Sodium hydroxide-water system

Duhring lines, system sodium hydroxide—water. After McCabef)... 

Metal oxide—sodium oxide—water systems at constant temperature exhibit the same general behavior regardless of the particular compounds involved (see Fig. 341). Thus, with increasing alkali hydroxide concentration, the solubility at first increases to a maximum and then decreases sharply. The rising branch of the curve corresponds to solid M(OH)m or MOn while the decreasing branch corresponds to sodium hydroxometalate, whose solubility is sharply reduced as the NaOH concentration increases. 

H. Yokota, The mechanism of cellulose alkalization in the isopropyl alcohol-water sodium hydroxide-cellulose system, J. Appl. Polym. Sci., 30 (1985) 263-277. 

It is quite clear, first of all, that since emulsions present a large interfacial area, any reduction in interfacial tension must reduce the driving force toward coalescence and should promote stability. We have here, then, a simple thermodynamic basis for the role of emulsifying agents. Harkins [17] mentions, as an example, the case of the system paraffin oil-water. With pure liquids, the inter-facial tension was 41 dyn/cm, and this was reduced to 31 dyn/cm on making the aqueous phase 0.00 IM in oleic acid, under which conditions a reasonably stable emulsion could be formed. On neutralization by 0.001 M sodium hydroxide, the interfacial tension fell to 7.2 dyn/cm, and if also made O.OOIM in sodium chloride, it became less than 0.01 dyn/cm. With olive oil in place of the paraffin oil, the final interfacial tension was 0.002 dyn/cm. These last systems emulsified spontaneously—that is, on combining the oil and water phases, no agitation was needed for emulsification to occur. 

Many procedures have been studied for detoxification of aflatoxkis, including heat and treatment with ammonia, methylamine, or sodium hydroxide coupled with extraction from an acetone—hexane—water solvent system. Because ki detoxification it is important to free the toxki from cellular constituents to which it is bound, a stabifi2ation of protekis uskig a tanning compound such as acetaldehyde (qv) or glutaraldehyde may be a solution to the problem (98). 

The reactor effluent, containing 1—2% hydrazine, ammonia, sodium chloride, and water, is preheated and sent to the ammonia recovery system, which consists of two columns. In the first column, ammonia goes overhead under pressure and recycles to the anhydrous ammonia storage tank. In the second column, some water and final traces of ammonia are removed overhead. The bottoms from this column, consisting of water, sodium chloride, and hydrazine, are sent to an evaporating crystallizer where sodium chloride (and the slight excess of sodium hydroxide) is removed from the system as a soHd. Vapors from the crystallizer flow to the hydrate column where water is removed overhead. The bottom stream from this column is close to the hydrazine—water azeotrope composition. Standard materials of constmction may be used for handling chlorine, caustic, and sodium hypochlorite. For all surfaces in contact with hydrazine, however, the preferred material of constmction is 304 L stainless steel. 

The sulfate ester hydrolysate is stripped to give a mixture of isopropyl alcohol, isopropyl ether, and water overhead, and dilute sulfuric acid bottoms. The overhead is neutralized using sodium hydroxide and refined in a two-column distillation system. Diisopropyl ether is taken overhead in the first, ie, ether, column. This stream is generally recycled to the reactors to produce additional isopropyl alcohol by the following equiUbrium reaction ... 

Sodium hypochlorite and calcium hypochlorite are chlorine derivatives formed by the reaction of chlorine with hydroxides. The appHcation of hypochlorite to water systems produces the hypochlorite ion and hypochlorous acid, just as the appHcation of chlorine gas does. 

The sodium salt of CS [9005-22-5] is prepared by reaction of cellulose with sulfuric acid in alcohol followed by sodium hydroxide neutrali2ation (20). This water-soluble product yields relatively stable, clear, and highly viscous solutions. Introduced as a thickener for aqueous systems and an emulsion stabilizer, it is now of no economic significance. 

Caustic Waterflooding. In caustic waterflooding, the interfacial rheologic properties of a model crude oil-water system were studied in the presence of sodium hydroxide. The interfacial viscosity, the non-Newtonian flow behavior, and the activation energy of viscous flow were determined as a function of shear rate, alkali concentration, and aging time. The interfacial viscosity drastically... 

J. Lakatos-Szabd and I. Lakatos. Effect of sodium hydroxide on interfacial rheological properties of oil-water systems. In Colloids Surfaces, Sect A, volume 149, pages 507-513. 9th Surface Colloid Sci Int Conf (Sofia, Bulgaria, 7/6-7/12), 1997. 

High-performance liquid chromatography (HPLC) with a micellar mobile phase or with a selective pre-column or reaction detection system has also been used to determine alkylenebis(dithiocarbamaes). ° Zineb and mancozeb residues in feed were determined by ion-pair HPLC with ultraviolet (UV) detection at 272 nm. These compounds were converted to water-soluble sodium salts with ethylenediaminetetra-acetic acid (EDTA) and sodium hydroxide. The extracts were ion-pair methylated with tetrabuthylammonium hydrogensulfate (ion-pair reagent) in a chloroform-hexane solvent mixture at pH 6.5-8.S. The use of an electrochemical detector has also been reported. ... 

---