Solvent extraction mixer-settler

Gigas, B. and Giralico, M. 2002. Advanced methods for designing today s optimum solvent extraction mixer settler unit. In Proceedings international solvent extraction conference, eds. K. C. Sole, P. M. Cole, J. S. Preston, and D. J. Robinson, vol. 2, 1388-1395. Johannesburg South African Institute of Mining and Metallurgy. 

Low shear process will produce larger liquid droplets (>30 microns), and heavy/light liquids can be separated using gravity settling method. Examples of low shear process are solvent extraction, mixer settlers, steam stripping, washing process, and counter-current tower. Coalescer pad can be used to speed up the liquid/liquid separation and reduce the separator size. 

The previous chapters have demonstrated that liquid-liquid extraction is a mass transfer unit operation involving two liquid phases, the raffinate and the extract phase, which have very small mutual solubihty. Let us assume that the raffinate phase is wastewater from a coke plant polluted with phenol. To separate the phenol from the water, there must be close contact with the extract phase, toluene in this case. Water and toluene are not mutually soluble, but toluene is a better solvent for phenol and can extract it from water. Thus, toluene and phenol together are the extract phase. If the solvent reacts with the extracted substance during the extraction, the whole process is called reactive extraction. The reaction is usually used to alter the properties of inorganic cations and anions so they can be extracted from an aqueous solution into the nonpolar organic phase. The mechanisms for these reactions involve ion pah-formation, solvation of an ionic compound, or formation of covalent metal-extractant complexes (see Chapters 3 and 4). Often formation of these new species is a slow process and, in many cases, it is not possible to use columns for this type of extraction mixer-settlers are used instead (Chapter 8). 

In addition to collection of comprehensive distribution data, Schulz s investigations embraced ways of purifying commercial-grade DHDECMP, alpha radiolysis of DHDECMP-CCI4 solvents, and mixer-settler flowsheet tests with both synthetic and actual CAW solutions. Collectively, results of this research clearly demonstrated the many advantages of substituting DHDECMP for DBBP. Shutdown of PRF Am(III) extraction operation in 1976 prevented follow-on plant tests of the DHDECMP flowsheet. 

The development of the novel Davy-McKee combined mixer—settler (CMS) has been described (121). It consists of a single vessel (Fig. 13d) in which three 2ones coexist under operating conditions. A detailed description of units used for uranium recovery has been reported (122), and the units have also been studied at the laboratory scale (123). AppHcation of the Davy combined mixer electrostatically assisted settler (CMAS) to copper stripping from an organic solvent extraction solution has been reported (124). 

In addition, solvent extraction is appHed to the processing of other metals for the nuclear industry and to the reprocessing of spent fuels (see Nuclearreactors). It is commercially used for the cobalt—nickel separation prior to electrowinning in chloride electrolyte. Both extraction columns and mixer-settlers are in use. 

Modem commercial wet-acid purification processes (see Fig. 4) are based on solvents such as C to Cg alcohols, ethers, ketones, amines, and phosphate esters (10—12). Organic-phase extraction of phosphoric acid is accompHshed in one or more extraction columns or, less frequently, in a series of countercurrent mixer—settlers. Generally, 60—75% of the feed acid P2 s content is extracted into the organic phase as H PO. The residual phosphoric acid phase (raffinate), containing 25—40% of the original P2O5 value, is typically used for fertilizer manufacture such as triple superphosphate. For this reason, wet-acid purification units are almost always located within or next to fertilizer complexes. 

For solvent extraction of pentavalent vanadium as a decavanadate anion, the leach solution is acidified to ca pH 3 by addition of sulfuric acid. Vanadium is extracted in about four countercurrent mixer—settler stages by a 3—5 wt % solution of a tertiary alkyl amine in kerosene. The organic solvent is stripped by a soda-ash or ammonium hydroxide solution, and addition of ammoniacal salts to the rich vanadium strip Hquor yields ammonium metavanadate. A small part of the metavanadate is marketed in that form and some is decomposed at a carefully controlled low temperature to make air-dried or fine granular pentoxide, but most is converted to fused pentoxide by thermal decomposition at ca 450°C, melting at 900°C, then chilling and flaking. 

For solvent extraction of a tetravalent vanadium oxyvanadium cation, the leach solution is acidified to ca pH 1.6—2.0 by addition of sulfuric acid, and the redox potential is adjusted to —250 mV by heating and reaction with iron powder. Vanadium is extracted from the blue solution in ca six countercurrent mixer—settler stages by a kerosene solution of 5—6 wt % di-2-ethyIhexyl phosphoric acid (EHPA) and 3 wt % tributyl phosphate (TBP). The organic solvent is stripped by a 15 wt % sulfuric acid solution. The rich strip Hquor containing ca 50—65 g V20 /L is oxidized batchwise initially at pH 0.3 by addition of sodium chlorate then it is heated to 70°C and agitated during the addition of NH to raise the pH to 0.6. Vanadium pentoxide of 98—99% grade precipitates, is removed by filtration, and then is fused and flaked. 

