Sodium bisulfite sulfate

A.lkyl Sulfosuccinate Half Asters. These detergents are prepared by reaction of maleic anhydride and a primary fatty alcohol, followed by sulfonation with sodium bisulfite. A typical member of this group is disodium lauryl sulfosucciaate [26838-05-1]. Although not known as effective foamers, these surfactants can boost foams and act as stabilizers when used ia combination with other anionic surfactants. In combination with alkyl sulfates, they are said to reduce the irritation effects of the latter (6). 

Sulfation and Sulfonation. a-Olefin reactions involving the introduction of sulfur-containing functional groups have commercial importance. As with many derivatives of olefins, several of these products have appHcations in the area of surfactants (qv) and detergents. Typical sulfur reagents utilized in these processes include sulfuric acid, oleum, chlorosulfonic acid, sulfur trioxide, and sodium bisulfite. 

Physical Properties. Sodium metabisulfite (sodium pyrosulfite, sodium bisulfite (a misnomer)), Na2S20, is a white granular or powdered salt (specific gravity 1.48) and is storable when kept dry and protected from air. In the presence of traces of water it develops an odor of sulfur dioxide and in moist air it decomposes with loss of part of its SO2 content and by oxidation to sodium sulfate. Dry sodium metabisulfite is more stable to oxidation than dry sodium sulfite. At low temperatures, sodium metabisulfite forms hydrates with 6 and 7 moles of water. The solubiHty of sodium metabisulfite in water is 39.5 wt % at 20°C, 41.6 wt % at 40°C, and 44.6 wt % at 60°C (340). Sodium metabisulfite is fairly soluble in glycerol and slightly soluble in alcohol. 

YeUowing of wool can occur during dyeing, depending on pH, temperature and time, and chlorinated wools ate especially sensitive. Bleaching agents that can be added to the dyebath have been developed based on sodium bisulfite and hydroxylamine sulfate (108). Addition of hydrogen peroxide to the dyebath after exhaustion can also be effective. 

After stirring the diazotized solution for 15 minutes, it is slowly poured through a glass-wool filter into a solution of 180 g. (3.4 moles) of potassium iodide in 600 ml. of water. After standing overnight, the heavy dark oil is separated, washed successively with 10% aqueous sodium hydroxide, water, 5% aqueous sodium bisulfite and water, and then dried over magnesium sulfate. 

The enol lactone (12.7 g) is added to 157 ml of 0.5 M perbenzoic acid in benzene and allowed to stand at 25° for 140 hr. The solution is cooled to 15° and 15% sodium bisulfite solution is added to neutralize the excess peracid. The organic layer is separated and washed with saturated sodium bicarbonate solution and water. The benzene solution is dried over anhydrous sodium sulfate, filtered and concentrated to 30 ml. The product is crystallized by adding 80 ml of petroleum ether, filtered and washed with petroleum ether to yield 12.8 g (98%) of 3a,20,23-trihydroxy-16a-methyl-17(20)-oxido-ll-oxo-21-norchol-22-enoic acid-24(20)-lactone 3,23-diacetate mp 225-227°. 

A solution of 100 g of sodium bisulfite in 200 ml of water is added, and the stirring is continued for 10 hours with exclusion of air. A thick precipitate separates after a few minutes. The bisulfite compound is collected by suction filtration, washed with ether until colorless, and then decomposed in a flask with a lukewarm solution of 125 g of sodium carbonate in 150 ml of water. The ketone layer is separated, and the aqueous layer is extracted four times with 30-ml portions of ether. The combined organic layers are dried over anhydrous magnesium sulfate, the ether is removed at atmospheric pressure, and the residual oil is fractionated under reduced pressure through a short column. The cycloheptanone, bp 64-65°/ 2 mm, is obtained in about 40% yield. 

These extracts are then combined with the organic solvent layer and the combined organic phase is extracted four times with 100 ml portions of water. It Is then stirred for an hour with 230 ml of 10% sodium bisulfite solution. The organic solvent phase is then separated, washed seven times with 100 ml portions of water and dried over magnesium sulfate. Evaporation of the solvent gives 1-(4-hydroxy-3-methoxyphenyl)-2-propanone in the form of an oil. 

A mixture of 1.38 grams of the above compound and 15 cc of dioxane was treated with 1.9 cc of a 0.5 N aqueous solution of perchloric acid and 600 mg of N-bromoacetamide, adding the latter in the dark, in three portions, in the course of half an hour and under continuous stirring. It was then stirred for a further 1% hours in the dark, then the excess of reagent was decomposed by the addition of aqueous sodium bisulfite solution and ice water was added the product was extracted with methylene chloride, washed with water, dried over anhydrous sodium sulfate and the solvent was evaporated under reduced pressure, thus giving a yellow oil consisting of the 16,21-diacetate of 6a-fluoro-9a-bromo-16o-hydroxy-hydrocortisone which was used for the next step without further purification. 

