largely used in the manufacture of other chemicals. These include the solvents dimethylacetamide and dimethyl-formamide, the rocket propellant unsym-metrical dimethylhydrazine, surface-active agents, herbicides, fungicides and rubber accelerators. 

HC0N(CH3)2, also possess exceptional solvent properties. The alkyl-glycols, dioxan and dimethyl-formamide should be used with caution, however, as their hot vapours are poisonous. 

Poly(7-benzyl-L-glutamate) is known to possess a helical structure in certain solvents. As part of an investigationf of this molecule, a fractionated sample was examined in chloroform (CHCI3) and chloroform saturated ( 0.5%) with dimethyl formamide (DMF). The following results were obtained ... 

In the examples, a nitro group is substituted for a hydrogen atom, and water is a by-product. Nitro groups may, however, be substituted for other atoms or groups of atoms. In Victor Meyer reactions which use silver nitrite, the nitro group replaces a hahde atom, eg, I or Br. In a modification of this method, sodium nitrite dissolved in dimethyl formamide or other suitable solvent is used instead of silver nitrite (1). Nitro compounds can also be produced by addition reactions, eg, the reaction of nitric acid or nitrogen dioxide with unsaturated compounds such as olefins or acetylenes. 

The physical properties of finish removers vary considerably due to the diverse uses and requirements of the removers. Finish removers can be grouped by the principal ingredient of the formula, method of appHcation, method of removal, chemical base, viscosity, or hazardous classification. Except for method of apphcation, a paint remover formulation usually has one aspect of each group, by which it can be used for one or more appHcations. A Hst of the most common organic solvents used in finish removers has been compiled (3). Many are mentioned throughout this article others include ethyl lactate [97-64-3] propylene carbonate [108-32-7] furfural alcohol [98-01-1/, dimethyl formamide [68-12-2] tetrahydrofuran [109-99-9] methyl amyl ketone [110-43-0] dipropylene glycol methyl ether [34590-94-8] and Exxate 600, a trade name of Exxon Chemicals. 

Organic salts (e.g. trimethylammonium benzoate) are usually purified by recrystallisation from polar solvents (e.g. water, ethanol or dimethyl formamide). If the salt is too soluble in a polar solvent, its concentrated solution should be treated dropwise with a miscible nonpolar, or less polar, solvent (see Table 8, Chapter 1) until crystallisation begins. 

The commercial polymers are generally resistant to aqueous acids and alkalis although they are attacked by concentrated sulphuric acid. As might be expected of a highly polar polymer it is not dissolved by aliphatic hydrocarbons but solvents include dimethyl formamide and dimethyl acetamide. 

One approach is to uses solvent extraction with dimethyl formamide (DMF) to remove Cj acetylene and a C, acetylene-propadiene mixture from their steam cracked ethylene and propylene streams. The simple acetylene is sold as welding gas, and the C, stream is sold as starting material for chemical synthesis. 

The importance of the solvent, in many cases an excess of the quatemizing reagent, in the formation of heterocyclic salts was recognized early. The function of dielectric constants and other more detailed influences on quatemization are dealt with in Section VI, but a consideration of the subject from a preparative standpoint is presented here. Methanol and ethanol are used frequently as solvents, and acetone,chloroform, acetonitrile, nitrobenzene, and dimethyl-formamide have been used successfully. The last two solvents were among those considered by Coleman and Fuoss in their search for a suitable solvent for kinetic experiments both solvents gave rise to side reactions when used for the reaction of pyridine with i-butyl bromide. Their observation with nitrobenzene is unexpected, and no other workers have reported difficulties. However, tetramethylene sulfone, 2,4-dimethylsulfolane, ethylene and propylene carbonates, and salicylaldehyde were satisfactory, giving relatively rapid reactions and clean products. Ethylene dichloride, used quite frequently for Friedel-Crafts reactions, would be expected to be a useful solvent but has only recently been used for quatemization reactions. ... 

Polar aprotic solvent (Section 11.3) A polar solvent that can t function as a hydrogen ion donor. Polar aprotic solvents such as dimethyl sulfoxide (DMSO) and dimethyl-formamide (DMF) are particularly useful in Sn2 reactions because of their ability to solvate cations. 

Trimethylamine oxide is normally available as a hydrate, and for the present preparation it is necessary to convert it to its anhydrous form. A convenient way of doing this is as follows. A solution of 45.0 g. of trimethylamine oxide dihydrate (supplied by Beacon Chemicals) is dissolved in 300 ml. of warm dimethyl-formamide and placed in a three-necked flask set up for distillation. At atmospheric pressure the flask is heated and solvent distilled off until the boiling point reaches 152-153°. Then the pressure is reduced using a water aspirator, and the remainder of the solvent is distilled. At the end of the distillation the temperature of the bath is slowly raised to 120°. The residual anhydrous trimethylamine oxide (30 g.) can be dissolved in 100 ml. of chloroform and may remain in the same flask for use in the present preparation. 

---