For vanadium solvent extraction, Hon powder can be added to reduce pentavalent vanadium to quadrivalent and trivalent Hon to divalent at a redox potential of —150 mV. The pH is adjusted to 2 by addition of NH, and an oxyvanadium cation is extracted in four countercurrent stages of mixer—settlers by a diesel oil solution of EHPA. Vanadium is stripped from the organic solvent with a 15 wt % sulfuric acid solution in four countercurrent stages. Addition of NH, steam, and sodium chlorate to the strip Hquor results in the precipitation of vanadium oxides, which are filtered, dried, fused, and flaked (22). Vanadium can also be extracted from oxidized uranium raffinate by solvent extraction with a tertiary amine, and ammonium metavanadate is produced from the soda-ash strip Hquor. Fused and flaked pentoxide is made from the ammonium metavanadate (23). 

Liquid-Liquid Extraction The actual configuration of mixers in multistage mixer-settlers and/or multistage columns is summarized in Section 15. A general handbook on this subject is Handbook of Solvent Extraction by Lowe, Beard, and Hanson. This handbook gives a comprehensive review of this entire operation as well. 

Extraction (sometimes called leaching) encompasses liquid-liquid as well as liquid-solid systems. Liquid-liquid extraction involves the transfer of solutes from one liquid phase into another liquid solvent it is normally conducted in mixer settlers, plate and agitated-tower contacting equipment, or packed or spray towers. Liquid-solid extraction, in which a liquid solvent is passed over a solid phase to remove some solute, is carried out in fixed-bed, moving-bed, or agitated-solid columns. 

The actual stage can be a mixing vessel, as in a mixer-settler used for solvent extraction applications, or a plate of a distillation or gas absorption column. In order to allow for non-ideal conditions in which the compositions of the two exit streams do not achieve full equilibrium, an actual number of stages can be related to the number of theoretical stages, via the use of a stage-efficiency factor. 

Solvent extraction carried out in conventional contactors like mixer-settlers and columns has certain limitations, including (a) controlling optimum dispersion and coalescence, (b) purifying both phases to ensure that stable emulsions are avoided (c) temperature control within a narrow band (d) high entrained solvent losses and related environmental and process economic effects and (e) large equipment dimensions and energy requirements when the density differential or selectivity is low. 

The initial bench-scale experimental investigations into solvent extraction processes are conducted with small apparatus, such as separating funnels. Following the successful completion of these tests, when the best reagent and other conditions for the system have been established, small-scale continuous operations are run, such as in a small mixer-settler unit. The data so obtained are used to determine scale-up factors for pilot plant or plant design and operation (see Chapters 7 and 8). 

Commercially available equipment for small-scale continuous test work on a solvent extraction process is limited. Generally, a series of small mixer-settlers... 

Because of the diversity of contacting equipment available, it is unlikely that all these contactors will be available in any one laboratory or pilot plant. Consequently, unless test work is carried out on similar contactors, the system may not be optimized. Since mixer-settlers are the easiest to construct, are simple to operate, and require little room and low-flow rates, these contactors are, in many cases, the only ones used to investigate a continuous solvent extraction process. This is by no means ideal and may result in abandonment of a process that, using another type of contactor, could be found to be entirely satisfactory. 

Experience in solvent extraction processes has shown that such processes can be scaled up from pilot plant—or even bench-scale—data quite reliably. This is particularly evident in processes employing mixer-settlers. However, scale-up will only be as reliable as the data on which it is based, and time spent in obtaining the correct and relevant data will always pay dividends. 

In this process developed by Lurgi [17], the phenolic effluent is contacted with the solvent in a multistage mixer-settler countercurrent extractor (Fig. 10.8). The extract, containing phenol, is separated into phenol and solvent by distillation and solvent is recycled to the extractor. The aqueous raffinate phase is stripped from solvent with gas, and the solvent is recovered from the stripping gas by washing with crude phenol and passed to the extract distillation column. 

Irradiated UO2 is dissolved in nitric acid, resulting in a dissolver solution with the approximate composition listed in Table 12.7. This is treated by the Purex process. The main steps in the conventional Purex process are shown schematically in Fig. 12.5. All existing plants listed in Table 12.8 use some variation of the Purex process. Typically, the extractant composition (percentage TBP, diluent) and the extraction equipment (i.e., pulse columns, mixer-settlers, etc.), vary from plant to plant. However, the upper concentration limit is 30% TBP to prevent a phase reversal due to the increased density of the fully loaded solvent phase. 

---