To a solution of 6.36 parts of 17(3-hydroxy-17a-methyl-5o -androst-Ten-3-one in 95 parts of acetic acid and 12 parts of water is added 40 parts of lead tetracetate and 0.6 part of osmium tetroxide. This mixture is stored at room temperature for about 24 hours, then is treated with 2 parts of lead tetracetate. Evaporation to dryness at reduced pressure affords a residue, which is extracted with benzene. The benzene extract is washed with water, and extracted with aqueous potassium bicarbonate. The aqueous extract is washed with ether, acidified with dilute sulfuric acid, then extracted with ethyl acetate-benzene. This organic extract is washed with water, dried over anhydrous sodium sulfate, and concentrated to dryness in vacuo. To a solution of the residual crude product in 20 parts of pyridine is added 10 parts of 20% aqueous sodium bisulfite and the mixture is stirred for about 20 minutes at room temperature. 

Strong reducing agents such as sulfur dioxide, sodium bisulfite, sodium metabisulfite, and ferrous sulfate are used in the iron and steel finishing sites to reduce hexavalent chromium to the triva-lent form, which allows the metal to be removed from solution by chemical precipitation.21 23 Metal-containing wastewaters may also be treated by chemical precipitation or ion-exchange. 

As a practical example, following the reduction of hexavalent chromium, sodium hydroxide, lime, or sodium hydroxide can be added to the wastewater to neutralize the pH and precipitate the trivalent chromium, nickel, iron, divalent, and other heavy metals. If lime is used, lime will react with heavy metals and with any residual sodium sulfate, sulfurous acid, or sodium bisulfite. The following reactions apply ... 

A flowsheet for the Wellman-Lord process is shown in Figure 25.26. Again the gas stream with S02 enters a scrubber into which is sprayed a sodium sulfite solution. This then goes to an evaporator/crystallizer to crystallize out the resulting sodium bisulfite, which converts the sodium bisulfite back to sodium sulfate, releasing the S02. The crystals are dissolved in water and recycled to the scrubber. The effect of the Wellman-Lord process is to produce a concentrated S02 stream from a dilute S02 stream. The resulting concentrated S02 still needs to be treated. 

A mixture of 10 g. of D-galactose, 10 ml. of ethyl acetoaeetate, 10 ml. of ethanol, and 5 g. of zinc chloride is heated on a steam bath during 75 minutes. The mixture is cooled, 45 ml. of water is added, and the solution is extracted with two 30-ml. portions of benzene. The aqueous layer is then extracted with nine 15-ml. portions of ethyl acetate. The united extracts are washed successively with an aqueous solution of sodium bisulfite and with an aqueous solution of sodium bicarbonate, dried with anhydrous sodium sulfate, filtered, and the filtrate evaporated to dryness, affording 4.5 g. of a sirup. This is saponified with 12.5 ml. of 10% sodium hydroxide solution, and then acidified (to Congo Red) with phosphoric acid. The aqueous solution is extracted with successive 30-ml. portions of ethyl acetate, and these are dried with anhydrous sodium sulfate, and individually evaporated to dryness. Extracts after the fourth yield a solid product m. p., 130°. Recrystallized from petroleum ether plus acetic acid, the compound has m. p. 132-134° yield, variable, ca. 2%.54... 

A mixture of 2.65 g. of freshly distilled 2,3-O-isopropylidene-D-glycerose, 1.5 ml. of ethyl acetoacetate, 0.7 g. of zinc chloride, 20 ml. of N sulfuric acid, and 20 ml. of 96% ethyl alcohol is kept at room temperature for twenty-four hours. After addition of 3 g. of crystalline sodium acetate and keeping for a further 48 hours at room temperature, the mixture is heated for 15 minutes at 90°. It is then repeatedly extracted with ether, and the united extracts are successively washed with water, an aqueous solution of sodium bisulfite, and a small quantity of aqueous sodium hydroxide solution. The ether layer is dried with anhydrous sodium sulfate and the solvent is evaporated, yielding an oil which is saponified with aqueous sodium hydroxide solution (4 ml. of 10%) by heating on a steam bath for one hour. The aqueous solution is extracted with ether, acidified (to Congo Red) with phosphoric acid, and then repeatedly extracted with ether the united extracts are dried with anhydrous sodium sulfate and the solvent is evaporated, giving a residue which crystallizes from water yield, 0.2 g. of the product (X) m. p., 153-155°. 

The living radical polymerization process is also valid for the polymerization of water-soluble monomers. The polymerization of sodium styrenesulfonate in aqueous ethylene glycol (80%) in the presence of TEMPO using potassium per-sulfate/sodium bisulfite as the initiator at 125 °C gave a water-soluble polymer with well-controlled molecular weight and its distribution [207]. 

Several power plants have been equipped with dual alkali processes. These are throw-away processes with two liquid loops. In one common process, the scrubbing liquid is a clear solution of sodium sulfite. The absorption of sulfur dioxide converts the sodium sulfite to sodium bisulfite. In the regeneration loop, an alkali such as lime slurry is added the sodium sulfite solution is regenerated and a mixture of calcium sulfite and calcium sulfate is precipitated. The slurry is... 

For dual alkali scrubbing, the major dissolved species are sodium chloride, sodium bisulfite, sodium sulfite, and sodium sulfate. If a separate prescrubber is provided for the removal of fly ash and hydrogen chloride before the removal of sulfur dioxide, then sodium chloride will not be present in the sulfur dioxide scrubber. 

A. Preparation of the cuprous chloride solution. A solution of 1250 g. (5 mols.) of crystallized copper sulfate and 325 g. (5.6 mols.) of sodium chloride in 4 1. of hot water is prepared in a x 2-1. flask. The flask is fitted with a mechanical stirrer, and an alkaline solution of sodium sulfite (265 g. of sodium bisulfite and 17 5 g. of sodium hydroxide in 2 1. of water) is added during a period of five to ten minutes. The mixture is allowed to cool to room temperature and washed by decantation. The cuprous chloride is obtained as a white powder, which, however, darkens on exposure to the air. The crude product is dissolved in 2 kg. of commercial 28 per cent hydrochloric acid (sp. gr. 1.14) and the solution is used in the following preparation. 

To a solution of 1200 g. of copper sulfate and 400 g. of sodium chloride in 4 1. of water at 60-70° is added a concentrated solution of 200 g. of (90-95 per cent) sodium bisulfite (prepared if desired by saturating with sulfur dioxide a solution of 100 g. of sodium carbonate). The white precipitate of cuprous chloride is filtered off, sucked dry as rapidly as possible, and suspended in a mixture of 2 1. of water and 1500 cc. of concentrated hydrochloric acid (Note 1). 

It is more convenient to prepare cuprous chloride by reducing copper sulfate with sodium bisulfite than by the action of copper upon cupric chloride (see also p. 33). It is well to test a sample of the filtrate with sodium bisulfite solution no further cuprous chloride should separate. 

Formaldehyde, Methylnitramine, Methylene chloride, Magenesium sulfate. Sulfuric acid. Chloroform, Hexane Nitric acid. Diethanolamine, Ethanol, Ether, Acetone Potassium permanganate, 3-Amino-l,2,4-triazole, Sodium hydroxide. Sodium bisulfite. Hydrochloric acid. Nitric acid, Acetic anhydride. Acetone... 

TNB, Methanol, Potassium iodide, Hydrochloric acid, Sodium bisulfite, Methylene chloride, Magnesium sulfate Hydroxylamine hydrochloride, Glyoxal, Sodium carbonate, Ethanol, Chlorine, Chloroform, Methanol, Ethylenediamine, Ethylene glycol, Sodium hydroxide, Trifluoroacetic anhydride, Nitric acid, Acetone... 

Aluminum foil, Iodine powder. Carbon disulfide, 1,4,6,9-Tetrabromodiamantane, Sodium bisulfite. Hydrochloric acid. Methanol, Acetonitrile, Acetone, Sodium hydroxide. Magnesium sulfate. Potassium permanganate. Toluene Methylene chloride, 2-Bromomethanol, Trioxane, Aluminum chloride. Magnesium sulfate, Nitroform, Acetone, Sodium bicarbonate. Hexane, Silver nitrate. Acetonitrile 1,2-Dichloroethane, HexamethyldisUane, Iodine, Cyclohexane, 1,3-Dioxolane, Nitroform, Methylene chloride, Dimethylformamide, Sodium sulfate. Hydrochloric acid. Magnesium sulfate. Nitric acid. Sulfuric acid Sulfuryl chloride. Acetic anhydride. Nitric acid. Sodium bicarbonate. Sodium sulfate Nitric acid. Sulfuric acid, Malonamide Nitric acid. Sulfuric acid, Cyanoacetic acid Sulfuric acid, Acetasalicyclic acid. Potassium nitrate Nitroform, Diethyl ether, 1-Bromo-l-nitroethane, Sodium sulfuate... 

TNB, Methanol, Potassium iodide, Hydrochloric acid, Sodium bisulfite. Methylene chloride. Magnesium sulfate... 

TNT, Sodium hypochlorite, Tetrahydrofuran, Methanol, Hydrochloric acid Aluminum foil. Iodine powder. Carbon disulfide, 1,4,6,9-Tetrabromodiamantane, Sodium bisulfite. Hydrochloric acid. Methanol, Acetonitrile, Acetone, Sodium hydroxide. Magnesium sulfate. Potassium permanganate. Toluene... 

---